Silicones phases, properties

Properties of Dense Silicon Carbide. Properties of the SiC stmctural ceramics are shown in Table 1. These properties are for representative materials. Variations can exist within a given form depending on the manufacturer. Figure 2 shows the flexure strength of the SiC as a function of temperature. Sintered or sinter/HIP SiC is the preferred material for appHcations at temperatures over 1400°C and the Hquid-phase densified materials show best performance at low temperatures. The reaction-bonded form is utilized primarily for its ease of manufacture and not for superior mechanical properties. 

The performance of a product where adhesion plays a role is determined both by its adhesive and cohesive properties. In the case of silicones, the promotion of adhesion and cohesion follows different mechanisms [37]. In this context, adhesion promotion deals with the bonding of a silicone phase to the substrate and reinforcement of the interphase region formed at the silicone-substrate interphase. The thickness and clear definition of this interphase is not well known, and in fact depends on many parameters including the surface physico-chemistry of... 

The use of these constants is described in the table in the section entitled Properties of Some Liquid Phases for Packed Columns. The viscosity data, where available, are presented in cSt, which is 10 m2/sec. Cross-linked silicone phases based on the silicones are especially valuable for capillary gas chromatography. They are not specifically treated in this table since the differences in many properties are quite often subtle. The cross-linked phases have much longer lifetimes due to the effective immobilization. 

The preceding section shows how it is possible to deerease the quantity of synthetic polymer while retaining the same fimetional properties. In this way the environmental footprint is diminished, but the produets are still not amenable to recycling processes because of the cross-linking chemistry used in the silicone phase. The feet feat these silicone coatings may be used for their barrier properties should motivate a transition toward this important area of packaging. 

Polytitanosiloxanes were prepared in one stage by simultaneous controlled cocondensation of Si(OEt)4 and Ti(OPr )2(acac)2. A ladder polymer containing Si-0-Si and Si-O-Ti imits is formed. Their ratio depends on the conditions. This ratio determines the time to gel formation and if fiber ceramics can form upon annealing of the material (500-900°C). The structures, growth mechanism and the properties of siloxane composites containing the silicon, titanimn and mixed titanium-silicon phases have been thoroughly reviewed. ... 

Similar in properties to the OV-1 or SE-30 silicone phases (Ref. 1) non-polar fluid suitable for non-polar or slighdy polar analytes thicker coatings extract more analyte, but require longer extraction times thicker coatings may show carryover effects useful for hydrocarbons, 2ildehydes, ketones, and esters. 

Iron—Aluminum and Iron—Aluminum—Silicon Alloys. The influence of aluminum on the physical and magnetic properties of iron is similar to that of silicon, ie, stabilization of the bcc phase, increased resistivity, decreased ductility, and decreased saturation magnetization, magnetocrystalline anisotropy, and magnetostriction. Whereas Si—Ee alloys are well estabHshed for electrical appHcations, the aluminum—iron alloys have not been studied commercially. However, small (up to ca 0.3%) amounts of A1 have been added to the nonoriented grades of siHcon steel, because the decrease in ductiHty is less with A1 than with Si. 

Creep Resistsince. Studies on creep resistance of particulate reinforced composites seem to indicate that such composites are less creep resistant than are monolithic matrices. Silicon nitride reinforced with 40 vol % TiN has been found to have a higher creep rate and a reduced creep strength compared to that of unreinforced silicon nitride. Further reduction in properties have been observed with an increase in the volume fraction of particles and a decrease in the particle size (20). Similar results have been found for SiC particulate reinforced silicon nitride (64). Poor creep behavior has been attributed to the presence of glassy phases in the composite, and removal of these from the microstmcture may improve the high temperature mechanical properties (64). 

This computation is also referred to as calculating the zinc equivalent of the alloy. The increase in strength in this alloy series is caused by increased amounts of beta phase in the stmcture. The silicon brasses show similar hardening effects accompanying a second phase. Typical mechanical properties and electrical conductivity for various cast alloys are shown in Table 2. 

Polymer-Fluid Equilibria and the Glass Transition Most polymer systems fall in the Class HI or Class V phase diagrams, and the same system can often change from one class into the other as the polymer s molecular weight changes. Most polymers are insoluble in CO9 below 100°C, yet CO9 can be quite sohible in the polymer. For example, the sorption of CO9 into silicone rubber is highly dependent upon temperature and pressure, since these properties have a large influence on the density and activity of CO9. 

In the sintering of such materials as silicon nindde, a silica-rich liquid phase is formed which remains in the sintered body as an intra-granular glass, but this phase, while leading to consolidation, can also lead to a deterioration in the high-temperature mechanical properties. 

PDMS based siloxane polymers wet and spread easily on most surfaces as their surface tensions are less than the critical surface tensions of most substrates. This thermodynamically driven property ensures that surface irregularities and pores are filled with adhesive, giving an interfacial phase that is continuous and without voids. The gas permeability of the silicone will allow any gases trapped at the interface to be displaced. Thus, maximum van der Waals and London dispersion intermolecular interactions are obtained at the silicone-substrate interface. It must be noted that suitable liquids reaching the adhesive-substrate interface would immediately interfere with these intermolecular interactions and displace the adhesive from the surface. For example, a study that involved curing a one-part alkoxy terminated silicone adhesive against a wafer of alumina, has shown that water will theoretically displace the cured silicone from the surface of the wafer if physisorption was the sole interaction between the surfaces [38]. Moreover, all these low energy bonds would be thermally sensitive and reversible. 

Nevertheless, silica gel is the material of choice for the production of the vast majority of LC stationary phases. Due to the reactive character of the hydroxyl groups on the surface of silica gel, various organic groups can be bonded to the surface using standard silicon chemistry. Consequently, the silica gel surface can be modified to encompass the complete range of interactive properties necessary for LC ranging from the highly polar to almost completely dispersive. 

A recent competitor to CVD in the planarization of silicon dioxide is the sol-gel process, where tetraethylorthosilicate is used to form spin-on-glass (SOG) films (see Appendix). This technique produces films with good dielectric properties and resistance to cracking. Gas-phase precipitation, which sometimes is a problem with CVD, is eliminated. 

Silicone rubber-hydrogel composite is a two-phase system that is capable of swelling in water. The hydrogels prepared have different chemical compositions, size and shape of particles, and correspondingly different specific surfaces. It was found that the mechanical properties of silicone rubber-hydrogel composites depend mostly on the magnitude of the contact surface of both phases. ... 

---