Zinc/cadmium lamps

Thin-layer plates were made with silica gel-calcium sulfate and each contained a mixture of zinc silicate and zinc cadmium sulfide as phosphors. Separated components are generally visible under ultraviolet light by fluorescence quenching. This was true, in part, for the pyrethrins, except that some of the separated components possessed a natural fluorescence under the ultraviolet lamps. 

Mercury Vapor Lamp Zinc Vapor Lamp Cadmium Vapor Lamp... 

Gas discharge lamps containing deuterium, mercury, zinc, cadmium, or xenon are the most common sources. They exhibit high spectral radiance and good stability. 

Vapor discharge lamps produce emission by passing an electric current through a vapor composed at least partly of the element of interest. Such lamps are produced by Osram in Germany and Philips in Holland. Osram lamps exist for the elements mercury, thallium, zinc, cadmium, and the alkalis. 

Aluminium is widely applied for decorative and protective requirements, while cadmium , zinc and titanium have been applied to ferrous materials chiefly for their protective value. The method finds particular application in the plating of high-tensile steels used in aviation and rocketry, car fittings and lamp reflectors, and gramophone record master discs, as well as in the preparation of specimens for electron microscopy and in rendering insulated surfaces electrically conducting, e.g. metallising of capacitors and resistors. 

The photodimerization of simple isolated olefinic bonds is rarely observed because of the absorption of these compounds in the high-energy or vacuum-ultraviolet region. One case reported is that of the photo-dimerization of 2-butene.<2) Irradiation of liquid cw-2-butene with light from a cadmium (A = 229, 227, 214 nm) or zinc (A = 214 nm) lamp was reported to lead to dimers (1) and (2) ... 

Armannsson [659] has described a procedure involving dithizone extraction and flame atomic absorption spectrometry for the determination of cadmium, zinc, lead, copper, nickel, cobalt, and silver in seawater. In this procedure 500 ml of seawater taken in a plastic container is exposed to a 1000 W mercury arc lamp for 5-15 h to break down metal organic complexes. The solution is adjusted to pH 8, and 10 ml of 0.2% dithizone in chloroform added. The 10 ml of chloroform is run off and after adjustment to pH 9.5 the aqueous phase is extracted with a further 10 ml of dithizone. The combined extracts are washed with 50 ml of dilute ammonia. To the organic phases is added 50 ml of 0.2 M-hydrochloric acid. The phases are separated and the aqueous portion washed with 5 ml of chloroform. The aqueous portion is evaporated to dryness and the residue dissolved in 5 ml of 2 M hydrochloric acid (solution A). Perchloric acid (3 ml) is added to the organic portion, evaporated to dryness, and a further 2 ml of 60% perchloric acid added to ensure that all organic matter has been... 

Resonance Lamp.—Such lamps (sometimes called low pressure lamps) are often used as line sources in photochemical studies. These usually contain a small amount of a metal vapor (e.g., mercury, cadmium, zinc, etc.) and several mm pressure of a rare gas. They operate at relatively low current (ca. 100 ma.) and high voltages (several thousand volts). This is in contrast to a typical medium pressure lamp which may operate off a 110-220 v. power supply delivering ca. 3-5 amp. The most common example in photochemistry is the mercury resonance lamp which has strong emission of the unreversed resonance lines at 2537 A. and 1849 A. (ca. 90% or more of the total) along with other, much weaker lines ( resonance lines are those which appear both in absorption and emission). There is little continuum. Sources of this type are widely used for photosensitized reactions. 

Mercury is directly below cadmium in the periodic table, but has a considerably more varied and interesting chemistry than cadmium or zinc. Elemental mercury is the only metal that is a liquid at room temperature, and its relatively high vapor pressure contributes to its toxicological hazard. Mercury metal is used in electric discharge tubes (mercury lamps), gauges, pressure-sensing devices, vacuum pumps, valves, and seals. It was formerly widely used as a cathode in the chlor-alkali process for the manufacture of NaOH and Cl2, a process that has been largely discontinued, in part because of the mercury pollution that resulted from it. 

Most of these fixed-wavelength detectors can be filtered with a series of filters and or phosphors to detect at wavelengths varying from 280 to 546 nm. Wavelengths in the range 214-229 nm can be monitored by the use of zinc and cadmium source lamps, respectively [46]. 

The absorption line profile in the atomizer (e.g. in the flame) will still peak at the initial emission line peak. Absorbance will be reduced as the emission line becomes broader, and even more dramatically when the emission line shows reversal. Thus atomic absorption signal decreases with increasing lamp current (Figure 2). As might be expected, the drop off in signal is greater for more volatile elements such as cadmium and zinc. 

While the first hollow cathode tubes were constructed in such a way that they could be repeatedly flushed with the purified noble gas, the inconvenience connected with such equipment led to the development of permanently sealed tubes. In order to insure a reasonable lifetime of such tubes, they have to be of a certain minimum volume. One of the reasons for the lifetime limits is leakage of air into the tube, but more important seems to be the loss of the filler gas which is slowly absorbed by the metal and the glass surface. Since the lamp operates by the sputtering off of the cathode lining, gradual loss of the latter leads to eventual deterioration of the lamp. Lamps for metals that sputter abundantly, like the alkali metals, or zinc and cadmium, have short lifetimes, mostly well below a hundred hours. 

Fixed-wavelength detector using mercury, zinc, or cadmium lamps with wavelength selection by filters... 

Resonance lamps of the alkali metals, zinc and cadmium have been constructed. Laidler shows how Hg, Zn and Cd lamps may be put to very good use to place limits on bond energies and to determine the mechanisms of some photo-sensitised reactions. However, none of these lamps has been used extensively and have limited (or no) photochemical use. 

Osram lamps for mercury cannot be used in atomic absorption, because they contain vapor at so high a pressure that the emission line is almost completely self-absorbed, and the sensitivity is very small. It is also generally agreed that hollow-cathode lamps for thallium, zinc, and cadmium are superior to the discharge lamps. 

---