Monomer addition, living polymerization

This finding is a significant improvement over aqueous ROMP systems using aqueous ROMP catalysts. The propagating species in these reactions is stable. The synthesis of water-soluble block copolymers can be achieved via sequential monomer addition. The polymerization is not of living type in the absence of acid. In addition to eliminating hydroxide ions, which would cause catalyst decomposition, the catalyst activity is also enhanced by the protonation of the phosphine ligands. Remarkably, the acids do not react with the ruthenium alkylidene bond. 

With water-soluble carbene complexes 17 and water-soluble monomers 18, living polymerization can be carried out in aqueous solution, without the addition of surfactants or organic cosolvents [116]. 

Due to the water insolubility of these metal carbenes, aqueous polymerizations represent heterogeneous multiphase mixtures. Investigation of ROMP of the hydrophilic monomer 8 or of a hydrophobic norbomene in aqueous emulsion (catalyst precursor 7 b added as methylene chloride solution) or suspension demonstrated that the polymerization can occur in a living fashion. For example, at a monomer to catalyst ratio 8/7b = 100 with 78% yield, poly-8 of Mw/Mn 1.07 vs. polystyrene standards was obtained [68]. Using water-soluble carbene complexes of type 9 and water-soluble monomers 10, living polymerization can be carried out in aqueous solution, without the addition of surfactants or organic co-solvents [69]. 

A brief review has appeared covering the use of metal-free initiators in living anionic polymerizations of acrylates and a comparison with Du Font s group-transfer polymerization method (149). Tetrabutylammonium thiolates mn room temperature polymerizations to quantitative conversions yielding polymers of narrow molecular weight distributions in dipolar aprotic solvents. Block copolymers are accessible through sequential monomer additions (149—151) and interfacial polymerizations (152,153). 

Anionic polymerization, if carried out properly, can be truly a living polymerization (160). Addition of a second monomer to polystyryl anion results in the formation of a block polymer with no detectable free PS. This technique is of considerable importance in the commercial preparation of styrene—butadiene block copolymers, which are used either alone or blended with PS as thermoplastics. 

The living polymerization process offers enormous flexibiUty in the design of polymers (40). It is possible to control terminal functional groups, pendant groups, monomer sequencing along the main chain (including the order of addition and blockiness), steric stmcture, and spatial shape. 

The formation of polymer can be considered as a quasi-living polymerization. After the polymerization is complete, it can be reinitiated with the addition of more monomer to the unquenched polymer. However, the degree of polymerization cannot be predicted by the monomer/initiator molar ratio, the polydispersity is 1.5-2.0, and water, or even carboxylic acids, act as inhibitors and do not terminate the polymerization [10]. 

Sequential addition of monomers 6 7-26-27-114) is the most obvious procedure. Once the first monomer has been polymerized, the resulting living species is used as a polymeric initiator for the polymerization of the second one. The monomers are to be added in the order of increasing electron affinity to provide efficient and fast initiation 26 U4). This condition is rather restrictive, and the number of monomer systems that can be used is limited (Table 5). Moreover, when the second monomer contains an electrophilic function (e.g. ester) which could lead to side reactions, it is necessary to first lower the nucleophilicity of the living site. This is best done by intermediate addition of 1.1-diphenylethylene25). The stabilized diphenylmethyl anions do not get involved in side reactions with ester functions, while initiation is still quantitative and fast. 

Though living anionic polymerization is the most widely used technique for synthesizing many commercially available TPEs based on styrenic block copolymers, living carbocationic polymerization has also been developed in recent years for such purposes [10,11], Polyisobutylene (PlB)-based TPEs, one of the most recently developed classes, are synthesized by living carbocationic polymerization with sequential monomer addition and consists of two basic steps [10] as follows ... 

Living" carbocationic polymerizations are most difficult to achieve mainly because of chain transfer to monomer and termination processes both of which frequently occur in carbocationic polymerizations. It has recently been demonstrated (JL) that "quasiliving" polymerization of a-methylstyrene (aMeSt) can be achieved by slow and continuous monomer addition and that the number-average molecular weight (Mn) of PaMeSt increases linearly with the weight of added monomer. A theory for quasiliving polymerizations has been developed (2). 

A series of bis(phenoxide) aluminum alkoxides have also been reported as lactone ROP initiators. Complexes (264)-(266) all initiate the well-controlled ROP of CL, NVL.806,807 and L-LA.808 Block copolymers have been prepared by sequential monomer addition, and resumption experiments (addition of a second aliquot of monomer to a living chain) support a living mechanism. The polymerizations are characterized by narrow polydispersities (1.20) and molecular weights close to calculated values. However, other researchers using closely related (267) have reported Mw/Mn values of 1.50 and proposed that an equilibrium between dimeric and monomeric initiator molecules was responsible for an efficiency of 0.36.809 In addition, the polymerization of LA using (268) only achieved a conversion of 15% after 5 days at 80 °C (Mn = 21,070, Mn calc 2,010, Mw/Mn = 1.46).810... 

---