Metal particle nanocomposites

There is a strong necessity to define formulations components processes conditions for nanostructured materials filled by metallic additives. Another task is optimization of components, nanocomposites and diluents combination and, in what follows, curing processes with determined temperature mode. The result of these arrangements will be materials with layerwise homogeneous metal particles/nanocomposites distribution formulation in ligand shell. 

The result of these arrangements will be homogeneous metal particles/ nanocomposites distribution in acetylacetone ligand shell. In the capacity of conductive filler silver nanoclusters/nanocrystals and copper-nickel/ carbon nanocomposites can be used. It should be lead to decrease volume resistance from 10" to 10" Q-cm and increase of adhesive/paste adhesion. 

However, for the dendrimer nanocomposite metallic systems this change in shape was not observed. Again, due to the high stability to intense laser pulses, the anisotropy value of the gold dendrimer nanocomposite, which can be viewed as a measure of the symmetry of the particle, did not change after several repeated cycles of measurements. It is possible that the initial optical pumping of the electron-phonon modes of the metal particles is partially absorbed by the encapsulating PAMAM dendrimer. 

The emission of the metal particles may thus originate from a band-to-band transition in the metal particle, which occurs at about 516 nm for gold [60, 119]. As stated above, the nature of the interaction of the dendrimer (PAMAM) host is still uncertain, there could be very strong electrostatic interactions that may play a part in the enhancement of the metal particles quantum efficiency for emission. However, one would expect that this enhancement would result in slightly distorted emission spectra, different from what was observed for the gold dendrimer nanocomposite. Further work is necessary to completely characterize the manner in which the dendrimer encapsulation enhances the emission of the metal nanoparticles. With further synthetic work in preparation of different size nanoparticles (in other words elongated and nonspherical shape particles, including nanorods) it may be possible to develop the accurate description of a... 

V. Subraniam, E. Wolf, P.V. Kamat, Catalysis with Ti02/gold nanocomposites. Effect of metal particle size on the Fermi level equilibration, J. Am. Chem. Soc. 126 (2004) 4943-4950. 

HREM methods are powerful in the study of nanometre-sized metal particles dispersed on ceramic oxides or any other suitable substrate. In many catalytic processes employing supported metallic catalysts, it has been established that the catalytic properties of some structure-sensitive catalysts are enhanced with a decrease in particle size. For example, the rate of CO decomposition on Pd/mica is shown to increase five-fold when the Pd particle sizes are reduced from 5 to 2 nm. A similar size dependence has been observed for Ni/mica. It is, therefore, necessary to observe the particles at very high resolution, coupled with a small-probe high-precision micro- or nanocomposition analysis and micro- or nanodiffraction where possible. Advanced FE-(S)TEM instruments are particularly effective for composition analysis and diffraction on the nanoscale. ED patterns from particles of diameter of 1 nm or less are now possible. 

Bright field TEM micrograph showing the metal particle morphology in a Cu-Al203 glass-doped nanocomposite. 

For most metal-reinforced nanocomposites the thermal expansion coefficient of the metal phase will be larger than that of the matrix, reversing the expected stress fields compared to SiC-reinforced alumina. Thus while the tensile radial stresses surrounding occluded particles may induce transgranular cracking, the compressive hoop stresses may inhibit crack propagation if the particles are located at grain boundaries. Macrostresses in sub-micron Ni... 

The initial interest in ceramic matrix nanocomposites arose from reports by Niihara and co-workers indicating enhanced mechanical properties due to the presence of ceramic (SiC) particles.53 With the development of various processing routes to introduce nanometer-sized metal particles in a ceramic matrix, variations in functional (i.e. magnetic) properties are possible. In the following we briefly review the microstructurally dependent properties, with emphasis on the possible mechanisms leading to improved properties and using SiC-reinforced alumina as a point of comparison. 

In metal-reinforced ceramic matrix nanocomposites, matrix grain refinement has also been demonstrated by Niihara and co-workers.12 At the same time, as mentioned in the previous section, significant residual stress fields have been measured for Ni-reinforced alumina nanocomposites,23 although with reversed compression-tension fields compared to SiC-reinforced alumina. Thus for metal particles below the critical size for intrinsic cracking11 and... 

Specific catalytic properties of synthesized Pd-PPX nanocomposites have been explained by the tunnel charge transfer between nanoparticles. As mentioned in Section 2, the energy of Fermi level of small metal particle depends on its size [14], At the same time, M nanoparticles immobilized in PPX matrix have rather wide size distribution in the range 2-8 nm (Section 3). Electron transfer between particles of different size results in their mutual charging that leads to equalization of their electrochemical potentials [15],... 

Abstract. IR pyrolysis of PAN and PAN based composites yields ordered graphitelike structure as well as several carbon nanostructures. Metal-carbon nanocomposites, in which the nanosized metal particles were introduced into the structure of carbon matrix in the course of IR pyrolysis of composite-precursor on the basis of PAN and metal (Gd, Pt, Ru, Re) compounds were prepared. The carbon phase of metal-carbon nanocomposites was shown to include different types of nano structured carbon particles. Bamboo-like CNT were observed in the structure of pyrolized at 910 and 1000°C composite-precursor based on PAN and GdCl3. At T=1200°C the solid carbon spheres with diameter in the range of 50-360 nm and octahedral carbon particles with the size in the range of 300-350 nm were observed. These nanostructured particles consist of carbon only or they include Gd nanoparticles incapsulated in carbon shell. IR pyrolysis of composite-precursor based on PAN as well as H2PtCl6 and RuC13 or NH4Re04 (Pt Ru(Re)=10 l) allows the preparation of Pt-Ru and Pt-Re alloys nanoparticles with 2[Pg.577]

Including into initial PAN solution metal compounds provides the formation of metal-carbon nanocomposites. The nanosized metal particles were introduced into the structured carbon matrix in the course of IR pyrolysis of composite-precursor on the basis of PAN and compounds of corresponding metals. In this way carbon composites containing nanosized Gd particles (4Efficient reduction of metal takes place in the course of IR pyrolysis of composite-precursor with participation of hydrogen, which is released in dehydrogenation of main polymeric chain of PAN. 

The carbon phase of obtained metal-carbon nanocomposites was shown to contain different types of nanostructured carbon particles in parallel with main graphite-like structures. Bamboo-like carbon nanotubes (CNT) with 14-30 nm in their outer diameter were observed in structured carbon material when GdCl3 was used as a component of composite-precursor (Fig. 4). In this case IR radiation intensity provides the heating of sample to 910 and 1000°C. 

Metal-carbon nanocomposites containing bimetallic nanosized Pt-Ru (Pt-Re) particles were prepared in the course of IR-pyrolysis composite-precursor containing PAN as well as H2PtCl6 and RuCL, (or NFEReCA) in the ratio Pt Ru (Re) = 10 1. 

---