Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Processing milling

The BAT for recovered paper processing mills according to EC are the following38 ... [Pg.891]

High-energy processes (milling, lyophilisation, granulating, drying) can introduce certain amounts of amorphicity into otherwise highly crystalline material [20]. As has been previously indicated, enhanced levels of amorphicity lead to increased local levels of moismre, and increased chemical reactivity in these areas. Hancock and Zografi [49] reported on the impact of a roller-compaction process on the water vapour sorption of a sample of aspirin. They speculated that... [Pg.30]

Havlik B, Grafova J, Nycova B. 1968a. Radium-226 liberation from uranium ore processing mill waste solids and uranium rocks into surface streams -1 The effect of different pH of surface waters. Health Phys 14 417-422. [Pg.82]

Waste Reduction In many cases, wastewaters from vegetable oil processing mills are discharged to municipal treatment systems or are treated on-site and... [Pg.2862]

Knudsen HH, Wenzel H, Wagner J, Jepsen SE, Kristensen GH, Mortensen AL, and Ringbaek U. Membrane separation processses in recycling paper processing mills. 5th lAWQ Symposium on Eorest Industry Wastewaters, Vancouver B.C., Canada, June 10-13, 1996, 83-90. [Pg.1006]

In another inventory of various sources of wood wastes in the United States (McKeever, 1995), it was found that for 1991, 26.0 million dry tonnes of bark and 74.5 million dry tonnes of wood residues were generated at primary lumber processing mills. Only 5% of the bark and 6% of the wood residue were wasted and not used. The projection for 1993 based on these findings was that 5.7 million dry tonnes of bark and wood residues were available for recovery and use as an energy resource. The total of 100.5 million dry t/year generated at the mills is about 44% higher than the mill residues found in the Stanford assessment. [Pg.152]

Daily milling Aimual cane processing Milling rate... [Pg.518]

As previously established, particle characterisation has a big impact on downstream processability. Milling is carried out by passing the dried API through a simple pin or air jet mill. If the output from these mills can be monitored, the mill settings can be adjusted and particle characteristics of the mill output changed. [Pg.341]

Rapid prototyping is an "additive process, combining layers of plastic to create a solid object. In contrast, most machining processes (milling, drilling, grinding) are "subtractive processes that remove material from a solid block. [Pg.315]

In practice, however, this seems to be very difficult as a round-robin collaborative work of 12 international researchers shows. Target was to machine a steel sample of AISI 52100 (lOOCrb) in order to get —200 MPa compressive stress at the surface. As processes milling, grinding, turning, fine grinding, and EDM were applied. Only... [Pg.1197]

Barks from 7-8 year old Acacia mangium trees were collected from acacia processing mills in Telaga, Sabah (Malaysia). The Acacia mangium barks were oven dried to 12% moisture content and then chipped into 2-3 cm sized particles. The barks were fiarther ground into fine particles of size 0.5-1 mm using a flaker machine. [Pg.319]

Lancova, K., Hajslova, J., Kostelanska, M., Kohoutkova, J., Nedelnik, J., Moravcova, H., et al. (2008). Fate of trichothecene mycotoxins during processing milling and baking. Food Additives and Contaminants, 25, 650-659. [Pg.404]

Painter, C. A. and Izzo, T. F. Operation of the resin-in-pulp uranium processing mill at Moab, Utah. Proc. 2nd Jnt. Conf. on the Peaceful Uses of Atomic Energy, Geneva, 1958. Paper 500. [Pg.124]


See other pages where Processing milling is mentioned: [Pg.385]    [Pg.274]    [Pg.108]    [Pg.206]    [Pg.385]    [Pg.127]    [Pg.84]    [Pg.139]    [Pg.189]    [Pg.437]    [Pg.445]    [Pg.250]    [Pg.65]    [Pg.393]    [Pg.22]    [Pg.435]    [Pg.4692]    [Pg.385]    [Pg.191]    [Pg.152]    [Pg.1672]    [Pg.2571]    [Pg.550]    [Pg.107]    [Pg.21]    [Pg.163]    [Pg.347]    [Pg.59]    [Pg.196]    [Pg.197]    [Pg.533]    [Pg.465]    [Pg.600]    [Pg.885]    [Pg.63]    [Pg.64]   
See also in sourсe #XX -- [ Pg.100 ]




SEARCH



Active pharmaceutical ingredient milling process

Ball mill process

Ball mill process characteristics

Ball mill process lead oxidation using

Ball milling grinding process

Ball-milling process

Black powder milling process

Chemical milling process

Com wet mill process

Enzymatic corn wet milling process

Interpretation of mill processability

Layer milling process

Manufacturing processes Ball mill process

Mastication and mill processability

Mechanosynthesis process milling

Mill processability

Milling Martin process

Milling Processes and Equipment

Milling acid process

Milling mineral processing

Milling process

Milling process, particle size reduction

Milling schematic process

Milling separation processes

Plutonium processing milling

Processing mill sticking

Production Ball mill process

Science of mill processability

Short flow milling process

Solid mechanochemical milling process

Sugarcane processing milling

The High-Energy Milling Process

Tile processing, milling

Wet milling process

© 2024 chempedia.info