Resistance, lithium polymer batterie

Electrodes and cell components must be thin to minimise the internal resistance of the batteries the total cell can be less than 0.2 mm thick. Figure 12.11 shows the construction of a multi-layer film, rechargeable lithium polymer battery, using a solid polymer electrolyte. A thin lithium metal foil acts as an anode. The electrolyte is polyethylene oxide containing a lithium salt, and the cathode is a composite of the electrolyte and a... 

Lithium polymer electrolytes formed by dissolving a lithium salt LiX (where X is preferably a large soft anion) in poly(ethylene oxide) PEO can find useful application as separators in lithium rechargeable polymer batteries.Thin films must be used due to the relatively high ionic resistivity of these polymers. For example, the lithium-ion conductivity of PEO—Li salt complexes at 100 °C is still only about Viooth the conductivity of a typical aqueous solution. 

The strategy of hybrid and gel electrolytes is very promising for lithium-ion batteries, but it seems less viable for lithium-metal batteries due to the reactivity of lithium metal with the encapsulated solvent. In fact, high conductivity is not the only parameter in selecting a successful polymer electrolyte for the development of lithium batteries a low interface resistance and a high interface stability over time are also required to assure good cyclability and long life. 

There is as yet no consolidated opinion as to the optimum electrolyte for lithium-sulfiir batteries. Experiments with solid polymer electrolyte are described, but aprotic electrolyte in a Celgard-type separator commonly used in lithium ion batteries is applied more frequently. A large number of electrolytes has been studied that differ both in solvents and the lithium salt. The greatest acceptance was gained by lithium imide solutions in dioxolane (or in a mixture of dioxolane and dimethoxyethane) and also lithium perchlorate solutions in sulfone. Dissolution of polysulfides in electrolyfe is accompanied by a noticeable increase in viscosity and specific resistance of electrolyte. It is the great complexity of the composition of the electrochemical system and that of the processes occurring therein that prevent as yet commercialization of lithium-sulfiir electrolytes. 

Alternatively, a roll can be wound to fit a prismatic case as commonly found in lithium ion batteries. The roll is placed in a fitted conductive metal casing that has a Teflon or rubber gasket seal separating the outer can and top button contact. The cylindrical metal rod around which the film is wound becomes the internal contact. Contacts are ensured by soldering and then electrolyte is injected into the cell followed by a curable polymer sealant. The top of the casing is fitted with a vent, gasket layer, and top contact plate. To seal the device, the top of the can is mechanically crimped and the outer metal casing acts as the other contact and provides mechanical stability and rupture resistance. 

A matrix of gel polymer electrolyte is coated on the surface of a polyolefin microporous membrane. The polyolefin microporous membrane provides mechanical support and chemical stability, while the coated polymer absorbs organic liquid electrolyte and provides high ionic conductivity. The coating of the gelling polymer is also beneficial for close contact between the polyolefin microporous membrane and the electrodes, decreasing the internal resistance. This method was first applied successfully by Sony Corporation to manufacture polymer lithium-ion batteries. 

In relation to the safety problems of lithium-ion batteries, shutdown behavior has been a well-discussed topic. At elevated temperature, one polymer in a separator will melt down, and the porous structure is closed. As a result, ions cannot be transported, leading to a sharp increase in resistance. This temperature is known as the shutdown temperature. If this temperature is too low, the lithium-ion battery can simply stop working. If it is too high, there is the danger of sharp thermal production. It is important to select polymer materials to tailor the shutdown temperature for the separator. Optimizing the polymer components and porous structure can realize a separator that will shut down at a targeted temperature. 

It is claimed that the cured materials may be used continuously in air up to 300°C and in oxygen-free environments to 400°C. The materials are of interest as heat- and corrosion-resistant coatings, for example in geothermal wells, high-temperature sodium and lithium batteries and high-temperature polymer- and metal-processing equipment. 

Ionically conducting polymers and their relevance to lithium batteries were mentioned in a previous section. However, there are several developments which contain both ionically conducting materials and other supporting agents which improve both the bulk conductivity of these materials and the properties of the anode (Li)/electrolyte interface in terms of resistivity, passivity, reversibility, and corrosion protection. A typical example is a composite electrolyte system comprised of polyethylene oxide, lithium salt, and A1203 particles dispersed in the polymeric matrices, as demonstrated by Peled et al. [182], By adding alumina particles, a new conduction mechanism is available, which involved surface conductivity of ions on and among the particles. This enhances considerably the overall conductivity of the composite electrolyte system. There are also a number of other reports that demonstrate the potential of these solid electrolyte systems [183],... 

Kureha KF polymer is a PVdF product developed by Kureha Corporation, Tokyo Japan. KF polymer has a high chemical resistance and desirable mechanical properties. One of its most remarkable characteristics is that the irregular bonding of its molecular chain is lower than that of any of the other PVdFs, an attribute that leads to a perfectly crystallized polymer. These valuable properties allow lithium-ion secondary batteries to combine long-term, stable performance with a minimum amount of swelling by the organic electrolyte. 

---