Recycling advantages

Ube developed the PA nanocomposite named Ecobesta to replace PVDF or other traditional barrier materials. The all-polyamide structure offers recycling advantages compared to traditional multi-materi designs. It incorporates ... 

Bench-scale kinetic experiments can be conducted in batch, continuous stirred-tank (CSTR), tubular plug-flow, or differential reactors. The last of these can be operated with once-through flow or recycle. Advantages and disadvantages of the various types are discussed. In particular Batch reactors are inexpensive, but require attention to rapid attainment of reaction conditions at start CSTRs are excellent for gas-liquid, but less so for gas-phase reactions tubular reactors are especially suited for reactions of heterogeneous catalysis and differential reactors operated "once through" are best for measurement of initial rates. 

Air knife coater works in a way similar to a normal knife coater except that the excess of coating is blown off by air under pressure (Fig. 42). This technique works only with very fluid adhesives (less than 500 mPas) with low solids. Also the solvents should dry slowly or else blowing air could cause a skinning over the adhesive surface. When working with a water-based adhesive, the blown air should be saturated with water vapour so that the excess of adhesive could be recycled. Advantages ... 

In addition to the advantage of high heat transfer rates, fluidized beds are also useful in situations where catalyst particles need frequent regeneration. Under these circumstances, particles can be removed continuously from the bed, regenerated, and recycled back to the bed. In exothermic reactions, the recycling of catalyst can be... 

In 1994 in the U.S., recycled PET, HDPE, LDPE, and PS had a 16—46% cost advantage (4). This cost advantage largely disappeared by 1996. Bureau of Labor Statistics data indicate U.S. plastics prices in mid-1997 are seven percent below those of mid-1995 after being more than ten percent less in 1996... 

The protonated form of poly(vinyl amine) (PVAm—HCl) has two advantages over many cationic polymers high cationic charge densities are possible and the pendent primary amines have high reactivity. It has been appHed in water treatment, paper making, and textiles (qv). The protonated forms modified with low molecular weight aldehydes are usehil as fines and filler retention agents and are in use with recycled fibers. As with all new products, unexpected appHcations, such as in clear antiperspirants, have been found. It is usehil in many metal complexation appHcations (49). 

When the gas available for regeneration is in short supply, the regeneration steps ate often carried out in a closed loop. This recycle of the bed effluent back to the inlet has the advantage of concentrating the impurity and making it easier to separate by condensation or other recovery means. 

The majority of thermal polymerizations are carried out as a batch process, which requires a heat-up and a cool down stage. Typical conditions are 250—300°C for 0.5—4 h in an oxygen-free atmosphere (typically nitrogen) at approximately 1.4 MPa (200 psi). A continuous thermal polymerization has been reported which utilizes a tubular flow reactor having three temperature zones and recycle capabiHty (62). The advantages of this process are reduced residence time, increased production, and improved molecular weight control. Molecular weight may be controlled with temperature, residence time, feed composition, and polymerizate recycle. 

Tube-Cooled Converter. The tube-cooled converter functions as an interchanger, consisting of a tube-filled vessel with catalyst on the shell side (Fig. 7c). The combined synthesis and recycle gas enters the bottom of the reactor tubes, where it is heated by the reaction taking place in the surrounding catalyst bed. The gas turns at the top of the tubes and passes down through the catalyst bed. The principal advantage of this converter is in... 

Oxygen, often the VSA-produced 90—93% purity, is beginning to be used for the recycling of aluminum because of advantages 1—4). 

Lewis acids, such as the haUde salts of the alkaline-earth metals, Cu(I), Cu(II), 2inc, Fe(III), aluminum, etc, are effective catalysts for this reaction (63). The ammonolysis of polyamides obtained from post-consumer waste has been used to cleave the polymer chain as the first step in a recycle process in which mixtures of nylon-6,6 and nylon-6 can be reconverted to diamine (64). The advantage of this approach Hes in the fact that both the adipamide [628-94-4] and 6-aminohexanoamide can be converted to hexarnethylenediarnine via their respective nitriles in a conventional two-step process in the presence of the diamine formed in the original ammonolysis reaction, thus avoiding a difficult and cosdy separation process. In addition, the mixture of nylon-6,6 and nylon-6 appears to react faster than does either polyamide alone. 

---