Rhodium catalyst acetic anhydride production

This process is one of the three commercially practiced processes for the production of acetic anhydride. The other two are the oxidation of acetaldehyde [75-07-0] and the carbonylation of methyl acetate [79-20-9] in the presence of a rhodium catalyst (coal gasification technology, Halcon process) (77). The latter process was put into operation by Tennessee Eastman in 1983. In the United States the total acetic anhydride production has been reported to be in the order of 1000 metric tons. 

The methyl acetate carbonylation process was successfully started and operated in the early 1980s as part of a coal-to-syngas-to-acetic anhydride complex. This new process introduction resulted in a major improvement in acetic anhydride production economics. In this process, methyl acetate, itself the product of a one-step esterification of acetic acid and methanol, is reacted with carbon monoxide in the presence of a promoted rhodium-iodide catalyst. Figure 22.20 illustrates this process... 

The unit has virtually the same flow sheet (see Fig. 2) as that of methanol carbonylation to acetic acid (qv). Any water present in the methyl acetate feed is destroyed by recycle anhydride. Water impairs the catalyst. Carbonylation occurs in a sparged reactor, fitted with baffles to diminish entrainment of the catalyst-rich Hquid. Carbon monoxide is introduced at about 15—18 MPa from centrifugal, multistage compressors. Gaseous dimethyl ether from the reactor is recycled with the CO and occasional injections of methyl iodide and methyl acetate may be introduced. Near the end of the life of a catalyst charge, additional rhodium chloride, with or without a ligand, can be put into the system to increase anhydride production based on net noble metal introduced. The reaction is exothermic, thus no heat need be added and surplus heat can be recovered as low pressure steam. 

Reppe reaction involves carbonylation of methanol to acetic acid and methyl acetate and subsequent carbonylation of the product methyl acetate to acetic anhydride. The reaction is carried out at 600 atm and 230°C in the presence of iodide-promoted cobalt catalyst to form acetic acid at over 90% yield. In the presence of rhodium catalyst the reaction occurs at milder conditions at 30 to 60 atm and 150-200°C. Carbon monoxide can combine with higher alcohols, however, at a much slower reaction rate. 

An alternative scheme to simultaneous formation of acetaldehyde and acetic anhydride could entail the carbonylation of methyl acetate to acetic anhydride which is subsequently reduced to acetaldehyde and acetic acid. The reaction of acetaldehyde with excess anhydride would form EDA. In fact, Fenton has described production of EDA by the reduction of acetic anhydride using both rhodium and palladium salts as catalysts when modified with triphenylphosphine (26). Two possible mechanisms for the reduction are postulated in equation 16. 

In addition to the successful reductive carbonylation systems utilizing the rhodium or palladium catalysts described above, a nonnoble metal system has been developed (27). When methyl acetate or dimethyl ether was treated with carbon monoxide and hydrogen in the presence of an iodide compound, a trivalent phosphorous or nitrogen promoter, and a nickel-molybdenum or nickel-tungsten catalyst, EDA was formed. The catalytst is generated in the reaction mixture by addition of appropriate metallic complexes, such as 5 1 combination of bis(triphenylphosphine)-nickel dicarbonyl to molybdenum carbonyl. These same catalyst systems have proven effective as a rhodium replacement in methyl acetate carbonylations (28). Though the rates of EDA formation are slower than with the noble metals, the major advantage is the relative inexpense of catalytic materials. Chemistry virtually identical to noble-metal catalysis probably occurs since reaction profiles are very similar by products include acetic anhydride, acetaldehyde, and methane, with ethanol in trace quantities. 

Acetic acid is a key commodity building block [1], Its most important derivative, vinyl acetate monomer, is the largest and fastest growing outlet for acetic acid. It accounts for an estimated 40 % of the total global acetic acid consumption. The majority of the remaining worldwide acetic acid production is used to manufacture other acetate esters (i.e., cellulose acetates from acetic anhydride and ethyl, propyl, and butyl esters) and monoehloroacetic acid. Acetic acid is also used as a solvent in the manufacture of terephthalic acid [2] (cf. Section 2.8.1.2). Since Monsanto commercially introduced the rhodium- catalyzed carbonylation process Monsanto process ) in 1970, over 90 % of all new acetic acid capacity worldwide is produced by this process [2], Currently, more than 50 % of the annual world acetic acid capacity of 7 million metric tons is derived from the methanol carbonylation process [2]. The low-pressure reaction conditions, the high catalyst activity, and exceptional product selectivity are key factors for the success of this process in the acetic acid industry [13]. 

The heavy end products of acetic anhydride processes are separated from catalyst streams and distillation residues. The high affinity of the heavy ends for rhodium components affords specified procedures to separate rhodium and recycle it to the reaction stage of the process. Different methods for rhodium recovery were tested during the process development, including extraction methods [65], precipitation [66], complexing, and electrochemical methods [67]. 

The concept of co-carbonylation of methanol/methyl acetate mixtures was first introduced by BASF in the early 1950s, but the reaction chemistry was not fully developed to commercial realization [75]. Not until the mid-1980s, after the development of carbonylation processes to produce acetic acid and acetic anhydride, were co-carbonylation processes patented using homogeneous rhodium/iodine catalyst systems (Table 2) [2, 56]. The basic process concept is to manufacture acetic acid and acetic anhydride from methanol and carbon monoxide as the only raw materials and to generate methyl acetate within the process. Similiarly, the suitability of dimethyl ether as a raw material for the generation of the anhydride equivalent in addition to or as a substitute for methyl acetate was revealed by Hoechst [76]. To produce a small fraction of acetic acid besides acetic anhydride as the main product, the carbonylation of methyl acetate could be conducted with small amounts of water or methanol. This variant, first demonstrated by Hoechst [56], is practiced by Eastman Kodak [2]. 

It takes place in the liquid phase around 130 to 160 G and between 4 and 7.10 Pa absolute, in the presence of a catalyst complex based onpaHadium or rhodium, methyl iodide, and an amine or phosphine as initiator. Acetic anhydride ts formed as an intermediate. The convefston is directed toward the production of etfaytidene diacetate by increasing the proportionof CO in the synthesis gas. 

---