Reaction plug-flow

Table 8.1 presents the results of the ICR retention time studies, sugar concentration (dual substrate) studies and cell density. The kinetic model for ICR was derived on the basis of a first order reaction, plug flow and steady-state behaviour. 

Figure 11.5 Effective yield of the intermediate product as a function of conversion for first-order consecutive reactions (plug flow reactor), (a) Influence of internal mass transfer resistance and (b) influence of external mass transfer resistance.

Continuous plug flow reactors are also unsuitable for these purposes because it is usually impossible to obtain an isothermic mode in such reactors, even for reactions with a relatively low rate of reaction. Plug flow reactors usually operate in adiabatic or intermediate modes, which are far from isothermic even with an external heat removal modification. In can be stated that almost all industrial reactors employed for fast processes are not optimally designed and are therefore ineffective. The quality of products is also far from optimal and the processes are generally not perfect from an engineering, economical, or social point of view (decrease of final product yield and quality, increase of nonrecyclable wastes, excessively high consumption of raw materials and low energy efficiency). 

In this chapter, we applied dimensional analysis to chemical processes. We used homogeneous batch reactions, plug flow reactions, and porous solid—catalyzed reactions as examples. We demonstrated how to derive the dimensionless parameters for these examples, then we showed how to combine them to form the Group I, II, III, and IV Damkohler numbers, as well as the Reynolds number. We demonstrated how these dimensionless parameters and numbers are used during upscaling and downscaling. 

Parallel reactions (nonreacting products) The general case Effect of reaction order One of the reactants undergoes a second reaction Parallel-consecutive reactions Plug-flow reactor with recycle The basic design equation Optimal design of RPR Use of RPR to resolve a selectivity dilemma Semibatch reactors... 

Slow reaction (plug flow) X - Plug fiow characteristics... 

Multiple reactions in parallel producing byproducts. Consider again the system of parallel reactions from Eqs. (2.16) and (2.17). A batch or plug-flow reactor maintains higher average concentrations of feed (Cfeed) than a continuous well-mixed reactor, in which the incoming feed is instantly diluted by the PRODUCT and... 

In general terms, if the reaction to the desired product has a higher order than the byproduct reaction, use a batch or plug-flow reactor. If the reaction to the desired product has a lower order than the byproduct reaction, use a continuous well-mixed reactor. 

The series byproduct reaction requires a plug-flow reactor. Thus, for the mixed parallel and series system above, if... 

But what is the correct choice a byproduct reaction calls for a continuous well-mixed reactor. On the other hand, the byproduct series reaction calls for a plug-flow reactor. It would seem that, given this situation, some level of mixing between a plug-flow and a continuous well-mixed reactor will give the best... 

Polymerization reactions. Polymers are characterized by the distribution of molecular w eight about the mean as well as by the mean itself. The breadth of this distribution depends on whether a batch or plug-flow reactor is used on the one hand or a continuous well-mixed reactor on the other. The breadth has an important influence on the mechanical and other properties of the polymer, and this is an important factor in the choice of reactor. 

Solution We wish to avoid as much as possible the production of di- and triethanolamine, which are formed by series reactions with respect to monoethanolamine. In a continuous well-mixed reactor, part of the monoethanolamine formed in the primary reaction could stay for extended periods, thus increasing its chances of being converted to di- and triethanolamine. The ideal batch or plug-flow arrangement is preferred, to carefully control the residence time in the reactor. 

Another possibility to improve selectivity is to reduce the concentration of monoethanolamine in the reactor by using more than one reactor with intermediate separation of the monoethanolamine. Considering the boiling points of the components given in Table 2.3, then separation by distillation is apparently possible. Unfortunately, repeated distillation operations are likely to be very expensive. Also, there is a market to sell both di- and triethanolamine, even though their value is lower than that of monoethanolamine. Thus, in this case, repeated reaction and separation are probably not justified, and the choice is a single plug-flow reactor. 

Because the characteristic of tubular reactors approximates plug-flow, they are used if careful control of residence time is important, as in the case where there are multiple reactions in series. High surface area to volume ratios are possible, which is an advantage if high rates of heat transfer are required. It is sometimes possible to approach isothermal conditions or a predetermined temperature profile by careful design of the heat transfer arrangements. 

Discussion of the concepts and procedures involved in designing packed gas absorption systems shall first be confined to simple gas absorption processes without compHcations isothermal absorption of a solute from a mixture containing an inert gas into a nonvolatile solvent without chemical reaction. Gas and Hquid are assumed to move through the packing in a plug-flow fashion. Deviations such as nonisotherma1 operation, multicomponent mass transfer effects, and departure from plug flow are treated in later sections. 

In addition to production of simple monofunctional products in hydrocarbon oxidation there are many complex, multifimctional products that are produced by less weU-understood mechanisms. There are also important influences of reactor and reaction types (plug-flow or batch, back-mixed, vapor-phase, Hquid-phase, catalysts, etc). 

Although it appears that methyl ethyl ketone [78-93-3] caimot be the principal product in butane LPO, it has been reported that the ratio of methyl ethyl ketone to acetic acid [64-19-7] can be as high as 3 1 in a plug-flow-type reactor (214). However, this requires a very unusual reactor (length dia = 16, 640 1). The reaction is very unstable and wall reactions may influence mechanisms. 

Fresh butane mixed with recycled gas encounters freshly oxidized catalyst at the bottom of the transport-bed reactor and is oxidized to maleic anhydride and CO during its passage up the reactor. Catalyst densities (80 160 kg/m ) in the transport-bed reactor are substantially lower than the catalyst density in a typical fluidized-bed reactor (480 640 kg/m ) (109). The gas flow pattern in the riser is nearly plug flow which avoids the negative effect of backmixing on reaction selectivity. Reduced catalyst is separated from the reaction products by cyclones and is further stripped of products and reactants in a separate stripping vessel. The reduced catalyst is reoxidized in a separate fluidized-bed oxidizer where the exothermic heat of reaction is removed by steam cods. The rate of reoxidation of the VPO catalyst is slower than the rate of oxidation of butane, and consequently residence times are longer in the oxidizer than in the transport-bed reactor. 

Bubble columns in series have been used to establish the same effective mix of plug-flow and back-mixing behavior required for Hquid-phase oxidation of cyclohexane, as obtained with staged reactors in series. WeU-mixed behavior has been established with both Hquid and air recycle. The choice of one bubble column reactor was motivated by the need to minimize sticky by-products that accumulated on the walls (93). Here, high air rate also increased conversion by eliminating reaction water from the reactor, thus illustrating that the choice of a reactor system need not always be based on compromise, and solutions to production and maintenance problems are complementary. Unlike the Hquid in most bubble columns, Hquid in this reactor was intentionally weU mixed. 

Reactor types modeled A, stoichiometric conversion B, equiUbrium/free-energy minimization, continuous stirred tank, and plug flow C, reactive distillation. Some vendors have special models for special reactions also, private company simulators usually have reactors of specific interest to their company. 

Product Recovery. Comparison of the electrochemical cell to a chemical reactor shows the electrochemical cell to have two general features that impact product recovery. CeU product is usuaUy Uquid, can be aqueous, and is likely to contain electrolyte. In addition, there is a second product from the counter electrode, even if this is only a gas. Electrolyte conservation and purity are usual requirements. Because product separation from the starting material may be difficult, use of reaction to completion is desirable ceUs would be mn batch or plug flow. The water balance over the whole flow sheet needs to be considered, especiaUy for divided ceUs where membranes transport a number of moles of water per Earaday. At the inception of a proposed electroorganic process, the product recovery and refining should be included in the evaluation to determine tme viabUity. Thus early ceU work needs to be carried out with the preferred electrolyte/solvent and conversion. The economic aspects of product recovery strategies have been discussed (89). Some process flow sheets are also available (61). 

Example 5 Percent Approach to Equilibrium For a reversible reaction with rate equation r = L[A — (1 — A)Vl6], the size function kV,./V of a plug flow reactor will be found in terms of percent approach to equilibrium ... 

This is the equation for a plug flow reactor. It can be derived directly from the rate equations with the aid of Laplace transforms. The sequences of second-order reactions of Figs. 7-5n and 7-5c required numerical integrations. 

A reversible reaction A B is conducted in a plug flow reactor. The rate equation is... 

---