Siloxanes analysis

Solid-phase microextractions also have been developed. In one approach, a fused silica fiber is placed inside a syringe needle. The fiber, which is coated with a thin organic film, such as poly(dimethyl siloxane), is lowered into the sample by depressing a plunger and exposed to the sample for a predetermined time. The fiber is then withdrawn into the needle and transferred to a gas chromatograph for analysis. 

The mechanism of anionic polymerization of cyclosiloxanes has been the subject of several studies (96,97). The first kinetic analysis in this area was carried out in the early 1950s (98). In the general scheme of this process, the propagation/depropagation step involves the nucleophilic attack of the silanolate anion on the sUicon, which results in the cleavage of the siloxane bond and formation of the new silanolate active center (eq. 17). 

FIGURE 9.33 Analysis of cationic poly(amino siloxane). Columns PSS PFG 100 + 1000. Eluent HFIP + O.l A1 KtFat. Temp 25°C. Detection UV 230 nm, Rl. Calibration PSS PDMS siloxane standards. 

GC analysis indicated that the reaction was complete. Gas chromatographic analyses were performed on a Agilent 6890N GC system equipped with a 30-m 5% polyphenyl methyl siloxane capillary column... 

In most of the studies discussed above, except for the meta-linked diamines, when the aromatic content (dianhydride and diamine chain extender), of the copolymers were increased above a certain level, the materials became insoluble and infusible 153, i79, lsi) solution to this problem with minimum sacrifice in the thermal properties of the products has been the synthesis of siloxane-amide-imides183). In this approach pyromellitic acid chloride has been utilized instead of PMDA or BTDA and the copolymers were synthesized in two steps. The first step, which involved the formation of (siloxane-amide-amic acid) intermediate was conducted at low temperatures (0-25 °C) in THF/DMAC solution. After purification of this intermediate thin films were cast on stainless steel or glass plates and imidization was obtained in high temperature ovens between 100 and 300 °C following a similar procedure that was discussed for siloxane-imide copolymers. Copolymers obtained showed good solubility in various polar solvents. DSC studies indicated the formation of two-phase morphologies. Thermogravimetric analysis showed that the thermal stability of these siloxane-amide-imide systems were comparable to those of siloxane-imide copolymers 183>. 

Dynamic mechanical analysis of siloxane-urea copolymers show a sharp loss peak around —110 °C corresponding to the Tg of the siloxane segment. The transition in... 

Product analysis Reaction mixtures were analyzed by GC using a crosslinked 5% phenyl methyl silicone (HP5, 30 m) or a nonbonded, poly(80% biscyanopropyl/20% cyanopropylphenyl siloxane SP2330, 60 m) capillary colunm. Reaction products were identified through their MS (HP 5971 series) and H NMR spectra (Bruker 300... 

The products were identified by comparing the retention times of the reaction products with commercial compounds, and by GC-MS analysis in a Hewlett-Packard 5973/6890 GC equipped with an electron impact ionization at 70 eV detector and a cross-linked 5% PH ME siloxane (0.25 mm coating) capillary column. The reaction products were separated from the catalyst with filter syringes and analyzed in an Agilent 4890D and a Varian 3400 GC equipped with a flame ionization detector, and CP-Sil 8CB (30 m x 0.53 mm x 1.5 pm) and DB-1 (50 m x 0.52 mm x 1.2 pm) columns, respectively. Decane was used as an internal standard. The catalyst was thoroughly washed after reaction with acetonitrile, acetone and water, and dried overnight under vacuum at 40°C. 

Table 7.87 shows the main features of on-line micro LC-GC (see also Table 7.86). The technique allows the high sample capacity and wide flexibility of LC to be coupled with the high separation efficiency and the many selective detection techniques available in GC. Detection by MS somewhat improves the reliability of the analysis, but FID is certainly preferable for routine analysis whenever applicable. Some restrictions concern the type of GC columns and eluent choice, especially using LC columns of conventional dimensions. Most LC-GC methods are normal-phase methods. This is partly because organic solvents used as eluents in NPLC are compatible with GC, making coupling simpler. RPLC-GC coupling is demanding water is not a suitable solvent for GC, because it hydrolyses the siloxane bonds in GC columns. On-line RPLC-GC has not yet become routine. LC-GC technology is only applicable to compounds that can be analysed by GC, i.e. volatile, thermally stable solutes. LC-GC is appropriate for complex samples which are difficult or even impossible to analyse by a single chromatographic technique. Present LC-GC methods almost exclusively apply on-column, loop-type or vaporiser interfaces (PTV).

Table II. NMR Analysis of Poly(Dimethyl Siloxane) Content in Styrenic Graft and Block Copolymers...

Poly(methyl 3-(l-oxypyridinyl)siloxane) was synthesized and shown to have catalytic activity in transacylation reactions of carboxylic and phosphoric acid derivatives. 3-(Methyldichlorosilyl)pyridine (1) was made by metallation of 3-bromopyridine with n-BuLi followed by reaction with excess MeSiCl3. 1 was hydrolyzed in aqueous ammonia to give hydroxyl terminated poly(methyl 3-pyridinylsiloxane) (2) which was end-blocked to polymer 3 with (Me3Si)2NH and Me3SiCl. Polymer 3 was N-oxidized with m-ClC6H4C03H to give 4. Species 1-4 were characterized by IR and H NMR spectra. MS of 1 and thermal analysis (DSC and TGA) of 2-4 are discussed. 3-(Trimethylsilyl)-pyridine 1-oxide (6), l,3-dimethyl-l,3-bis-3-(l-oxypyridinyl) disiloxane (7) and 4 were effective catalysts for conversion of benzoyl chloride to benzoic anhydride in CH2Cl2/aqueous NaHCC>3 suspensions and for hydrolysis of diphenyl phosphorochloridate in aqueous NaHCC>3. The latter had a ti/2 of less than 10 min at 23°C. 

Alkalimetal derivatives of stable functionalized silanols are very important in stepwise formation of siloxane units of almost any size. Thus, a detailed structural analysis is important for assisting understanding of the mechanism of their reactions. The dilithiated derivative of di-ten-butyl si landiol... 

These spacings correspond to cationized fragments with the general composition [SixOyHz]+. The results of the peak analysis prove that the uppermost monolayer of the surface film consists of totally hydrolyzed polymeric siloxanes. There is evidence that these fragments appear as ring- and cage-like silsesquioxane cations (Fig. 2) ... 

---