Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

PPG

Caustic Soda. Diaphragm cell caustic is commercially purified by the DH process or the ammonia extraction method offered by PPG and OxyTech (see Fig. 38), essentially involving Hquid—Hquid extraction to reduce the salt and sodium chlorate content (86). Thus 50% caustic comes in contact with ammonia in a countercurrent fashion at 60°C and up to 2500 kPa (25 atm) pressure, the Hquid NH absorbing salt, chlorate, carbonate, water, and some caustic. The overflow from the reactor is stripped of NH, which is then concentrated and returned to the extraction process. The product, about 62% NaOH and devoid of impurities, is stripped free of NH, which is concentrated and recirculated. MetaUic impurities can be reduced to low concentrations by electrolysis employing porous cathodes. The caustic is then freed of Fe, Ni, Pb, and Cu ions, which are deposited on the cathode. [Pg.515]

Pish protein concentrate and soy protein concentrate have been used to prepare a low phenylalanine, high tyrosine peptide for use with phenylketonuria patients (150). The process includes pepsin hydrolysis at pH 1.5 ptonase hydrolysis at pH 6.5 to Hberate aromatic amino acids gel filtration on Sephadex G-15 to remove aromatic amino acids incubation with papain and ethyl esters of L-tyrosine and L-tryptophan, ie, plastein synthesis and ultrafiltration (qv). The plastein has a bland taste and odor and does not contain free amino acids. Yields of 69.3 and 60.9% from PPG and soy protein concentrate, respectively, have been attained. [Pg.471]

PPG Glass Thickness Recommendations to Meet Architects Specified 1-Minute Wind Toad, PPG Industries, Pittsburgh, Pa., 1979. [Pg.529]

Poly(propylene oxide) [25322-69-4] may be abbreviated PPO and copolymers of PO and ethylene oxide (EO) are referred to as EOPO. Diol poly(propylene oxide) is commonly referred to by the common name poly(propylene glycol) (PPG). Propylene oxide [75-56-9] and poly(propylene oxide) and its copolymers, with ethylene oxide, have by far the largest volume and importance in the polyurethane (PUR) and surfactant industry compared to all other polyepoxides. Articles reviewing propylene oxide (1), poly(propylene oxide) (2—4), other poly(aIkylene oxides) (4), and polyurethanes (5—7) are cited to lead the interested reader to additional detail not in the scope of this article. [Pg.348]

Each company has a full line of products including PPG (diols) and glycerol adducts, as well as other initiator adducts. [Pg.353]

Refractive Index. The effect of mol wt (1400-4000) on the refractive index (RI) increment of PPG in ben2ene has been measured (167). The RI increments of polyglycols containing aUphatic ether moieties are negative drj/dc (mL/g) = —0.055. A plot of RI vs 1/Af is linear and approaches the value for PO itself (109). The RI, density, and viscosity of PPG—salt complexes, which maybe useful as polymer electrolytes in batteries and fuel cells have been measured (168). The variation of RI with temperature and salt concentration was measured for complexes formed with PPG and some sodium and lithium salts. Generally, the RI decreases with temperature, with the rate of change increasing as the concentration increases. [Pg.354]

The composition of PPG—PEG blends has been determined using gpc with coupled density and RI detectors. PEG and PPG have different response factors for the density and RI detectors which were exploited (173). An hplc system with CHROMPAC RP-18C2g column at 298°C and acetonitrile—water or methanol—water as the mobile phase has been used to gather information about the functionaUty of PPO (174). [Pg.354]

Reversed-phase hplc has been used to separate PPG into its components using evaporative light scattering and uv detection of their 3,5-dinitroben2oyl derivatives. Acetonitrile—water or methanol—water mixtures effected the separation (175). Polymer glycols in PUR elastomers have been identified (176) by pyrolysis-gc. The pyrolysis was carried out at 600°C and produced a small amount of ethane, CO2, propane, and mostiy propylene, CO, and CH4. The species responsible for a musty odor present in some PUR foam was separated and identified by gc (Supelco SP-2100 capillary column)... [Pg.354]

Mass Spectrometry. Field desorption mass spectrometry has been used to analy2e PPO (179). Average molecular weight parameters (M and could be determined using either protonated (MH + ) or cation attachment (MNa + ) ions. Good agreement was found between fdms and data supphed by the manufacturer, usually less than 5% difference in all cases up to about 3000 amu. Laser desorption Fourier transform mass spectrometry was used to measure PPG ion and it was claimed that ions up to m/2 9700 (PEG) can be analy2ed by this method (180). [Pg.354]


See other pages where PPG is mentioned: [Pg.529]    [Pg.793]    [Pg.807]    [Pg.807]    [Pg.807]    [Pg.480]    [Pg.490]    [Pg.520]    [Pg.149]    [Pg.294]    [Pg.294]    [Pg.389]    [Pg.390]    [Pg.390]    [Pg.391]    [Pg.391]    [Pg.391]    [Pg.308]    [Pg.309]    [Pg.312]    [Pg.315]    [Pg.316]    [Pg.317]    [Pg.363]    [Pg.426]    [Pg.427]    [Pg.482]    [Pg.367]    [Pg.524]    [Pg.528]    [Pg.89]    [Pg.170]    [Pg.506]    [Pg.198]    [Pg.309]    [Pg.310]    [Pg.278]    [Pg.323]    [Pg.323]    [Pg.353]    [Pg.353]    [Pg.354]   
See also in sourсe #XX -- [ Pg.188 , Pg.191 ]

See also in sourсe #XX -- [ Pg.798 ]




SEARCH



PPG Industries

PPG Industries Inc

PPG Industries Ohio, Inc

PPG Industries. USA

PPG Products

PPG polyols

PPG process

PPG, calibrant

PPG-silica suspensions

Phosphate PPG

Polypropylene Glycol (PPG)

Processability and Property Latitude of Elastomers Based on Ultra-Low Monol PPG Polyols

Ultra-Low Monol PPG High-Performance Polyether Polyols for Polyurethanes

© 2024 chempedia.info