Regularization correction

Monitor serum electrolytes and arterial blood gases regularly. Correct metabolic acidosis slowly to prevent the development of metabolic alkalosis or other electrolyte abnormalities. 

I. Goidenko, G. Plunien, A. Nefiodov, S. Zschocke, L. Labzowsky, and G. Soff No regularization corrections to the partial-wave renormalization procedure, hep-ph/0006220... 

Regularization Corrections to the Partial-Wave Renormalization Procedure ... 

This hst of basic items covered ia a mock OSHA iaspection appear to be obvious items that any faciUty should observe. However, nearly every safety or fire iaspection uncovers these items duriag iaspections, causiag the faciUty to receive fines or warnings because maintenance people do not perform their own regular and thorough iaspections of their faciUties to avoid corrective actions by code enforcing agencies. 

Issuance of a United States patent transforms a patent appHcant into a patentee, and new concerns may arise relevant to management. For example, the patent should be reviewed to determine formal and substantive correctness. An audit should be taken regularly to determine whether there is a continuing justification to pay the maintenance fees required to keep the patent in force during its effective period. The patentee or patent assignee may have to address concerns of patent infringement or patent vaHdity. 

Aromatic ethers 11.5-N -140.04-1- 13.869N The AN value is not a correction to regular ether value, but the AB value is a correction to regular etheF... 

Primary amines with NH2 group on aromatic nucleus 15.04-N 0 The AN value is not a correction to regular amine value to find AB, use primary amine valiie" ... 

The polarization cell must be inspected at regular intervals (e.g., twice a year) to check water loss caused by electrolysis. If necessary, the correct level must be restored with deionized water. In addition, the electrolyte should be renewed every 4 years. It is recommended that the dc decoupling device be designed so that the maximum expected failure current flows through the smallest possible polarization cell in order to load the cathodic protection as little as possible. 

In all these applications it should be realized that the safety provided by corrosion protection depends on its efficacy. The system must not only be correctly installed at the commissioning stage but must also be monitored continually, or at regular intervals during operation [1]. In this respect the methods of measurement used in monitoring cannot be too highly emphasized. 

Control fluid quality during use, involving checks on correct dilution and make-up, concentration and freedom from contamination in service, regular cleaning and fluid changing Provide and use appropriate personal protective equipment A high standard of personal hygiene... 

Eire equipment Fire alarm and fire-fighting equipment must be regularly inspected, maintained and tested Portable extinguishers to have designated locations/be of correct type. Instructions must be provided as to where and how to use them. Practice is necessary... 

Chlorine monitors should be strategically located within the plant to detect chlorine releases or leaks on a continuous basis. Monitoring data should be analyzed and reviewed at regular intervals and compared with the operating standards so that any necessary corrective actions can be taken. 

In the case of a closed water system, once the correct water treatment is provided, the incidence of microbiological fouling or corrosion is virtually eliminated, provided that the addition of fresh water is not a frequent occurrence. It is, however, essential to have water tests carried out at regular intervals by a water laboratory. 

Linnecessary noise, these should be cleaned regularly. Imbalance, whether due to dirt or to other causes, should be corrected by adjustment. Detective bearings should be adjusted or replaced. Struts and sharp edges in front of an impeller should be avoided. Impact noise insulation should be introduced between fan room and floor structure and between fan room and connecting ducts. The fan unit should be enclosed, with satisfactory airborne sound insulation as the objective. 

Check valves have a bad name among many plant operators. However, this is because many of these valves are never inspected or tested. No equipment, especially that containing moving parts, can be expected to work correctly forever without inspection and repair. When check valves are relied on for emergency isolation, they should be scheduled for regular inspection. 

Once deficiencies have been identified, tlie plan should be revised to correct tlicni. Such testing and revision should be done regularly tlie interval between tests and revisions should not exceed one year. 

---