Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Nature of the Polymer

In an attempt to explain these observations several models, based upon kinetic or molecular considerations, have been reported. [Pg.190]


Styrene. Styrene is readily polymerised to a glass-clear resin, polystyrene, but the exact nature of the polymer is influenced by the nature of the catalyst, the temperature, solvent, etc. [Pg.1015]

In addition to the above, cyclic polymers, e.g. (RjSiOln, and also three-dimensional polymers can be formed. The exact nature of the polymer (its structure, and whether it is liquid or solid at room temperatures) will depend upon the substituted chloroalkyl-(or aryl-)silicane, or mixture of substituted silicanes, used and upon the experimental conditions. [Pg.1020]

The property to be predicted must be considered when choosing the method for simulating a polymer. Properties can be broadly assigned into one of two categories material properties, primarily a function of the nature of the polymer chain itself, or specimen properties, primarily due to the size, shape, and phase... [Pg.310]

This relationship with a = 1 was first proposed by Staudinger, but in this more general form it is known as the Mark-Houwink equation. The constants k and a are called the Mark-Houwink coefficients for a system. The numerical values of these constants depend on both the nature of the polymer and the nature of the solvent, as well as the temperature. Extensive tabulations of k and a are available Table 9.2 shows a few examples. Note that the units of k are the same as those of [r ], and hence literature values of k can show the same diversity of units as C2, the polymer concentration. [Pg.605]

Many ceUulosic derivatives form anisotropic, ie, Hquid crystalline, solutions, and cellulose acetate and triacetate are no exception. Various cellulose acetate anisotropic solutions have been made using a variety of solvents (56,57). The nature of the polymer—solvent interaction determines the concentration at which hquid crystalline behavior is initiated. The better the interaction, the lower the concentration needed to form the anisotropic, birefringent polymer solution. Strong organic acids, eg, trifluoroacetic acid are most effective and can produce an anisotropic phase with concentrations as low as 28% (58). Trifluoroacetic acid has been studied with cellulose triacetate alone or in combination with other solvents (59—64) concentrations of 30—42% (wt vol) triacetate were common. [Pg.297]

The processes used commercially for the manufacture of film and sheeting materials are generaUy similar in basic concept, but variations in equipment or process conditions are used to optimize output for each type of film or sheeting material. The nature of the polymer to be used, its formulation with plasticizers (qv), fillers (qv), flow modifiers, stabilizers, and other modifiers, as weU as its molecular weight and distribution are aU critical to the... [Pg.378]

Nitrile Rubber. Nitrile mbbers are made by the emulsion copolymerization of acrylonitrile (9—50%) and butadiene (6) and designated NBR. The ratio of acrylonitrile (ACN) to butadiene has a direct effect on the properties on the nature of the polymers. As the ACN content increases, the oil resistance of the polymer increases (7). As the butadiene content increases, the low temperature properties of the polymer are improved (see Elastomers, SYNTHETIC-NITRILE RUBBER). [Pg.232]

Benzene rings in both the skeleton structure and on the side groups can be subjected to substitution reactions. Such reactions do not normally cause great changes in the fundamental nature of the polymer, for example they seldom lead to chain scission or cross-linking. [Pg.95]

Stannett and Szwarc have argued that the permeability is a product of a factor F determined by the nature of the polymer, a factor G determined by the nature of gas and an interaction factor H (considered to be of little significance and assumed to be unity). [Pg.102]

The low unsaturation requires powerful curing systems whilst the hydrocarbon nature of the polymer causes bonding problems. To overcome these problems chlorinated and brominated butyl rubbers (CIIR and BUR) have been introduced and have found use in the tyre industry. [Pg.302]

Because of the chain-stiffening effect of the benzene ring the TgS of commercial materials are in the range 90-100°C and isotactic polymers have similar values (approx. 100°C). A consequence of this Tg value plus the amorphous nature of the polymer is that we have a material that is hard and transparent at room temperature. Isotactic polystyrenes have been known since 1955 but have not been of commercial importance. Syndiotactic polystyrene using metallocene catalysis has recently become of commercial interest. Both stereoregular polymers are crystalline with values of 230°C and 270°C for the isotactic and syndiotactic materials respectively. They are also somewhat brittle (see Section 16.3). [Pg.433]

The mechanical properties of polystyrene depend to some extent on the nature of the polymer (e.g. its molecular weight), on the method of preparing the sample for testing and on the method of test, as is the case with all plastics materials. [Pg.434]

As with the polysulphones, the deactivated aromatic nature of the polymer leads to a high degree of oxidative stability, with an indicated UL Temperature Index in excess of 250°C for PEEKK. The only other melt-processable polymers in the same league are poly(phenylene sulphides) and certain liquid crystal polyesters (see Chapter 25). [Pg.604]

Low air and gas permeability. The amorphous and highly saturated nature of the polymer chain prevents permeation of air and gases. [Pg.651]

Good flexibility and impact resistance. This is due to the amorphous nature of the polymers. [Pg.651]

Antioxidants. Antioxidants are rarely needed because of the highly saturated nature of the polymer chains. If protection against severe environmental ageing conditions is needed, typical antioxidants (Ethanox 702, Irganox 1010) can be added. In some cases, zinc dibutyldithiocarbamate (0.05-0.2 wt%) or butylated hydroxytoluene (BHT) can be used as stabilizers. [Pg.652]

The reversible aggregation of monomers into linear polymers exhibits critical phenomena which can be described by the 0 hmit of the -vector model of magnetism [13,14]. Unlike mean field models, the -vector model allows for fluctuations of the order parameter, the dimension n of which depends on the nature of the polymer system. (For linear chains 0, whereas for ring polymers = 1.) In order to study equilibrium polymers in solutions, one should model the system using the dilute 0 magnet model [14] however, a theoretical solution presently exists only within the mean field approximation (MFA), where it corresponds to the Flory theory of polymer solutions [16]. [Pg.510]

The hydrophilic surface characteristics and the chemical nature of the polymer backbone in Toyopearl HW resins are the same as for packings in TSK-GEL PW HPLC columns. Consequently, Toyopearl HW packings are ideal scaleup resins for analytical separation methods developed with TSK-GEL HPLC columns. Eigure 4.44 shows a protein mixture first analyzed on TSK-GEL G3000 SWxl and TSK-GEL G3000 PWxl columns, then purified with the same mobile-phase conditions in a preparative Toyopearl HW-55 column. The elution profile and resolution remained similar from the analytical separation on the TSK-GEL G3000 PWxl column to the process-scale Toyopearl column. Scaleup from TSK-GEL PW columns can be direct and more predictable with Toyopearl HW resins. [Pg.150]

It is difficult to decide what should serve as adequate column quality parameters for describing the performance of a set of GPC columns. The two most common measures are plate count and resolution. While both of these can be useful for monitoring the performance of a column set over time, it is not generally possible to a priori specify the performance needed for a specific analysis. This will depend on the nature of the polymer itself, as well as the other matrix components. [Pg.544]

The highest mechanical strengths are usually obtained when the fibre is used in fine fabric form but for many purposes the fibres may be used in mat form, particularly glass fibre. The chemical properties of the laminates are largely determined by the nature of the polymer but capillary attraction along the fibre-resin interface can occur when some of these interfaces are exposed at a laminate surface. In such circumstances the resistance of both reinforcement and matrix must be considered when assessing the suitability of a laminate for use in chemical plant. Glass fibres are most commonly used for chemical plant, in conjunction with phenolic resins, and the latter with furane, epoxide and, sometimes, polyester resins. [Pg.921]

Although the observations for PPV photodiodes of different groups are quite similar, there are still discussions on the nature of the polymer-metal contacts and especially on the formation of space charge layers on the Al interface. According to Nguyen et al. [70, 711 band bending in melal/PPV interfaces is either caused by surface states or by chemical reactions between the polymer and the metal and... [Pg.590]

Depending on the nature of the polymer-filler interaction and the fracture surface status (smooth or rough), Eq. (34) predicts either a rather smooth variation of the elongation with increasing filler concentration or a sharp drop at some small filler content. [Pg.31]

Upon cooling, molten and rubberlike polymers pass the glass transition and solidify as glassy materials. The temperature TB of the glass transition depends on the chemical nature of the polymer as well as on the number of crosslinks between the molecular chains. Two different test methods were used for the determination of the glass transition range ... [Pg.326]

With the increasing use of polymers in both the home and the workplace, there seems to have been a change in the nature of fires. Fire brigades now report fires that are shorter and more intense than previously there is also much more smoke and significantly greater amounts of toxic gases. All of these arise from the nature of the polymers being used in everyday life. [Pg.118]

Computerized Analytical Approach. The logic flow-chart for the analysis is shown in Figure 1. An assumption is first made about the nature of the polymer mixture. For example, in a two-component mixture different combinations of statistical... [Pg.175]


See other pages where Nature of the Polymer is mentioned: [Pg.60]    [Pg.203]    [Pg.404]    [Pg.307]    [Pg.138]    [Pg.488]    [Pg.139]    [Pg.498]    [Pg.627]    [Pg.790]    [Pg.133]    [Pg.329]    [Pg.682]    [Pg.163]    [Pg.509]    [Pg.157]    [Pg.76]    [Pg.82]    [Pg.219]    [Pg.199]    [Pg.105]    [Pg.115]    [Pg.155]    [Pg.2]    [Pg.551]   


SEARCH



A discussion concerning the nature of universal functions in polymer theory

Excitons The Nature of Excited States in Conjugated Polymers

Natural polymers

The History of Natural Polymers

The Nature of Charge Carriers in Conjugated Polymers

The Nature of Electronic Excitations in Matter (Polymer Blends)

The chemical nature of polymers

The coupled nature of internal rotations in polymers

© 2024 chempedia.info