Mechanism transmission electron microscopy

Keywords homopolymer, block copolymer, hinge, living hinge, plastic hinge, hinge geometry, process parameter, morphology, oriented layers, stacked lamellae, molecular orientation, hard elasticity, deformation mechanism, transmission electron microscopy (TEM). 

The mechanism for coercivity in the Cr—Co—Fe alloys appears to be pinning of domain walls. The magnetic domains extend through particles of both phases. The evidence from transmission electron microscopy studies and measurement of JT, and anisotropy vs T is that the walls are trapped locally by fluctuations in saturation magnetization. 

Paine et al. [99] tried different stabilizers [i.e., hydroxy propylcellulose, poly(N-vinylpyrollidone), and poly(acrylic acid)] in the dispersion polymerization of styrene initiated with AIBN in the ethanol medium. The direct observation of the stained thin sections of the particles by transmission electron microscopy showed the existence of stabilizer layer in 10-20 nm thickness on the surface of the polystyrene particles. When the polystyrene latexes were dissolved in dioxane and precipitated with methanol, new latex particles with a similar surface stabilizer morphology were obtained. These results supported the grafting mechanism of stabilization during dispersion polymerization of styrene in polar solvents. 

Usually, the molecular strands are coiled in the glassy polymer. They become stretched when a crack arrives and starts to build up the deformation zone. Presumably, strain softened polymer molecules from the bulk material are drawn into the deformation zone. This microscopic surface drawing mechanism may be considered to be analogous to that observed in lateral craze growth or in necking of thermoplastics. Chan, Donald and Kramer [87] observed by transmission electron microscopy how polymer chains were drawn into the fibrils at the craze-matrix-interface in PS films [92]. One explanation, the hypothesis of devitrification by Gent and Thomas [89] was set forth as early as 1972. 

The isotropic form has little graphitic characteristic and essentially no optical activity. It is composed of very fine grains without observable orientation and for this reason, it is known as isotropic carbon rather than isotropic graphite. It is often obtained in fluidized-bed deposition, possibly due to continuous surface regeneration by the mechanical rubbing action of the bed. An isotropic structure, observed by transmission electron microscopy, is shown in Fig. 7.4.111]... 

In the matrix of PLA/ polycaprilactone (PCL)/OMMT nano-composites, the silicate layers of the organoclay were intercalated and randomly distributed (Zhenyang et at, 2007). The PLA/PCL blend significantly improved the tensile and other mechanical properties by addition of OMMT. Thermal stability of PLA/PCL blends was also explicitly improved when the OMMT content is less than 5%wt. Preparation of PLA/thermoplastic starch/MMT nano-composites have been investigated and the products have been characterized using X-Ray diffraction, transmission electron microscopy and tensile measurements. The results show improvement in the tensile and modulus, and reduction in fracture toughness (Arroyo et ah, 2010). 

SEM), and transmission electron microscopy (TEM). Study of mechanical and thermal properties shows significant improvement over the gum. The thermal results are given in Table 2.1. 

The authors have characterized the graft polymer by solvent extraction, transmission electron microscopy, dynamic mechanical analysis, mechanical testing (including measurement of tensile, tear, and impact strength), and morphology by SEM. The reaction scheme is given in Figure 11.25. 

Recent demands for polymeric materials request them to be multifunctional and high performance. Therefore, the research and development of composite materials have become more important because single-polymeric materials can never satisfy such requests. Especially, nanocomposite materials where nanoscale fillers are incorporated with polymeric materials draw much more attention, which accelerates the development of evaluation techniques that have nanometer-scale resolution." To date, transmission electron microscopy (TEM) has been widely used for this purpose, while the technique never catches mechanical information of such materials in general. The realization of much-higher-performance materials requires the evaluation technique that enables us to investigate morphological and mechanical properties at the same time. AFM must be an appropriate candidate because it has almost comparable resolution with TEM. Furthermore, mechanical properties can be readily obtained by AFM due to the fact that the sharp probe tip attached to soft cantilever directly touches the surface of materials in question. Therefore, many of polymer researchers have started to use this novel technique." In this section, we introduce the results using the method described in Section 21.3.3 on CB-reinforced NR. 

The contribution by Rouzaud et al. teaches to apply a modified version of high resolution Transmission Electron Microscopy (TEM) as an efficient technique of quantitative investigation of the mechanism of irreversible capacity loss in various carbon candidates for application in lithium-ion batteries. The authors introduce the Corridor model , which is interesting and is likely to stimulate active discussion within the lithium-ion battery community. Besides carbon fibers coated with polycarbon (a candidate anode material for lithium-ion technology), authors study carbon aerogels, a known material for supercapacitor application. Besides the capability to form an efficient double electric layer in these aerogels, authors... 

Recently, Kroeze et al. prepared polymeric iniferter 34 including poly(BD) segments in the main chain [152]. They successfully synthesized poly(BD)-block-poly(SAN), which was characterized by gel permeation chromatography, elemental analysis, thermogravimetric analysis, NMR, dynamic mechanical thermal analysis, and transmission electron microscopy. By varying the polymerization time and iniferter concentration, the composition and the sequence length were controlled. The analysis confirmed the chain microphase separation in the multiblock copolymers. 

---