Reaction system catalytic reactor

Heavy water [11105-15-0] 1 2 produced by a combination of electrolysis and catalytic exchange reactions. Some nuclear reactors (qv) require heavy water as a moderator of neutrons. Plants for the production of heavy water were built by the U.S. government during World War II. These plants, located at Trad, British Columbia, Morgantown, West Virginia, and Savaimah River, South Carolina, have been shut down except for a portion of the Savaimah River plant, which produces heavy water by a three-stage process (see Deuterium and tritium) an H2S/H2O exchange process produces 15% D2O a vacuum distillation increases the concentration to 90% D2O an electrolysis system produces 99.75% D2O (58). 

For catalytic reactions in an open system, V reactor volume contains the catalyst and concentrations arc referred per unit of flowing volume, m /s. 

The scheme of commercial methane synthesis includes a multistage reaction system and recycle of product gas. Adiabatic reactors connected with waste heat boilers are used to remove the heat in the form of high pressure steam. In designing the pilot plants, major emphasis was placed on the design of the catalytic reactor system. Thermodynamic parameters (composition of feed gas, temperature, temperature rise, pressure, etc.) as well as hydrodynamic parameters (bed depth, linear velocity, catalyst pellet size, etc.) are identical to those in a commercial methana-tion plant. This permits direct upscaling of test results to commercial size reactors because radial gradients are not present in an adiabatic shift reactor. 

The ratio of the observed reaction rate to the rate in the absence of intraparticle mass and heat transfer resistance is defined as the elFectiveness factor. When the effectiveness factor is ignored, simulation results for catalytic reactors can be inaccurate. Since it is used extensively for simulation of large reaction systems, its fast computation is required to accelerate the simulation time and enhance the simulation accuracy. This problem is to solve the dimensionless equation describing the mass transport of the key component in a porous catalyst[l,2]... 

For the non-oxidative activation of light alkanes, the direct alkylation of toluene with ethane was chosen as an industrially relevant model reaction. The catalytic performance of ZSM-5 zeolites, which are good catalysts for this model reaction, was compared to the one of zeolite MCM-22, which is used in industry for the alkylation of aromatics with alkenes in the liquid phase. The catalytic experiments were carried out in a fixed-bed reactor and in a batch reactor. The results show that the shape-selective properties of zeolite ZSM-5 are more appropriate to favor the dehydroalkylation reaction, whereas on zeolite MCM-22 with its large cavities in the pore system and half-cavities on the external surface the thermodynamically favored side reaction with its large transition state, the disproportionation of toluene, prevails. 

For gas phase heterogeneous catalytic reactions, the continuous-flow integral catalytic reactors with packed catalyst bed have been exclusively used [61-91]. Continuous or short pulsed-radiation (milliseconds) was applied in catalytic studies (see Sect. 10.3.2). To avoid the creation of temperature gradients in the catalyst bed, a single-mode radiation system can be recommended. A typical example of the most advanced laboratory-scale microwave, continuous single-mode catalytic reactor has been described by Roussy et al. [79] and is shown in Figs. 10.4 and... 

NASA conducted studies on the development of the catalysts for methane decomposition process for space life-support systems [94], A special catalytic reactor with a rotating magnetic field to support Co catalyst at 850°C was designed. In the 1970s, a U.S. Army researcher M. Callahan [95] developed a fuel processor to catalytically convert different hydrocarbon fuels to hydrogen, which was used to feed a 1.5 kW FC. He screened a number of metals for the catalytic activity in the methane decomposition reaction including Ni, Co, Fe, Pt, and Cr. Alumina-supported Ni catalyst was selected as the most suitable for the process. The following rate equation for methane decomposition was reported ... 

The interest in the dynamic operation of heterogeneous catalytic systems is experiencing a renaissance. Attention to this area has been motivated by several factors the availability of experimental techniques for monitoring species concentrations both in the gas phase and at the catalyst surface with a temporal resolution and sensitivity not previously possible, the development of efficient numerical methods for predicting the dynamics of complex reaction systems, and the recognition that in selected instances operation of a catalytic reactor under dynamic conditions can yield a better performance than operation under steady-state conditions. 

Our treatment of Chemical Reaction Engineering begins in Chapters 1 and 2 and continues in Chapters 11-24. After an introduction (Chapter 11) surveying the field, the next five Chapters (12-16) are devoted to performance and design characteristics of four ideal reactor models (batch, CSTR, plug-flow, and laminar-flow), and to the characteristics of various types of ideal flow involved in continuous-flow reactors. Chapter 17 deals with comparisons and combinations of ideal reactors. Chapter 18 deals with ideal reactors for complex (multireaction) systems. Chapters 19 and 20 treat nonideal flow and reactor considerations taking this into account. Chapters 21-24 provide an introduction to reactors for multiphase systems, including fixed-bed catalytic reactors, fluidized-bed reactors, and reactors for gas-solid and gas-liquid reactions. 

It is not practical to stir all reaction systems, for example, bulk polymerizations, postpolymerization reactions, fixed-bed catalytic reactors, and plug-flow reactors. Although multipoint temperature sensing is often used as a key solution to determine a runaway in nonagitated vessels, the occurrence of hot spots may not always be detected. 

---