Passivating potential alloys

FIG. 28-9 Typical electrochemical polarization curve for an active/passive alloy (with cathodic trace) showing active, passive, and transpassive regions and other important features. (NOTE Epp = primary passive potential, Ecaa- — freely corroding potential). 

Spontaneous Passivation The anodic nose of the first curve describes the primary passive potential Epp and critical anodic current density (the transition from active to passive corrosion), if the initial active/passive transition is 10 lA/cm or less, the alloy will spontaneously passivate in the presence of oxygen or any strong oxidizing agent. 

Table 10.32 Effect on critical current density and passivation potential on alloying nickel with chromium in In and IOn H2SO4 both containing 0-5N K2SO4 (after Myers, Beck and Fontana")...

Alloy Acid concentration Temp. ( C) Critical current density ( crit.. Am-2) Current density to maintain passivity (ip a.< Corrosion rate (mm y ) Unprotected protected Passive potential range (V)... 

Electroplating passive alloys Another application of strike baths reverses the case illustrated in the previous example. The strike is used to promote a small amount of cathode corrosion. When the passivation potential of a substrate lies below the cathode potential of a plating bath, deposition occurs onto the passive oxide film, and the coating is non-adherent. Stainless steel plated with nickel in normal baths retains its passive film and the coating is easily peeled off. A special strike bath is used with a low concentration of nickel and a high current density, so that diffusion polarisation (transport overpotential) depresses the potential into the active region. The bath has a much lower pH than normal. The low pH raises the substrate passivation potential E pa, which theoretically follows a relation... 

The production of corrosion-resistant materials hy alloying is well established, hut the mechanisms are noi lull) understood. It is known, of course, that elements like chromium, mckcl. titanium, and aluminum depend for their corrosion resistance upon a tenacious surface oxide layer (passive film). Alloying elements added for the purpose of passivation must be in solid solution. The potential of ion implantation is promising because restrictions deriving from equilibrium phase diagrams frequently do not applv li e., concentrations of elements beyond tile limits of equilibrium solid solubility might he incorporated). This can lead to heretofore unknown alloyed surfact-s which are very corrosion resistant... 

Polarization curves for iron, chromium, and alloys with 1, 6, 10, and 14 weight percent (wt%) chromium in iron are shown in Fig. 5.24 the environment is 1 N H2SO4 at 25 °C (Ref 21). Iron and chromium are body-centered-cubic metals, and the alloys are solid solutions having this structure. The passivation potential (Epp), the active peak current density (icrit), and the passive state current density (ip) are decreased... 

The extents of the passive potential regions have been reduced for all materials except pure chromium, and the curves for 90 and 100 wt% nickel indicate that an active-to-passive state transition no longer occurs. The magnitude of the influence of the chloride ions is emphasized by comparing the current densities for each alloy at 200 mV (SHE) with and without chloride ions present. 

Pitting corrosion is usually associated with active-passive-type alloys and occurs under conditions specific to each alloy and environment. This mode of localized attack is of major commercial significance since it can severely limit performance in circumstances where, otherwise, the corrosion rates are extremely low. Susceptible alloys include the stainless steels and related alloys, a wide series of alloys extending from iron-base to nickel-base, aluminum, and aluminum-base alloys, titanium alloys, and others of commercial importance but more limited in use. In all of these alloys, the polarization curves in most media show a rather sharp transition from active dissolution to a state of passivity characterized by low current density and, hence, low corrosion rate. As emphasized in Chapter 5, environments that maintain the corrosion potential in the passive potential range generally exhibit extremely low... 

The major alloying element contributing to resistance to pitting corrosion in iron- and nickel-base alloys is chromium. The effect of chromium in reducing both the critical current density and the passivating potential of iron in 1 N H2S04 is shown by the polarization curves of... 

The concepts in Chapters 2 and 3 are used in Chapter 4 to discuss the corrosion of so-called active metals. Chapter 5 continues with application to active/passive type alloys. Initial emphasis in Chapter 4 is placed on how the coupling of cathodic and anodic reactions establishes a mixed electrode or surface of corrosion cells. Emphasis is placed on how the corrosion rate is established by the kinetic parameters associated with both the anodic and cathodic reactions and by the physical variables such as anode/cathode area ratios, surface films, and fluid velocity. Polarization curves are used extensively to show how these variables determine the corrosion current density and corrosion potential and, conversely, to show how electrochemical measurements can provide information on the nature of a given corroding system. Polarization curves are also used to illustrate how corrosion rates are influenced by inhibitors, galvanic coupling, and external currents. 

---