Phenyl cellulosics

Arosol Emerescence 1160-, ethyleneglycol monophenyl ether p-hydroxyethyl phenyl ether l-hydroxy-2-phenoxyethane Phenoxen p-phenoxyethyl alcohol phenyl cellulose. 

The acetyl content of cellulose acetate may be calculated by difference from the hydroxyl content, which is usually determined by carbanilation of the ester hydroxy groups in pyridine solvent with phenyl isocyanate [103-71-9J, followed by measurement of uv absorption of the combined carbanilate. Methods for determining cellulose ester hydroxyl content by near-infrared spectroscopy (111) and acid content by nmr spectroscopy (112) and pyrolysis gas chromatography (113) have been reported. 

However, this method is appHed only when esterification cannot be effected by the usual acid—alcohol reaction because of the higher cost of the anhydrides. The production of cellulose acetate (see Fibers, cellulose esters), phenyl acetate (used in acetaminophen production), and aspirin (acetylsahcyhc acid) (see Salicylic acid) are examples of the large-scale use of acetic anhydride. The speed of acylation is greatiy increased by the use of catalysts (68) such as sulfuric acid, perchloric acid, trifluoroacetic acid, phosphoms pentoxide, 2inc chloride, ferric chloride, sodium acetate, and tertiary amines, eg, 4-dimethylaminopyridine. 

The potential for use of chiral natural materials such as cellulose for separation of enantiomers has long been recognized, but development of efficient materials occurred relatively recently. Several acylated derivatives of cellulose are effective chiral stationary phases. Benzoate esters and aryl carbamates are particularly useful. These materials are commercially available on a silica support and imder the trademark Chiralcel. Figure 2.4 shows the resolution of y-phenyl-y-butyrolactone with the use of acetylated cellulose as the adsorbent material. 

UV absorbers have been found to be quite effective for stabilization of polymers and are very much in demand. They function by the absorption and harmless dissipation of the sunlight or UV-rich artificial radiation, which would have otherwise initiated degradation of a polymer material. Meyer and Geurhart reported, for the first time in 1945 [10], the use of UV absorber in a polymer. They found that the outdoor life of cellulose acetate film was greatly prolonged by adding phenyl salicylate (salol) [10]. After that, resorcinol monobenzoate, a much more effective absorber, was introduced in 1951 [11] for stabilization of PP, but salol continued to be the only important commercial stabilizer for several years. The 2,4-dihydroxybenzophenone was marketed in 1953, followed shortly by 2-hydroxy-4-methoxybenzophenone and other derivatives. Of the more commonly known UV absorbers, the 2-hydroxybenzophenones, 2-hy-droxy-phenyl-triazines, derivatives of phenol salicylates, its metal chelates, and hindered amine light stabilizers (HALS) are widely used in the polymer industry. 

Photo-induced grafting onto wood cellulose with several vinyl monomers using phenyl acetophenone and benzophenone derivatives as photosensitizers has been reported [72]. A fast increase in grafting was observed for short irradiation times, whereas longer ones resulted in a decreased percent grafting. 

By the treatment of oat spelt xylan with phenyl or tolyl isocyanate in pyridine the fully fimctionahzed corresponding carbamates were prepared [416]. Xylan 3,5-dimethylphenylcarbamate showed higher recognition abihty for chiral drugs compared to that of the same cellulose derivative [417]. 

The butyrate substituents are larger than those for other polymers listed, but they are not proportionately larger than the exceptional length of the structural unit of cellulose. An inspection of models shows that the three butyrate units can be accommodated about the cellulose ring with less obstruction than for the phenyl groups of polystyrene, for example. 

FIGURE 2.19 Comparison of the concentration profiles of 5-phenyl-f-pentanol (dashed line) and benzophenone (thin solid line) developed as single analytes and as a binary mixture (bold solid line) concentration of 5-phenyl-1-pentanol in the sample was 1.50 mol 1" and that of benzophenone was 0.10 mol 1" . Microcrystalline cellulose was used as stationary phase and -octane as mobile phase [26]. 

Okamoto et al [85] performed the optical resolution of primaquine and other racemic drugs by high performance liquid chromatography using cellulose and amylose tris-(phenylcarbamate) derivatives as chiral stationary phases. Primaquine and other compounds were effectively resolved by cellulose and/or amylose derivatives having substituents such as methyl, tertiary butyl, or halogen, on the phenyl groups. 

In a typical experiment the isocyanate (0.006 moles) was reacted with 1.5 g of the polysaccharide in 150 ml of a 5% LiCl/ N,N-dimethylacetamide solution at 90°C under nitrogen for two hours. The appearance of a strong infrared absorbance at 1705 cm l was an indication of carbamate formation. The derivatized polymer was isolated as a white powder by precipitation of the reaction solution into a nonsolvent such as methanol. Alternatively thin films were cast directly from solution the lithium salt could be removed by rinsing with acetone. Figure 1 illustrates the reaction of cellulose with phenyl isocyanate. 

The phase transfer catalyzed alkylation reaction of dodecyl phenyl glycidyl ether (DPGE) with hydroxyethyl cellulose (HEC) was studied as a mechanistic model for the general PTC reaction with cellulose ethers. In this way, the most effective phase transfer catalysts and optimum reaction concentrations could be identified. As a model cellulose ether, CELLOSIZE HEC11 was chosen, and the phase transfer catalysts chosen for evaluation were aqueous solutions of choline hydroxide, tetramethyl-, tetrabutyl-, tetrahexyl-, and benzyltrimethylammonium hydroxides. The molar A/HEC ratio (molar ratio of alkali to HEC) used was 0.50, the diluent to HEC (D/HEC) weight ratio was 7.4, and the reaction diluent was aqueous /-butyl alcohol. Because some of the quaternary ammonium hydroxide charges would be accompanied by large additions of water, the initial water content of the diluent was adjusted so that the final diluent composition would be about 14.4% water in /-butyl alcohol. The results of these experiments are summarized in Table 2. 

---