Resistivity polymers

Heat-resistant fib( Heat-resistant polymers Heat-set inks Heatshield Heat shields Heat stability Heat stabilizers... 

In some instances, the resist polymer can be prepared in a single step by direct polymerization of the protected monomer(s) (37,88), entirely avoiding the intermediate PHOST. HOST-containing resist polymers have also been prepared by free-radical copolymerization of a latent HOST and a stable, acid-labile monomer, eg, the copolymerization of acetoxystyrene with tert-huty acrylate, followed by selective removal of the acetoxy group (89) (Fig. 30). 

Phosphonium Salt—Urea Precondensate. A combination approach for producing flame-retardant cotton-synthetic blends has been developed based on the use of a phosphonium salt—urea precondensate (145). The precondensate is appUed to the blend fabric from aqueous solution. The fabric is dried, cured with ammonia gas, and then oxidized. This forms a flame-resistant polymer on and in the cotton fibers of the component. The synthetic component is then treated with either a cycUc phosphonate ester such as Antiblaze 19/ 19T, or hexabromocyclododecane. The result is a blended textile with good flame resistance. Another patent has appeared in which various modifications of the original process have been claimed (146). Although a few finishers have begun to use this process on blended textiles, it is too early to judge its impact on the industry. 

HEXAFLUOROBENZENE The development of commercial routes to hexafluoroben2ene [392-56-3] included an intensive study of its derivatives. Particularly noteworthy was the development of high temperature lubricants, heat-transfer fluids, and radiation-resistant polymers (248). 

Polyquinoxalines (PQ) have proven to be one of the better heat-resistant polymers with regard to both stabiUty and potential appHcation. The aromatic backbones are derived from the condensation of a tetramine with a bis-glyoxal, reactions first done in 1964 (61,62). In 1967, a soluble, phenylated version of this polymer was produced (63). The chemistry and technology of polyquinoxalines has been reviewed (64). 

New heat-resistant polymers containing -iiitrophenyl-substituted quinoxaline units and imide rings as well as flexible amide groups have been synthesi2ed by polycondensation reaction of a dianainoquinoxaline derivative with diacid dichlorides (80). These polymers are easily soluble in polar aprotic solvents with inherent viscosities in the range of 0.3—0.9 dL/g in NMP at 20°C. AH polymers begin to decompose above 370°C. 

Heat-Resistant Polymers" in ECT 3rd ed., Vol. 12, pp. 203—225, byj. Preston, Monsanto Triangle Park Development Center, Inc. 

Copolymers. The copolymer of tetrabromoBPA and BPA was one of the first commercially successhil copolymers. Low levels of the brominated comonomer lead to increased flame resistance (V-0 rating by UL 94) while having htde effect on other properties. The polycarbonate of bis(4-hydtoxyphenyl)-l,l-dichlotoethylene, prepared from chloral and phenol, followed by dehydrohalogenation, was investigated as another flame-resistant polymer which retained good impact properties. 

DADC HomopolymeriZation. Bulk polymerization of CR-39 monomer gives clear, colorless, abrasion-resistant polymer castings that offer advantages over glass and acryHc plastics in optical appHcations. Free-radical initiators are required for thermal or photochemical polymerization. 

Polymers from the meta isomer are useful for their heat and flame resistance polymers from the para isomer are noted for high tensile strength and high modulus. 

Fig. 8. Electron micrograph of Merino wool fibers in a fabric that have been treated with a typical shrink-resistance polymer, showing fiber—fiber bond...

Acrylic Resins. The first synthetic polymer denture material, used throughout much of the 20th century, was based on the discovery of vulcanised mbber in 1839. Other polymers explored for denture and other dental uses have included ceUuloid, phenolformaldehyde resins, and vinyl chloride copolymers. Polystyrene, polycarbonates, polyurethanes, and acryHc resins have also been used for dental polymers. Because of the unique combination of properties, eg, aesthetics and ease of fabrication, acryHc resins based on methyl methacrylate and its polymer and/or copolymers have received the most attention since their introduction in 1937. However, deficiencies include excessive polymerization shrinkage and poor abrasion resistance. Polymers used in dental appHcation should have minimal dimensional changes during and subsequent to polymerization exceUent chemical, physical, and color stabiHty processabiHty and biocompatibiHty and the abiHty to blend with contiguous tissues. 

Low Temperature Properties. Medium hardness compounds of average methyl acrylate, ie, VAMAC G, without a plasticizer typically survive 180° flex tests at —40° C. Such performance is good for a heat-resistant polymer. Low temperature properties can be greatly enhanced by the use of ester plasticizers (10). Careful selection of the plasticizer is necessary to preserve the heat resistance performance of the polymer. Plasticized high methyl acrylate grades lose only a few °C in flexibiUty, compared to grades with average methyl acrylate levels. 

Freeze-Resistant Polymers. Chloroprene homopolymers made at conventional polymerization temperatures of 40—50°C are not sufftcientiy freeze resistant for some appHcations. In particular, automotive parts such as belts, boots, and air springs are used in dynamic appHcations and need... 

In the 1960s, CIBA Products Co. marketed and manufactured glycidylated o-cresol novolak resins, which had been developed by Koppers Co. as high temperature-resistant polymers. Dow offered glycidylated phenol novolak resins, SheU introduced polyglycidyl ethers of tetrafunctional phenols, and Union Carbide developed a triglycidyl p- am in oph en o1 resin. 

The thermoset polyimides are a family of heat-resistant polymers with acceptable properties up to 260°C (500°F). They are unaffected by dilute acids, aromatic and ahphatic hydrocarbons, esters, ethers, and alcohols but are attacked by dilute alkahes and concentrated inorganic acids. 

In some countries the extensive use of asbestos as a filler is somewhat discouraged because of the hazards associated with its use. In other parts of the world moulding compositions of enhanced heat resistance have been developed by the use of especially heat-resisting polymers used in conjunction with asbestos and other mineral fillers. 

---