Load-carrying capacity

Apart from its low-friction properties, the other attribute of molybdenum disulphide which is important in lubrication is its very high load-carrying capacity. Having said that, it is then impossible to give a specific value for the load-carrying capacity, because it depends entirely on the form and conditions in which it is used. 

It is now generally accepted that the very low sliding friction of molybdenum disulphide is due to the very low shear strength parallel to the basal plane of the crystal lamellae, compared with the high strength or hardness perpendicular to the basal plane. The low shear strength is caused by the wide separation distance 

The actual coefficient of friction of a molybdenum disulphide film will depend on the integrity of the film, contact pressure, temperature, humidity, film thickness and presence of contaminants. For a pure, smooth, dense, properly-oriented film at high contact pressure in a clean, dry atmosphere in unidirectional sliding, coefficients of friction as low as 0.02 have been reported. With impurities, poor orientation, humidity and low pressure, the coefficient of friction may be as high as 0.3. 

---

Pipe attachment devices are either integral or nonintegral with the shell of the pipe. The particular type is selected according to load-carrying capacity, severity of service, and the desirability of welding directly to the pipe. 

Lugs are an improvement of the ear type by the addition of an element to provide lateral stiffening which also serves to improve load-carrying capacity and lateral strength. In high temperature services, unless heavily insulated, lugs are susceptible to distortion. 

Cylindrical tmnnions are of more favorable contour for stress distribution and frequently are used in high temperature services. Their load-carrying capacity is high and their stmctural effect on the pipe shell can easily be deterrnined. 

Three-lohe heating. The three-lobe bearing is not commonly used in turbomachines. It has a moderate load-carrying capacity and can be operated in both directions. 

Offset halve.s. In principle, this bearing acts very similar to a pressure dam bearing. Its load-carrying capacity is good. It is restricted to one direction of rotation. 

Load-carrying capacity and life expectancy of bearings 8/214... 

In LT systems reactive control is provided to improve the load p.f. and hence its load-carrying capacity, as discussed in Chapter 23. This is achieved by offsetting the inductive content of the load ctirrcnt at the receiving or the consumer end by the use of shunt capacitors and hence support the system by reducing line losses and improving its active load current (/ cos 0) carrying capacity. 

The evaluation of the load-carrying capacity of a specific laminate (including the load-deformation behavior) is a straightforward deterministic process and is described in Section 4.5. For example, a 20-layered laminate has a certain load-carrying capacity tor one type of loading (and a different capacity tor a different type of loading). 

Helical, external Connects parallel and non-parallel shafts superior to spur gears in load-carrying capacity, quietness, and smoothness high efficiency Higher friction than spur gears, high end thrust... 

At high speeds, however, a position can be reached in which the load-carrying capacity increases with speed. The explanation is thought to be that when the teeth are in contact for such a short time, the oil film is not squeezed out and a separating film is therefore maintained. 

In plain bearings, the lubricating fluid must be replenished to compensate for end leakage in order to maintain their load-carrying capacity. Pressure lubrication from a pump-or gravity-fed tank, or automatic lubricating devices such... 

Figure 60.27 shows the ball installation procedure for roller bearings. The designed load carrying capacity of Conrad-type bearings is determined by the number of balls that can be installed between the rings. Ball installation is accomplished by the following procedure ... 

On the other hand, thermal stress concentrations occur at these layers, since the thermal properties of either phase are different. Therefore, the load-carrying capacity of the system is affected by these thermal stresses, according to the nature of the stress field, developed by the external loads. 

For a slender rod with Lja = 100, we get R = 13,000. Note that the ratio is independent of E, although the load carrying capacity may vary with E and the actual magnitude of deflections will depend on E. 

Although one can design flexures with quite extreme ratios of stiffness, often the design is also hmited by various space constraints, limits to allowed deflections, required load carrying capacity, and the need to avoid buckling. 

Even though the load carrying capacity and friction behavior are apparently of interest to the authors, they are not presented here because no general law can be constructed if there are no practically reliable parameters presented. This remains to be done in our further research. 

The integration of the gas pressure gives the load carrying capacity, F, of a bearing,... 

Table 5 gives the comparisons of the calculated load carrying capacity F, the pitch moment M (moment around Y axis), the maximum and minimum dimensionless pressures Pmax. Pmin the Speed of 9.57557 m/s, with and without consideration of the rarefaction effect. All of the absolute values of F, M, min become lower when the rar-... 

Let us compare the magnitude of the van der Waals pressure with that of air bearing pressure. In Section 3.2, we have shown the numerical solution of gas pressure distribution for a two-rail slider and a O t pe slider. By simply summing up the contributions of gas pressure and van der Waals pressure and integrating over the whole slider surface area, the total dimensionless load carrying capacity becomes... 

---