Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Operating accelerators

Turbulence and high fluid velocities resulting from normal pump operation accelerated metal loss by abrading the soft, graphitically corroded surface (erosion-corrosion). The relatively rapid failure of this impeller is due to the erosive effects of the high-velocity, turbulent water coupled with the aggressiveness of the water. Erosion was aided in this case by solids suspended in the water. [Pg.383]

Data on aerosol formation from irradiated automobile exhaust 5.193.23. 239 confirm the marked sensitivity to hydrocarbon type observed in individual hydrocarbon studies. Aerosol formation increases with the olefinic and aromatic fuel content. However, changes in mode of engine operation (acceleration, idle) and inorganic variables (sulfur dioxide, relative humidity) have a more pronounced effect on aerosol formation than change in fuel composition. ... [Pg.60]

At many facdities, the practice is to operate the incineration system continuously until it breaks down because of equipment failures. This type of operation accelerates both bad performance and equipment deterioration rates. Repairs done after such breakdowns are usually far more extensive and costly than those performed during routine, preventive maintenance procedures. Also, items which are typically capable of lasting many years can fail in a fraction of that time if interrelated components are permitted to fail completely. [Pg.493]

Vifith respect to the effect of warm working after solution treatment on the subsequent aged properties of Ti-13-11-3, there is little difference between warm working and cold working. Both operations accelerate aging response. [Pg.525]

As noted earlier, most electron diffraction studies are perfonned in a mode of operation of a transmission electron microscope. The electrons are emitted themiionically from a hot cathode and accelerated by the electric field of a conventional electron gun. Because of the very strong interactions between electrons and matter, significant diffracted intensities can also be observed from the molecules of a gas. Again, the source of electrons is a conventional electron gun. [Pg.1379]

Likewise, the influence of the ligand catalyst ratio has been investigated. Increase of this ratio up to 1.75 1 resulted in a slight improvement of the enantioselectivity of the copper(L-tryptophan)-catalysed Diels-Alder reaction. Interestingly, reducing the ligand catalyst ratio from 1 1 to 0.5 1 resulted in a drop of the enantiomeric excess from 25 to 18 % instead of the expected 12.5 %. Hence, as anticipated, ligand accelerated catalysis is operative. [Pg.93]

A scintillator, sometimes known as the Daly detector, is an ion collector that is especially useful for studies on metastable ions. The principle of operation is illustrated in Figure 28.4. As with the first dynode of an electron multiplier, the arrival of a fast ion causes electrons to be emitted, and they are accelerated toward a second dynode. In this case, the dynode consists of a substance (a scintillator) that emits photons (light). The emitted light is detected by a commercial photon... [Pg.203]

An incident ion beam causes secondary electrons to be emitted which are accelerated onto a scintillator (compare this with the operation of a TV screen). The photons that are emitted (like the light from a TV screen) are detected not by eye but with a highly sensitive photon detector (photon multiplier), which converts the photon energy into an electric current. [Pg.203]

In both of these pieces of apparatus, isothermal operation and optimum membrane area are obtained. Good temperature control is essential not only to provide a value for T in the equations, but also because the capillary attached to a larger reservoir behaves like a thermometer, with the column height varying with temperature fluctuations. The contact area must be maximized to speed up an otherwise slow equilibration process. Various practical strategies for presetting the osmometer to an approximate n value have been developed, and these also accelerate the equilibration process. [Pg.550]

Venturi scmbbers can be operated at 2.5 kPa (19 mm Hg) to coUect many particles coarser than 1 p.m efficiently. Smaller particles often require a pressure drop of 7.5—10 kPa (56—75 mm Hg). When most of the particulates are smaller than 0.5 p.m and are hydrophobic, venturis have been operated at pressure drops from 25 to 32.5 kPa (187—244 mm Hg). Water injection rate is typicaUy 0.67—1.4 m of Hquid per 1000 m of gas, although rates as high as 2.7 are used. Increasing water rates improves coUection efficiency. Many venturis contain louvers to vary throat cross section and pressure drop with changes in system gas flow. Venturi scmbbers can be made in various shapes with reasonably similar characteristics. Any device that causes contact of Hquid and gas at high velocity and pressure drop across an accelerating orifice wiU act much like a venturi scmbber. A flooded-disk scmbber in which the annular orifice created by the disc is equivalent to a venturi throat has been described (296). An irrigated packed fiber bed with performance similar to a... [Pg.410]

Suspension polymerization of VDE in water are batch processes in autoclaves designed to limit scale formation (91). Most systems operate from 30 to 100°C and are initiated with monomer-soluble organic free-radical initiators such as diisopropyl peroxydicarbonate (92—96), tert-huty peroxypivalate (97), or / fZ-amyl peroxypivalate (98). Usually water-soluble polymers, eg, cellulose derivatives or poly(vinyl alcohol), are used as suspending agents to reduce coalescence of polymer particles. Organic solvents that may act as a reaction accelerator or chain-transfer agent are often employed. The reactor product is a slurry of suspended polymer particles, usually spheres of 30—100 pm in diameter they are separated from the water phase thoroughly washed and dried. Size and internal stmcture of beads, ie, porosity, and dispersant residues affect how the resin performs in appHcations. [Pg.386]


See other pages where Operating accelerators is mentioned: [Pg.129]    [Pg.142]    [Pg.26]    [Pg.39]    [Pg.24]    [Pg.109]    [Pg.761]    [Pg.414]    [Pg.129]    [Pg.142]    [Pg.26]    [Pg.39]    [Pg.24]    [Pg.109]    [Pg.761]    [Pg.414]    [Pg.53]    [Pg.809]    [Pg.1329]    [Pg.1329]    [Pg.1868]    [Pg.1917]    [Pg.2873]    [Pg.24]    [Pg.115]    [Pg.82]    [Pg.155]    [Pg.158]    [Pg.207]    [Pg.76]    [Pg.237]    [Pg.635]    [Pg.80]    [Pg.392]    [Pg.53]    [Pg.215]    [Pg.427]    [Pg.510]    [Pg.49]    [Pg.114]    [Pg.135]    [Pg.354]    [Pg.413]    [Pg.88]    [Pg.94]    [Pg.154]    [Pg.512]    [Pg.513]   
See also in sourсe #XX -- [ Pg.290 ]




SEARCH



Particle accelerators operation

Radioactive aerosols associated with the operation of high-energy accelerators

© 2024 chempedia.info