Molecular-Weight Compounds

Most properties of linear polymers are controlled by two different factors. The chemical constitution of tire monomers detennines tire interaction strengtli between tire chains, tire interactions of tire polymer witli host molecules or witli interfaces. The monomer stmcture also detennines tire possible local confonnations of tire polymer chain. This relationship between the molecular stmcture and any interaction witli surrounding molecules is similar to tliat found for low-molecular-weight compounds. The second important parameter tliat controls polymer properties is tire molecular weight. Contrary to tire situation for low-molecular-weight compounds, it plays a fimdamental role in polymer behaviour. It detennines tire slow-mode dynamics and tire viscosity of polymers in solutions and in tire melt. These properties are of utmost importance in polymer rheology and condition tlieir processability. The mechanical properties, solubility and miscibility of different polymers also depend on tlieir molecular weights. 

Small molecules can penetrate and penneate tlirough polymers. Because of this property, polymers have found widespread use in separation teclmology, protection coating, and controlled delivery [53]. The key issue in these applications is the selective penneability of the polymer, which is detennined by the diffusivity and the solubility of a given set of low-molecular-weight compounds. The diffusion of a small penetrant occurs as a series of jumps... 

Figure C2.1.18. Schematic representation of tire time dependence of tire concentration profile of a low-molecular-weight compound sorbed into a polymer for case I and case II diffusion. In botli diagrams, tire concentration profiles are calculated using a constant time increment starting from zero. The solvent concentration at tire surface of tire polymer, x = 0, is constant.

For mixture.s the picture is different. Unless the mixture is to be examined by MS/MS methods, usually it will be necessary to separate it into its individual components. This separation is most often done by gas or liquid chromatography. In the latter, small quantities of emerging mixture components dissolved in elution solvent would be laborious to deal with if each component had to be first isolated by evaporation of solvent before its introduction into the mass spectrometer. In such circumstances, the direct introduction, removal of solvent, and ionization provided by electrospray is a boon and puts LC/MS on a level with GC/MS for mixture analysis. Further, GC is normally concerned with volatile, relatively low-molecular-weight compounds and is of little or no use for the many polar, water soluble, high-molecular-mass substances such as the peptides, proteins, carbohydrates, nucleotides, and similar substances found in biological systems. LC/MS with an electrospray interface is frequently used in biochemical research and medical analysis. 

Attempts to characterize polymeric substances had been made, of course, and high molecular weights were indicated, even if they were not too accurate. Early workers tended to be more suspicious of the interpretation of the colliga-tive properties of polymeric solutions than to accept the possibility of high molecular weight compounds. Faraday had already arrived at Cs Hg as the empirical formula of rubber in 1826, and isoprene was identified as the product... 

The terminal groups of a polymer chain are different in some way from the repeat units that characterize the rest of the molecule. If some technique of analytical chemistry can be applied to determine the number of these end groups in a polymer sample, then the average molecular weight of the polymer is readily evaluated. In essence, the concept is no different than the equivalent procedure applied to low molecular weight compounds. The latter is often included as an experiment in general chemistry laboratory classes. The following steps outline the experimental and computational essence of this procedure ... 

Before concluding this section, there is one additional thermodynamic factor to be mentioned which also has the effect of lowering. Since we shall not describe the thermodynamics of polymer solutions until Chap. 8, a quantitative treatment is inappropriate at this point. However, some relationships familiar from the behavior of low molecular weight compounds may be borrowed for qualitative discussion. The specific effect we consider is that of chain ends. The position we take is that they are foreign species from the viewpoint of crystallization. 

Single crystals such as those shown in Fig. 4.11 are not observed in crystallization from the bulk. Crystallization from dilute solutions is required to produce single crystals with this kind of macroscopic perfection. Polymers are not intrinsically different from low molecular weight compounds in this regard. 

The following expression, known as the Dolittle equation, has been found to accurately describe the viscosity of low molecular weight compounds ... 

Next let us consider the light scattered by liquids of low molecular weight compounds. We are actually not directly interested in this quantity per se, but in scattering by solutions-polymer solutions eventually, but for now solutions of small solute molecules. The solvent in such a solution does scatter, but, in practice, the intensity of light scattered by pure solvent is measured and subtracted as a blank correction from the scattering by the solution. 

Phytoalexins are low molecular weight compounds produced in plants as a defense mechanism against microorganisms. They do, however, exhibit toxicity to humans and other animals in addition to microbes (30). Coumarins, glycoalkaloids, isocoumarins, isoflavonoids, linear furanocoumarins, stilbenes, and terpenes aU. fall into the category of phytoalexins (31). Because phytoalexins are natural components of plants, and because their concentration may increase as a response to production and management stimuli, it is useful to recogni2e the possible effects of phytoalexins in the human diet. 

As a low molecular weight compound DAS is not significantly immunogenic, ie, it is a hapten and thus requires conjugation to a suitable antigenic carrier in order to eUcit a successfiil antibody response in animals. DAS treated with succinic anhydride results in the D AS—hemisuccinate (DAS—HMS) shown. 

Oxidation of LLDPE starts at temperatures above 150°C. This reaction produces hydroxyl and carboxyl groups in polymer molecules as well as low molecular weight compounds such as water, aldehydes, ketones, and alcohols. Oxidation reactions can occur during LLDPE pelletization and processing to protect molten resins from oxygen attack during these operations, antioxidants (radical inhibitors) must be used. These antioxidants (qv) are added to LLDPE resins in concentrations of 0.1—0.5 wt %, and maybe naphthyl amines or phenylenediamines, substituted phenols, quinones, and alkyl phosphites (4), although inhibitors based on hindered phenols are preferred. 

Cyclic Peroxides. CycHc diperoxides (4) and triperoxides (5) are soHds and the low molecular weight compounds are shock-sensitive and explosive (151). The melting points of some characteristic compounds of this type are given in Table 5. They can be reduced to carbonyl compounds and alcohols with zinc and alkaH, zinc and acetic acid, aluminum amalgam, Grignard reagents, and warm acidified iodides (44,122). They are more difficult to analyze by titration with acidified iodides than the acycHc peroxides and have been sucessfuUy analyzed by gas chromatography (112). 

Both the m- and -phenylenediamines are used to manufacture sulfur dyes, either by refluxing in aqueous sodium polysulfide, or heating with elementary sulfur at 330°C to give the leuco form of the dye. These dyes are polymeric, high molecular weight compounds, and soluble in base. The color is developed by oxidation on the fabric. 2,4-Toluenediamine and sulfur give Sulfur Orange 1 (14). 

Separate all noncondensables before feeding to WEE or SPE unit (even a small amount of noncondensables overloads vacuum system, especially at ultrahigh vacuum ranges) most low molecular weight compounds do not condense at cooling water temperatures under high vacuum. 

---