Poly block copolymer with

All these elastomers, especially poly(ethylene- (9-butylene) and poly(ethylene- (9-propylene), are nonpolar. The corresponding block copolymers can thus be compounded with hydrocarbon-based extending oils, but do not have much oil resistance. Conversely, block copolymers with polar polyester or polyether elastomer segments have Htde affinity for such hydrocarbon oils and so have better oil resistance. 

The poly(styrene-b-isoprene) (P(S-b-IP)) and poly(-styrene-b-2-vinyl pyridine) (P(S-b-2VP)) block copolymers with narrow molecular weight distributions for blending with the microspheres were also synthesized using the additional anionic polymerization technique. The number-average molecular weights (Mns) and PS contents are also shown in Table 1. 

When ACPC was condensed with hexamethylene diamine in the presence of two other acid chlorides (seb-acoyl or adipoyl chloride), poly(amide)s 6.6 and 6.10 with various numbers of azo groups per repeating unit (between 0.14 and 1.0, depending on the ratio of the acid chlorides used) could be obtained [35,36]. Thus, block copolymers with a controlled segment length of the poly-(amide) blocks were attainable. 

Figure 7 shows the results of measurements of adsorption density by Parsonage, etal. [77] on a series of eighteen block copolymers, with poly(2-vinylpyridine) [PVP] anchors and polystyrene [PS] buoys, adsorbed from toluene (selective for PS) of variable molecular weight in each block. The results are presented as the reciprocal square of Eq. 28, that is, as a dimensionless number density of chains ct (d/Rg A)-2. For all but the copolymers of highest asymmetry, Eq. 28 is in good agreement with the data of Fig. 7. The high asymmetry copolymers are in the regime of the data of curves (a) and (c) of Fig. 3 where the large relative size...

Anionic polymerization of lactams was shown to proceed according to what is called the activated monomer mechanism. With bischloroformates of hydroxy-terminated poly(tetramethyleneglycol) and poly(styrene glycol) as precursors for a polymeric initiator containing N-acyl lactam ends, block copolymers with n-pyrrol-idone and e-caprolactam were obtained by bulk polymerizations in vacuum at 30 and 80 °C, respectively361. ... 

Among the many unusual properties that the arborescent architecture leads to, most notable is the discovery that block copolymers with a high MW dendritic (arborescent) polyisobutylene core and poly(para-methylstyrene) end blocks can manifest themselves either as a rubber, or as a plastic, depending on their environment (Figures 7.16 and 7.17). The behavior is thermally irreversible. 

Block copolymers with PS and a polymethacrylate block carrying a liquid crystalline group, PS-b-poly 6-[4-(cyanophenylazo)phenoxy]hexyl methacrylate, were successfully prepared in quantitative yields and with relatively narrow molecular weight distributions (Scheme 5) [18]. The thermotropic liquid crystalline behavior of the copolymers was studied by differential scanning calorimetry. 

GTP was employed for the synthesis of block copolymers with the first block PDMAEMA and the second PDEAEMA, poly[2-(diisopropylamino)e-thyl methacrylate], PDIPAEMA or poly[2-(N-morpholino)ethyl methacrylate], PM EM A (Scheme 33) [87]. The reactions took place under an inert atmosphere in THF at room temperature with l-methoxy-l-trimethylsiloxy-2-methyl-1-propane, MTS, as the initiator and tetra-n-butyl ammonium bibenzoate, TBABB, as the catalyst. Little or no homopolymer contamination was evidenced by SEC analysis. Copolymers in high yields with controlled molecular weights and narrow molecular weight distributions were obtained in all cases. The micellar properties of these materials were studied in aqueous solutions. 

Hyperbranched polymers have also been prepared via living anionic polymerization. The reaction of poly(4-methylstyrene)-fo-polystyrene lithium with a small amount of divinylbenzene, afforded a star-block copolymer with 4-methylstyrene units in the periphery [200]. The methyl groups were subsequently metalated with s-butyllithium/tetramethylethylenediamine. The produced anions initiated the polymerization of a-methylstyrene (Scheme 109). From the radius of gyration to hydrodynamic radius ratio (0.96-1.1) it was concluded that the second generation polymers behaved like soft spheres. 

ABA-type triblock copolymerization of MMA/BuA/MMA should give rubberlike elastic polymers. The resulting copolymers should have two vitreous outer blocks, where the poly(MMA) moiety (hard segment) associates with the nodules, and the central soft poly(BuA) elastomeric block provides rubber elasticity. Ihara et al. [35] were the first to synthesize an AB-type block copolymer, with MMA (190 equivalents of initiator) first polymerized by... 

They also synthesized polymeric iniferters containing the disulfide moiety in the main chain [149,150]. As shown in Eq. (30),polyphosphonamide,which was prepared by the polycondensation reaction of phenyl phosphoric dichloride with piperadine, was allowed to react with carbon disulfide in the presence of triethylamine, followed by oxidative coupling to yield the polymeric iniferter 32. These polymeric iniferters were used for the synthesis of block copolymers with St or MMA, with the composition and block lengths controlled by the ratio of the concentration of the polymeric iniferter to the monomer or by conversion. The block copolymers of polyphosphonamide with poly(St) or poly(MMA) were found to have improved flame resistance characteristics. 

The living radical polymerization of some derivatives of St was carried out. The polymerizations of 4-bromostyrene [254], 4-chloromethylstyrene [255, 256], and other derivatives [257] proceed by a living radical polymerization mechanism to give polymers with well-controlled structures and block copolymers with poly(St). The random copolymerization of St with other vinyl... 

As the final products— polystyrene-Zi-poly(vinylperfluorooctanoic ester)— form micelles in tetrahydrofuran (THF) as well as in DMF, there are not direct GPC data to characterize molecular parameter. For this reason, we employed esterification of the hydroxylated block copolymers with benzoylchloride as a model reaction to obtain a comparable product with molecular solubility that can easily be characterized by DMF-GPC. The GPC data from PSB-II—our largest and therefore most sensitive block copolymer—are summarized in Table 10.2. Results for all the other polymers are similar. 

A. Mayer et al. examined poly(dimethylsiloxane)-bIock-poly(ethylene oxide) (PDMS-b-PEO), poly(styrene)-f)Iock-poly(ethylene oxide) (PS-b-PEO), polystyrene-block-poly(methacryhc acid) (PS-b-PMAA) as amphiphihc block copolymers with regard to their properties in stabilizing colloidal metal nanoparticles [37, 49]. All three polymers are successfully used to stabihze various transition metal coUoids... 

Polyurethane block copolymer with polyether/polyester Poly(vinyl alcohol)... 

Ekin A, Webster DC. (2006) Synthesis and characterization of novel hydroxyalkyl carbamate and dihydroxyalkyl carbamate terminated poly(dimethylsiloxane) oligomers and their block copolymers with poly(e-caprolactone). Macromolecules 39 8659-8668... 

The temperature optimization for the RAFT polymerization of EAA revealed an optimum reaction temperature of 70 °C. Block copolymers with a poly(methyl acrylate) (PMA), a poly(n-butyl acrylate) (PnBA), a PMMA, or a poly(A,A-dimethyl aminoethyl methacrylate) (PDMAEMA) first block and a poly(l-ethoxyethyl acrylate) (PEEA) second block were successfully synthesized in an automated synthesizer. The synthesis robot was employed for the preparation of 16 block copolymers consisting of 25 units of the first block composed of PMA (exp. 1 ), PnBA (exp. 5-8), PMMA (exp. 9-13), and PDMAEMA (exp. 13-16) and a second block of PEEA consisting of 25, 50, 75, or 100 units, respectively. The first blocks were polymerized for 3 h and a sample from each reaction was withdrawn for SEC analysis. Subsequently, EAA was added and the reactions were continued for 12 h. The molar masses and PDI values of the obtained block copolymers are shown in Fig. 15. 

Gohy JE, Lohmeijer BGG, Alexeev A, Wang XS, Manners 1, Winnik MA, Schubert US (2004) Cylindrical micelles from the aqueous self-assembly of an amphiphilic poly(ethylene oxide)-b-poly(ferrocenylsilane) (PEO-b-PES) block copolymer with a metallo-supramolecular linker at the block junction. Chem Eur J 20 4315 323... 

Mahmud A, Xiong X-B, Lavasanifar A (2006) Novel self-associating poly(ethylene oxide)-block-poly(E-caprolactone) block copolymers with functional side groups on the polyester block for drug delivery. Macromolecules 39 9414-9428... 

Harada A, Kataoka K. Formation of polyion complex micelles in an aqueous milieu from a pair of oppositely-charged block copolymers with poly(ethylene glycol) segments. Macromolecules 1995 28 5294-5299. 

Ceresa (78,79) studied in detail the system poly(methyl methacrylate)-acrylonitrile. Figure 25 shows the change in composition with mastication time. A study of gel formation by the block copolymers was made by subjecting the isolated fractions of block copolymers to further mastication. A wide range of block copolymers with varying composition and structure was obtained (Fig. 26). 

The living nature of the poly(styryl)anion allows one to prepare block copolymers with a great deal of control of the block copolymer structure. The preparation of diblock, triblock, and other types of multiblock copolymers has been reviewed [29-32]. Several of these block copolymers are in commercial use. The basic concept involves first preparing polystyrene block [RSt StLi—see Eq. (2)] and then adding a new monomer that can be added to start another growing segment. 

---