Linear polymers density

One of the mam uses of the linear a olefins prepared by oligomerization of ethylene is in the preparation of linear low density polyethylene Linear low density polyethylene is a copoly mer produced when ethylene is polymerized in the presence of a linear a olefin such as 1 decene [H2C=CH(CH2)7CH3] 1 Decene replaces ethylene at random points in the growing polymer chain Can you deduce how the structure of linear low density polyethylene differs from a linear chain of CH2 units ... 

Depending on their stmctural type, PEPE oils are stable up to 300—400°C ia air. Pure oxygen ia a test bomb at 13 MPa (1886 psi) at temperatures up to 400°C was tolerated with no ignition (43). Densities at 20°C vary from 1.82 to 1.89 g/mL, and viscosities from 10 to 1600 mm /s. The pour poiat for low temperature operation usually ranges from —30 to —70° C, and the viscosity iadex varies from about 50 for low viscosity grades up to 150 for more viscous oils and considerably higher for fully linear polymers (43). 

The majority of spunbonded fabrics are based on isotactic polypropylene and polyester (Table 1). Small quantities are made from nylon-6,6 and a growing percentage from high density polyethylene. Table 3 illustrates the basic characteristics of fibers made from different base polymers. Although some interest has been seen in the use of linear low density polyethylene (LLDPE) as a base polymer, largely because of potential increases in the softness of the final fabric (9), economic factors continue to favor polypropylene (see OlefinPOLYMERS, POLYPROPYLENE). 

Low Pressure Linear (Low Density) Polyethylene" in ECT3rd ed., under "Olefin Polymers," Vol. 16, pp. 385—401, byj. N. Short, Phillips Petroleum Co. 

Polystyrene. Polystyrene [9003-53-6] is a thermoplastic prepared by the polymerization of styrene, primarily the suspension or bulk processes. Polystyrene is a linear polymer that is atactic, amorphous, inert to acids and alkahes, but attacked by aromatic solvents and chlorinated hydrocarbons such as dry cleaning fluids. It is clear but yellows and crazes on outdoor exposure when attacked by uv light. It is britde and does not accept plasticizers, though mbber can be compounded with it to raise the impact strength, ie, high impact polystyrene (HIPS). Its principal use in building products is as a foamed plastic (see Eoamed plastics). The foams are used for interior trim, door and window frames, cabinetry, and, in the low density expanded form, for insulation (see Styrene plastics). 

In the Institut Fransais du Petrc le process (62), ethylene is dimerized into polymer-grade 1-butene (99.5% purity) suitable for the manufacture of linear low density polyethylene. It uses a homogeneous catalyst system that eliminates some of the drawbacks of heterogeneous catalysts. It also inhibits the isomerization of 1-butene to 2-butene, thus eliminating the need for superfractionation of the product (63,64). The process also uses low operating temperatures, 50—60°C, and pressures (65). 

Union Carbide Corp. also uses a siUca-supported chromium catalyst in their extremely low cost Unipol gas-phase linear low density ethylene copolymer process, which revolutionized the industry when it was introduced in 1977 (86—88). The productivity of this catalyst is 10 —10 kg polymer/kg transition metal contained in the catalyst. By 1990, the capacity of Unipol linear low density polyethylene reactors was sufficient to supply 25% of the world s total demand for polyethylene. 

CSM products may be divided into three groups depending on the type of precursor resin low density (LDPE), high density (HDPE), and linear low density (LLDPE). LDPE is made by a high pressure free-radical process, while HDPE and LLDPE are made via low pressure, metal coordination catalyst processes (12) (see Olefin polymers). 

The more recently developed so-called linear low-density polyethylenes are virtually free of long chain branches but do contain short side chains as a result of copolymerising ethylene with a smaller amount of a higher alkene such as oct-1-ene. Such branching interferes with the ability of the polymer to crystallise as with the older low-density polymers and like them have low densities. The word linear in this case is used to imply the absence of long chain branches. 

The linear low-density polyethylenes discussed in the previous chapter might be considered as variations of this type of polymer. 

Linear low-density polyethylene (LLDPE) is produced in the gas phase under low pressure. Catalysts used are either Ziegler type or new generation metallocenes. The Union Carbide process used to produce HDPE could be used to produce the two polymer grades. Terminal olefins (C4-C6) are the usual comonomers to effect branching. 

Due to the presence of residual double bonds, the polymer could be cross inked with regular agents. TPR is a linear polymer with a high trans configuration. It is highly amorphous at normal temperatures and has a Tg of about 90°C and a density of 0.85. 

The presence of a large number of chain-ends in the fully synthesized dendrimer molecules makes them highly soluble and also readily miscible, for example with other dendrimer solutions. The solubility is controlled by the nature of the end-groups, so that dendrimers with hydrophilic groups, such as hydroxyl or carboxylic acid, at the ends of the branches are soluble in polar solvents, whereas dendrimers with hydrophobic end-groups are soluble in non-polar solvents. The density of the end-groups at the surface of the dendrimer molecule means that they have proportionately more influence on the solubility than in linear polymers. Hence a dendritic polyester has been shown to be more soluble in tetrahydrofuran than an equivalent linear polyester. 

Both thermosets and thermoplastics are used as food-contact materials, though thermoplastics predominate in this appfication. Examples of the former are phenol- and urea-formaldehyde, while probably the best known example of the latter is low-density poly(ethylene). Other linear polymers are used include high-density poly(ethylene), poly(propylene), and PVC, all of which find quite extensive use. Polymers for food packaging may be in the form of films and other flexible items, or in the form of rigid containers, such as clear drinks bottles or opaque cartons for dairy products. 

---