Real quality

Commodities had found their perfect finish. Aniline paints and dyes had first been marketed as more valuable because they were more real . This real quality was based on the fact that they did not fade. Plastic likewise was marketed as a substance that was not tarnished by history or nature. Both Roland Barthes and Tupperware would make a virtue of plastic s mutability and flexibility. Plastic s essential oneness could be seen as transcendental. Barthes, in 1957, called it the very stuff of alchemy , for, as raw, telluric matter , it is shaped automatically and miraculously, into buckets or jewels or anything. Nature is outbid. Euphorically, humans freewheel through it. Barthes also noted plastic s undoing its lack of substance, its flatness, its chemical colouration, its prosaicness, its lack of pretension. 

This strength only becomes manifest in the presence of a suitable base or proton acceptor, in which case appropriate values of such acidity parameters as Hammett s Ho can be measured. In rather simplistic terms one could draw a parallel between the Ho values and the relative ease with which a given monomer would be protonated if dissolved in the pure acids. Unfortunately, this protonation capacity is not a sufficient criterion to establish the potential usefulness of a Br nsted acid as initiator in cationic polymerisation, although it does represent an important parameter. Other factors, such as the solubility of the acid in the common solvents used, its inertness towards them, the relative stability of the ions formed in the protonation reaction against their collapse to the corresponding ester, etc., can play a major role in determining the real qualities of these possible initiators. 

Fig. 4.49 Qualitative plot of the real quality x eal against the thermodynamic quality...

However, in regions of intermediate quality, where neither subcooled boiling or spray flow occur, (4.116) delivers exact values. Fig. 4.49 shows a qualitative plot of the real quality x eal against the thermodynamic quality x h based on (4.116). 

Appreciation of the need for real quality standards must therefore be one of the con siderations during the conceptual studies by the product research department of the large multinational companies and by a market research assessment of the potential market slot. It requires an assessment of the market the product is intended to satisfy, followed by the incorporation of these market requirements into the first paper designs. 

The real quality is the fraction of gas flow relative to the total flow and is given as... 

In Quality Is Free [1], Crosby outlines five points of what the term real quality means, emphasizing the absolutes of quality management. Table 0-1, Comparing Quality to Safety, lists these points. In addition, the authors have related these elements as they would fit into a safety management system. 

Fig. 1 shows the two-layered profile on a substrate. The quality of reconstruction of this highly contrasted profile is good. The reconstruction of a more complicated three-layered profile on a substrate is shown in Fig. 2. To estimate the robusmess of the approach, a random signal uniformly distributed over the interval [-0.02 +0.02] was added to the real and...

Of all NTD methods for quality control of materials, products, welded and soldered joints the most informative and perspective are radioscopic ones that enable to obtain a visual image of an inner structure of a tested objects in real time under any projection. 

The lead time for making a image by film X-Ray is 10 to 15 minutes. Where about 2 minute are needed in inspection by Real-Time X-Ray. Another advantage of Real-Time X-Ray is the feature that the effect of manipulating the part or changing the setting of the X-Ray tube can be observed directly. This is often used in investigating quality problems. 

The tests concluded that it was possible to use real time X-ray to inspect incoming frozen fish blocks 100% and giving a completely accurate assessment of the quality of the blocks to enable the factory to calculate the correct purchase price as a function of the bone content. 

CR-1629 Non destructive real-time control of the quality of electrical spot welding Dr. M. Cherfaoui CETIM... 

Undeniably, one of the most important teclmological achievements in the last half of this century is the microelectronics industry, the computer being one of its outstanding products. Essential to current and fiiture advances is the quality of the semiconductor materials used to construct vital electronic components. For example, ultra-clean silicon wafers are needed. Raman spectroscopy contributes to this task as a monitor, in real time, of the composition of the standard SC-1 cleaning solution (a mixture of water, H2O2 and NH OH) [175] that is essential to preparing the ultra-clean wafers. 

The LMTO method [58, 79] can be considered to be the linear version of the KKR teclmique. According to official LMTO historians, the method has now reached its third generation [79] the first starting with Andersen in 1975 [58], the second connnonly known as TB-LMTO. In the LMTO approach, the wavefimction is expanded in a basis of so-called muffin-tin orbitals. These orbitals are adapted to the potential by constmcting them from solutions of the radial Scln-ddinger equation so as to fomi a minimal basis set. Interstitial properties are represented by Hankel fiinctions, which means that, in contrast to the LAPW teclmique, the orbitals are localized in real space. The small basis set makes the method fast computationally, yet at the same time it restricts the accuracy. The localization of the basis fiinctions diminishes the quality of the description of the wavefimction in die interstitial region. 

Quality in Japan. Japanese economic prowess has been attributed variously to such quahty improvement activities as quahty circles, statistical process control (SPG), just-in-time dehvery (JIT), and zero defects (ZD). However, the real key to success hes in the apphcation of numerous quahty improvement tools as part of a management philosophy called Kaizen, which means continuous improvement (10). 

Fortunately, it was found that in polypeptide systems the effective dimensionality of conformational spaces is significantly smaller than the dimensionality of the full space, with only a few principal axes contributing to the projection [38-41]. In fact, in many cases a projection quality of 70-90% can be achieved in as few as tliree dimensions [42], opening the way for real 3D visualization of molecular conformational space. Figure 8... 

The present author was worried about the lack of knowledge concerning the quality of the kinetic models used in the industry. A model is by definition a small, scaled-down imitation of the real thing. (Men should remember tliis when their mothers-in-law call them model husbands.) In the industry all we require from a kinetic model is that it describe the chemical rate adequately by using traditional mathematical forms (Airhenius law, power law expressions and combinations of these) within the limits of its applications. Neither should it rudely violate the known laws of science. 

---