Polymerization glue

A. Estimating the Volume Increase during Polymerization. Glue one end of a toilet paper or paper towel roll onto a piece of paper or cardboard so that the roll stands upright on the paper base. Use enough glue so that the bottom of the roll is sealed to the base. Place the cylinder/base on newspaper or paper toweling. 

Three kinds of glues or adhesives can be distinguished melt glues, solution glues, and polymerization glues. Elastomers, elastoplasts, or thermosets may be used in all three kinds. 

Cyanoacrylate adhesives (Super-Glues) are materials which rapidly polymerize at room temperature. The standard monomer for a cyanoacrylate adhesive is ethyl 2-cyanoacrylate [7085-85-0], which readily undergoes anionic polymerization. Very rapid cure of these materials has made them widely used in the electronics industry for speaker magnet mounting, as weU as for wire tacking and other apphcations requiring rapid assembly. Anionic polymerization of a cyanoacrylate adhesive is normally initiated by water. Therefore, atmospheric humidity or the surface moisture content must be at a certain level for polymerization to take place. These adhesives are not cross-linked as are the surface-activated acryhcs. Rather, the cyanoacrylate material is a thermoplastic, and thus, the adhesives typically have poor temperature resistance. 

Emulsion Adhesives. The most widely used emulsion-based adhesive is that based upon poly(vinyl acetate)—poly(vinyl alcohol) copolymers formed by free-radical polymerization in an emulsion system. Poly(vinyl alcohol) is typically formed by hydrolysis of the poly(vinyl acetate). The properties of the emulsion are derived from the polymer employed in the polymerization as weU as from the system used to emulsify the polymer in water. The emulsion is stabilized by a combination of a surfactant plus a coUoid protection system. The protective coUoids are similar to those used paint (qv) to stabilize latex. For poly(vinyl acetate), the protective coUoids are isolated from natural gums and ceUulosic resins (carboxymethylceUulose or hydroxyethjdceUulose). The hydroHzed polymer may also be used. The physical properties of the poly(vinyl acetate) polymer can be modified by changing the co-monomer used in the polymerization. Any material which is free-radically active and participates in an emulsion polymerization can be employed. Plasticizers (qv), tackifiers, viscosity modifiers, solvents (added to coalesce the emulsion particles), fillers, humectants, and other materials are often added to the adhesive to meet specifications for the intended appHcation. Because the presence of foam in the bond line could decrease performance of the adhesion joint, agents that control the amount of air entrapped in an adhesive bond must be added. Biocides are also necessary many of the materials that are used to stabilize poly(vinyl acetate) emulsions are natural products. Poly(vinyl acetate) adhesives known as "white glue" or "carpenter s glue" are available under a number of different trade names. AppHcations are found mosdy in the area of adhesion to paper and wood (see Vinyl polymers). 

Adhesives based on isocyanate (especially PMDl, polymethylene diisocyanate, more exactly polymeric 4,4 -diphenylmethane diisocyanate) have been used for more than 25 years in the wood-based panel industry [88], but still have a low market value in the wood-working industry compared to systems based on UF-, MUF- or PF-resins. The main application is the production of waterproof panels, but also the production of panels from raw materials that are difficult to glue, like straw, bagasse, rice shells or sugar cane bagasse. They can be used as adhesives for wood-based products like particleboard, oriented strandboard (OSB), laminated strand lumber (LSL), medium-density fiberboard (MDF) or... 

Polyurethane adhesives are formed by the reaction of various types of isoeyanates with polyols. The polar urethane group enables adhesion to various surfaees. Depending on the raw materials, glue lines with rubber-like elastic to brittle-hard behavior ean be aehieved. The presence of reactive terminal groups provides a ehemieally hardened adhesive. When polymerized to a high enough molecular weight, the adhesive ean be physically rather than chemically hardened, i.e. a hot melt. 

Dunky, M., Urea-formaldehyde glue resins. In Salamone, J.C. (Ed.), Polymeric Materials Encyclopedia, Vol. 11. CRC Press, Boca Raton, FL, 1996. 

A number of different glues were utilized on early aircraft. Since these craft were manufactured during the infancy of synthetic polymeric chemistry, all were of natural origin. These glues are still in use today, though not for aerospace bonding. 

Uses of Formaldehyde. Formaldehyde is the simplest and most reactive aldehyde. Condensation polymerization of formaldehyde with phenol, urea, or melamine produces phenol-formaldehyde, urea formaldehyde, and melamine formaldehyde resins, respectively. These are important glues used in producing particle hoard and plywood. 

Cyanoacrylate adhesives, the famous consumer Super glue , is a monomer that polymerizes when it comes in contact with moisture, even with atmospheric moisture. 

Polymers are also used as sutures. Fighters and other athletes have used poly(alpha-cyanoacrylates), super glues, to quickly stop blood flow in surface cuts. Today, super glue is also used for, in place of or along with, more traditional polymeric suture threads for selected surface wounds, internal surgery, and retinal and corneal surgery. The alpha-cyanoacrylate polymers (structure 19.22) undergo anionic polymerization in the presence of water. More about sutures is explained in Section 19.6. 

Adhesives are used in everyday applications. Adhesives may be in liquid form or thick pastes. Their main mechanism is based on the polymerization or crosslinking of polymers, which gives rise to glue or other adhesive application. The degree of adhesion of such a process is determined by conventional technological tests. 

Viscosity of Polymer Solutions. Polymer solutions are very common. Glues, pastes, and paints are just a few examples of commercially available aqueous suspensions of organic macromolecules. Also, recall from Chapter 3 that certain types of polymerization reactions are carried out in solution to assist in heat removal. The resulting polymers are also in solution, and their behavior must be fully understand in order to properly transport them and effect solvent removal, if necessary. 

Alkyl-2-cyanoacrylates are readily polymerized in the presence of weak bases such as water. Because of the presence of the strong polar cyano pendant group these polymers (e.g. Super Glue) are excellent adhesives. Polybutyl-2-cyanoacrylate is tolerated by the body better than its lower alkyl homo-logues. Hence polybutyl-2-cyanoacrylate is used as an adhesive aid to stop bleeding in some surgical operations. 

Many dialkyl and diaryl cadmium compounds have found use as polymerization catalysts. For example, the diethyl compound catalyzes polymerization of vinyl chloride, vinyl acetate, and methyl methacrylate (45), and when mixed with TiCl can be used to produce polyethylene and crystalline polypropylene for filaments, textiles, glues, and coatings (45). With >50% TiCl diethyl cadmium polymerizes dienes. Diethyl cadmium maybe used as an intermediate ethylating agent in the production of tetraethyllead. The diaryl compounds such as diphenylcadmium [2674-04-6]> (C H Cd, (mp 174°C) are also polymerization catalysts. These compounds are also prepared using Grignard or arylUthium reagents in tetrahydrofiiran (THF) solvent but may be prepared by direct metal substitution reactions such as ... 

Emulsion Adhesives The most widely used emulsion-based adhesive is that based upon poly(vinyl acetate)-poly(vinyl alcohol) copolymers formed by free-radical polymerization in an emulsion system. Poly(vinyl alcohol) is typically formed by hydrolysis of the poly(vmyl acetate). This is also known as white glue. ... 

---