Poly changes

As a furtlier example for tire meaning of ex situ investigations of emersed electrodes witli surface analytical teclmiques, results obtained for tire double layer on poly crystalline silver in alkaline solutions are presented in figure C2.10.3. This system is of scientific interest, since tliin silver oxide overlayers (tliickness up to about 5 nm) are fonned for sufficiently anodic potentials, which implies tliat tire adsorjDtion of anions, cations and water can be studied on tire clean metal as well as on an oxide covered surface [55, 56]. For tire latter situation, a changed... 

Materials that typify thermoresponsive behavior are polyethylene—poly (ethylene glycol) copolymers that are used to functionalize the surfaces of polyethylene films (smart surfaces) (20). When the copolymer is immersed in water, the poly(ethylene glycol) functionaUties at the surfaces have solvation behavior similar to poly(ethylene glycol) itself. The abiUty to design a smart surface in these cases is based on the observed behavior of inverse temperature-dependent solubiUty of poly(alkene oxide)s in water. The behavior is used to produce surface-modified polymers that reversibly change their hydrophilicity and solvation with changes in temperatures. Similar behaviors have been observed as a function of changes in pH (21—24). 

Other examples of materials that respond smartly to changes in temperature are the poly(ethylene glycol)s-modifted cottons, polyesters, and... 

Emulsion Adhesives. The most widely used emulsion-based adhesive is that based upon poly(vinyl acetate)—poly(vinyl alcohol) copolymers formed by free-radical polymerization in an emulsion system. Poly(vinyl alcohol) is typically formed by hydrolysis of the poly(vinyl acetate). The properties of the emulsion are derived from the polymer employed in the polymerization as weU as from the system used to emulsify the polymer in water. The emulsion is stabilized by a combination of a surfactant plus a coUoid protection system. The protective coUoids are similar to those used paint (qv) to stabilize latex. For poly(vinyl acetate), the protective coUoids are isolated from natural gums and ceUulosic resins (carboxymethylceUulose or hydroxyethjdceUulose). The hydroHzed polymer may also be used. The physical properties of the poly(vinyl acetate) polymer can be modified by changing the co-monomer used in the polymerization. Any material which is free-radically active and participates in an emulsion polymerization can be employed. Plasticizers (qv), tackifiers, viscosity modifiers, solvents (added to coalesce the emulsion particles), fillers, humectants, and other materials are often added to the adhesive to meet specifications for the intended appHcation. Because the presence of foam in the bond line could decrease performance of the adhesion joint, agents that control the amount of air entrapped in an adhesive bond must be added. Biocides are also necessary many of the materials that are used to stabilize poly(vinyl acetate) emulsions are natural products. Poly(vinyl acetate) adhesives known as "white glue" or "carpenter s glue" are available under a number of different trade names. AppHcations are found mosdy in the area of adhesion to paper and wood (see Vinyl polymers). 

Sulfonation has been used to change some characteristics of blends. Poly(2,6-diphenyl-l,4-phenylene oxide) and polystyrene are immiscible. However, when the polymers were functionalized by sulfonation, even though they remained immiscible when blended, the functionalization increased interfacial interactions and resulted in improved properties (65). In the case of DMPPO and poly(ethyl acrylate) the originally immiscible blends showed increased miscibility with sulfonation (66). 

Commercial Hydrolysis Process. The process of converting poly(vinyl acetate) to poly(vinyl alcohol) on a commercial scale is compHcated on account of the significant physical changes that accompany the conversion. The viscosity of the poly(vinyl acetate) solution increases rapidly as the conversion proceeds, because the resulting poly(vinyl alcohol) is insoluble in the most common solvents used for the polymeri2ation of vinyl acetate. The outcome is the formation of a gel swollen with the resulting acetic acid ester and the alcohol used to effect the transesterification. 

In the slurry process, the hydrolysis is accompHshed using two stirred-tank reactors in series (266). Solutions of poly(vinyl acetate) and catalyst are continuously added to the first reactor, where 90% of the conversion occur, and then transferred to the second reactor to reach hiU conversion. Alkyl acetate and alcohols are continuously distilled off in order to drive the equiUbrium of the reaction. The resulting poly(vinyl alcohol) particles tend to be very fine, resulting in a dusty product. The process has been modified to yield a less dusty product through process changes (267,268) and the use of additives (269). Partially hydroly2ed products having a narrow hydrolysis distribution cannot be prepared by this method. 

---