Rohm and Haas

In the 1980s cost and availabiUty of acetylene have made it an unattractive raw material for acrylate manufacture as compared to propylene, which has been readily available at attractive cost (see Acetylene-DERIVED chemicals). As a consequence, essentially all commercial units based on acetylene, with the exception of BASF s plant at Ludwigshafen, have been shut down. AH new capacity recendy brought on stream or announced for constmction uses the propylene route. Rohm and Haas Co. has developed an alternative method based on aLkoxycarbonylation of ethylene, but has not commercialized it because of the more favorable economics of the propylene route. 

Patents claiming specific catalysts and processes for thek use in each of the two reactions have been assigned to Japan Catalytic (45,47—49), Sohio (50), Toyo Soda (51), Rohm and Haas (52), Sumitomo (53), BASF (54), Mitsubishi Petrochemical (56,57), Celanese (55), and others. The catalysts used for these reactions remain based on bismuth molybdate for the first stage and molybdenum vanadium oxides for the second stage, but improvements in minor component composition and catalyst preparation have resulted in yields that can reach the 85—90% range and lifetimes of several years under optimum conditions. Since plants operate under more productive conditions than those optimum for yield and life, the economically most attractive yields and productive lifetimes maybe somewhat lower. 

Acetylene-Based Routes. Walter Reppe, the father of modem acetylene chemistry, discovered the reaction of nickel carbonyl with acetylene and water or alcohols to give acryUc acid or esters (75,76). This discovery led to several processes which have been in commercial use. The original Reppe reaction requires a stoichiometric ratio of nickel carbonyl to acetylene. The Rohm and Haas modified or semicatalytic process provides 60—80% of the carbon monoxide from a separate carbon monoxide feed and the remainder from nickel carbonyl (77—78). The reactions for the synthesis of ethyl acrylate are... 

The modified Reppe process was installed by Rohm and Haas at thek Houston plant in 1948 and later expanded to a capacity of about 182 X 10 kg/yr. Rohm and Haas started up a propylene oxidation plant at the Houston site in late 1976. The combination of attractive economics and improved product purity from the propylene route led to a shutdown of the acetylene-based route within a year. 

Reppe s work also resulted in the high pressure route which was estabUshed by BASF at Ludwigshafen in 1956. In this process, acetylene, carbon monoxide, water, and a nickel catalyst react at about 200°C and 13.9 MPa (2016 psi) to give acryUc acid. Safety problems caused by handling of acetylene are alleviated by the use of tetrahydrofuran as an inert solvent. In this process, the catalyst is a mixture of nickel bromide with a cupric bromide promotor. The hquid reactor effluent is degassed and extracted. The acryUc acid is obtained by distillation of the extract and subsequendy esterified to the desked acryhc ester. The BASF process gives acryhc acid, whereas the Rohm and Haas process provides the esters dkecdy. 

The process has historic interest. It was replaced at the Rohm and Haas Company by the acetylene-based process in 1954, and in 1970 at Union Carbide by the propylene oxidation process. 

Historically, the development of the acrylates proceeded slowly they first received serious attention from Otto Rohm. AcryUc acid (propenoic acid) was first prepared by the air oxidation of acrolein in 1843 (1,2). Methyl and ethyl acrylate were prepared in 1873, but were not observed to polymerize at that time (3). In 1880 poly(methyl acrylate) was reported by G. W. A. Kahlbaum, who noted that on dry distillation up to 320°C the polymer did not depolymerize (4). Rohm observed the remarkable properties of acryUc polymers while preparing for his doctoral dissertation in 1901 however, a quarter of a century elapsed before he was able to translate his observations into commercial reaUty. He obtained a U.S. patent on the sulfur vulcanization of acrylates in 1912 (5). Based on the continuing work in Rohm s laboratory, the first limited production of acrylates began in 1927 by the Rohm and Haas Company in Darmstadt, Germany (6). Use of this class of compounds has grown from that time to a total U.S. consumption in 1989 of approximately 400,000 metric tons. Total worldwide consumption is probably twice that. 

Synthetic emulsion polymers account for approximately 70% of the U.S. consumption of acrylate monomers. Major end uses for these latex polymers are coatings (32%), textiles (17%), adhesives (7%), paper (5%), and floor poHshes (3%). The U.S. producers of acryflc copolymer emulsions include Rohm and Haas, Reichhold, National Starch, Union Carbide, Air Products, Unocal, B. F. Goodrich, and H. B. Fuller. 

Acryhc Ester Polymers, Survey" in ECT3rd ed., Vol. 1, pp. 386—408, by Benjamin B. Kine and Ronald W. Novak, Rohm and Haas Company. 

Storage and Handling ofAcjlic and Methacj lie Esters and Acids, CM-17, Rohm and Haas Co., Philadelphia, Pa. 

---