Platinum mechanism

The mechanism for CO oxidation over platinum group metals has been established from a wealth of data, the analysis of which is beyond the scope of this chapter. It is quite evident that surface science provided the foundation for this mechanism by directly showing that CO adsorbs molecularly and O2 adsorbs... 

A pletliora of different SA systems have been reported in tire literature. Examples include organosilanes on hydroxylated surfaces, alkanetliiols on gold, silver, copper and platinum, dialkyl disulphides on gold, alcohols and amines on platinum and carboxyl acids on aluminium oxide and silver. Some examples and references can be found in [123]. More recently also phosphonic and phosphoric esters on aluminium oxides have been reported [124, 125]. Only a small selection out of tliis number of SA systems can be presented here and properties such as kinetics, tliennal, chemical and mechanical stability are briefly presented for alkanetliiols on gold as an example. 

Method A. Cool a solution of the nitrate-free dichloride, prepared from or equivalent to 5 0 g. of palladium or platinum, in 50 ml. of water and 5 ml. of concentrated hydrochloric acid in a freezing mixture, and treat it with 50 ml. of formahn (40 per cent, formaldehyde) and 11 g. of the carrier (charcoal or asbestos). Stir the mixture mechanically and add a solution of 50 g. of potassium hydroxide in 50 ml. of water, keeping the temperature below 5°. When the addition is complete, raise the temperature to 60° for 15 minutes. Wash the catalyst thoroughly by decantation with water and finally with dilute acetic acid, collect on a suction filter, and wash with hot water until free from chloride or alkali. Dry at 100° and store in a desiccator. 

Dentistry. Most casting alloys meet the composition and properties criteria of specification no. 5 of the American Dental Association (37) which prescribes four types of alloy systems constituted of gold—silver—copper with addition of platinum, palladium, and 2inc. Composition ranges are specified, as are mechanical properties and minimum fusion temperatures. Wrought alloys for plates also may include the same constituents. Similarly, specification no. 7 prescribes nickel and two types of alloys for dental wires with the same alloy constituents (see Dental materials). 

Niobium is used as a substrate for platinum in impressed-current cathodic protection anodes because of its high anodic breakdown potential (100 V in seawater), good mechanical properties, good electrical conductivity, and the formation of an adherent passive oxide film when it is anodized. Other uses for niobium metal are in vacuum tubes, high pressure sodium vapor lamps, and in the manufacture of catalysts. 

The standard potential for the anodic reaction is 1.19 V, close to that of 1.228 V for water oxidation. In order to minimize the oxygen production from water oxidation, the cell is operated at a high potential that requires either platinum-coated or lead dioxide anodes. Various mechanisms have been proposed for the formation of perchlorates at the anode, including the discharge of chlorate ion to chlorate radical (87—89), the formation of active oxygen and subsequent formation of perchlorate (90), and the mass-transfer-controUed reaction of chlorate with adsorbed oxygen at the anode (91—93). Sodium dichromate is added to the electrolyte ia platinum anode cells to inhibit the reduction of perchlorates at the cathode. Sodium fluoride is used in the lead dioxide anode cells to improve current efficiency. 

Physical and Mechanical Properties. Whereas there are some similarities in the physical and chemical properties between corresponding members of the PGM triads, eg, platinum and palladium, the PGMs taken as a unit exhibit a wide range of properties (2). Some of the most important are summarized in Table 2. 

Hardness of the aimealed metals covers a wide range. Rhodium (up to 40%), iridium (up to 30%), and mthenium (up to 10%) are often used to harden platinum and palladium whose intrinsic hardness and tensile strength are too low for many intended appHcations. Many of the properties of rhodium and indium. Group 9 metals, are intermediate between those of Group 8 and Group 10. The mechanical and many other properties of the PGMs depend on the physical form, history, and purity of a particular metal sample. For example, electrodeposited platinum is much harder than wrought metal. 

Hydrosdylation can also be initiated by a free-radical mechanism (227—229). A photochemical route uses photosensitizers such as peresters to generate radicals in the system. Unfortunately, the reaction is quite sluggish. In several apphcations, radiation is used in combination with platinum and an inhibitor to cure via hydro sdylation (230—232). The inhibitor is either destroyed or deactivated by uv radiation. 

The catalysts with the simplest compositions are pure metals, and the metals that have the simplest and most uniform surface stmctures are single crystals. Researchers have done many experiments with metal single crystals in ultrahigh vacuum chambers so that unimpeded beams of particles and radiation can be used to probe them. These surface science experiments have led to fundamental understanding of the stmctures of simple adsorbed species, such as CO, H, and small hydrocarbons, and the mechanisms of their reactions (42) they indicate that catalytic activity is often sensitive to small changes in surface stmcture. For example, paraffin hydrogenolysis reactions take place rapidly on steps and kinks of platinum surfaces but only very slowly on flat planes however, hydrogenation of olefins takes place at approximately the same rate on each kind of surface site. 

Silicon—Ca.rbon Thermoset. The Sycar resins of Hercules are sihcon—carbon thermosets cured through the hydrosilation of sihcon hydride and sihcon vinyl groups with a trace amount of platinum catalyst. The material is a fast-cure system (<15 min at 180°C) and shows low moisture absorption that outperforms conventional thermosets such as polyimides and epoxies. Furthermore, the Sycar material provides excellent mechanical and physical properties used in printed wiring board (PWB) laminates and encapsulants such as flow coatable or glob-top coating of chip-on-board type apphcations. 

Metals and alloys, the principal industrial metalhc catalysts, are found in periodic group TII, which are transition elements with almost-completed 3d, 4d, and 5d electronic orbits. According to theory, electrons from adsorbed molecules can fill the vacancies in the incomplete shells and thus make a chemical bond. What happens subsequently depends on the operating conditions. Platinum, palladium, and nickel form both hydrides and oxides they are effective in hydrogenation (vegetable oils) and oxidation (ammonia or sulfur dioxide). Alloys do not always have catalytic properties intermediate between those of the component metals, since the surface condition may be different from the bulk and catalysis is a function of the surface condition. Addition of some rhenium to Pt/AlgO permits the use of lower temperatures and slows the deactivation rate. The mechanism of catalysis by alloys is still controversial in many instances. 

It is stated that in time the acidity (up to 2,5 units) of 0,1-1,0 M HMTA aqueous solutions changes maximally at 1°C, in comparatively to other temperatures (11, 16, 21°C). When the temperature arises the change of HMTA aqueous solutions pH values decreases in time. Formaldehyde and ammonium ions (end products of HMTA hydrolysis) have been fixed only in more diluted solutions (0,10 and 0,25M). The concentration of NH in them in some times is higher than H2C=0 concentration that is caused by oxidation of the last one to a formic acid, being accompanied by the change of the system platinum electrode potential. It is stated that concentration NH in solutions does not exceed 5% from HMTA general content. The conclusion the mechanism of HMTA destruction in H,0 to depend essentially on its concentration and temperature has been made. 

Stratifying water systems for selective extraction of thiocyanate complexes of platinum metals have been proposed. The extraction degree of mthenium(III) by ethyl and isopropyl alcohols, acetone, polyethylene glycol in optimum conditions amounts to 95-100%. By the help of electronic methods, IR-spectroscopy, equilibrium shift the extractive mechanism has been proposed and stmctures of extractable compounds, which contain single anddouble-chai-ged acidocomplexes [Rh(SCN)J-, [Ru(SCN)J, [Ru(SCN)J -have been determined. Constants of extraction for associates investigated have been calculated. 

Processes, other than wet processes, in which metal articles (other than gold, platinum or iridium) are ground, abraded or polished using mechanical power, in any room for more than 12 hours per week 6 months... 

---