Resin activation methods

In a more recent study using dedicated multimode microwave reactors for chemical synthesis, which enable temperature and power control, it was demonstrated that microwave irradiation could be effectively employed to couple aromatic carboxylic acids to polystyrene Wang resin [25], if the symmetrical anhydride procedure was used, and not the three-component O-acylisourea activation method [19]. Almost quantitative loading was achieved in l-methyl-2-pyrrolidone (NMP) at 200 °C within 10 min under... 

The acid chloride method has been successfully used for the synthesis of depsipeptides by O-acylation of hydroxy acids. Although Fmoc amino acid chlorides were recommended for such reactions, and can be used for the introduction of the first amino acid onto hydroxy resins for SPPS, oxazol-5(4//)-one formation promoted by the presence of the required tertiary amine leads to relatively low yields compared to other activation methods such as those involving UNCA groups. ... 

The standard activation method on the Pioneer is with AI-[(dimethylannino)(3-oxido-l//-l,2,3-triazolo[4,5-b]pyridin-l-yl)methylene]-A-methylmethananunium hexafluorophosphate (HATU). The concentration of activated amino add depends on the scale of synthesis, ranging from 0.06 M (0.02-mmol scale) to 0.13 M (0.1-mmol scale) to 0.25 M (>0.2-mmol scale). The recommended resin for the Pioneer is PEG-PS. The volume of the column depends on the void volume of the solid support (the void volume for PEG-PS is ca.4.4mL-g" ). 

A number of methods are being tested for enzyme immobilization. The method selected depends on the operating details of the enzyme system employed and the nature of the solvent to be used, which is usually water. Enzyme, or inactivated cells, may be encapsulated in a film, or encased in a gel, which is permeable to both the substrate and product, but not to enzyme [77]. Porous glasses or insoluble polymers such as a derivatized cellulose may be used as a support onto which enzyme is adsorbed. Pendant functional groups of a polymer, such as those of the ion-exchange resins, can be used either to ionically bind the enzyme to the resin active sites or to covalently bond the enzyme to the resin [79]. The enzyme may be bonded to a polymer backbone chain using a bifunctional monomer such as glutaraldehyde to react with enzyme sites that do not affect its catalytic activity [80]. 

The adsorption of biomolecules onto carriers that are insoluble in water is the simplest method of immobilization. An aqueous solution of the biomolecules is contacted with the active carrier material for a defined period of time. Thereafter the molecules that are not adsorbed are removed by washing. Anionic and cationic ion exchange resins, active charcoal, silica gel, clay, aluminum oxide, porous glass, and ceramics are being currently used as active material. The carrier should exhibit high affinity and capacity for the biomolecule and the latter must remain active in the adsorbed state. The carrier should adsorb neither reaction products nor inhibitors of the biocatalyst. 

Adsorption. Some organics are not removed in biological systems operating under normal conditions. Removal of residual organics can be achieved by adsorption. Both activated carbon and synthetic resins are used. As described earlier under pretreatment methods, regeneration of the activated carbon in a furnace can cause carbon losses of perhaps 5 to 10 percent. 

The major disadvantage of solid-phase peptide synthesis is the fact that ail the by-products attached to the resin can only be removed at the final stages of synthesis. Another problem is the relatively low local concentration of peptide which can be obtained on the polymer, and this limits the turnover of all other educts. Preparation of large quantities (> 1 g) is therefore difficult. Thirdly, the racemization-safe methods for acid activation, e.g. with azides, are too mild (= slow) for solid-phase synthesis. For these reasons the convenient Menifield procedures are quite generally used for syntheses of small peptides, whereas for larger polypeptides many research groups adhere to classic solution methods and purification after each condensation step (F.M. Finn, 1976). 

Softening and cure is examined with the help of a torsional pendulum modified with a braid (65), which supports thermosets such as phenoHcs and epoxies that change from a Hquid to a soHd on curing. Another method uses vibrating arms coupled to a scrim-supported sample to measure storage and loss moduH as a function of time and temperature. An isothermal analytical method for phenoHc resins provides data regarding rate constants and activation energies and allows prediction of cure characteristics under conditions of commercial use (47). 

Distillation trays constiircted of porous catalyticaUy active material and reinforcing resins Method described for removing or replacing catalyst on trays as a hquid slurry Catalyst bed placed in downcomer, designed to prevent vapor None specified Wang et al., Chinese Patent 1,060,228 (1992) Jones, U.S. Patent, 5,1.3.3,942 (1992)... 

---