Second ionization

The apparent diffusion coefficient of the weak electrolyte is concentration dependent, the result of the solute-solute association. The physical significance of this concentration dependence may be clearer if we consider two limits. First, in dilute solutions AKCt apparent coefficient equals D, the ionic value. This makes sense because dilute solutions will show complete ionization. Second, in concentrated solution AKC-i 1), the apparent coefficient reduces to D2. molecular diffusion is paramount. Thus concentration-dependent diffusion of weak electrolytes shown by Fig. 6.2-2 reflects association. 

Figure Bl.7.7. Summary of the other collision based experiments possible with magnetic sector instruments (a) collision-mduced dissociation ionization (CIDI) records the CID mass spectrum of the neutral fragments accompanying imimolecular dissociation (b) charge stripping (CS) of the incident ion beam can be observed (c) charge reversal (CR) requires the ESA polarity to be opposite that of the magnet (d) neutiiralization-reionization (NR) probes the stability of transient neutrals fonned when ions are neutralized by collisions in the first collision cell. Neutrals surviving to be collisionally reionized in the second cell are recorded as recovery ions in the NR mass spectrum.

In contrast to the ionization of C q after vibrational excitation, typical multiphoton ionization proceeds via the excitation of higher electronic levels. In principle, multiphoton ionization can either be used to generate ions and to study their reactions, or as a sensitive detection technique for atoms, molecules, and radicals in reaction kinetics. The second application is more common. In most cases of excitation with visible or UV laser radiation, a few photons are enough to reach or exceed the ionization limit. A particularly important teclmique is resonantly enlianced multiphoton ionization (REMPI), which exploits the resonance of monocluomatic laser radiation with one or several intennediate levels (in one-photon or in multiphoton processes). The mechanisms are distinguished according to the number of photons leading to the resonant intennediate levels and to tire final level, as illustrated in figure B2.5.16. Several lasers of different frequencies may be combined. 

Micellization is a second-order or continuous type phase transition. Therefore, one observes continuous changes over the course of micelle fonnation. Many experimental teclmiques are particularly well suited for examining properties of micelles and micellar solutions. Important micellar properties include micelle size and aggregation number, self-diffusion coefficient, molecular packing of surfactant in the micelle, extent of surfactant ionization and counterion binding affinity, micelle collision rates, and many others. 

We can compare this result with the experimental first and second ionization potentials (IPs) for helium... 

If we compare the calculated total ionization potential, IP = 4.00 hartiees, with the experimental value, IP = 2.904 hartiees, the result is quite poor. The magnitude of the disaster is even more obvious if we subtract the known second ionization potential, IP2 = 2.00, from the total IP to find t c first ionization potential, IPi. The calculated value of IP2, the second step in reaction (8-21) is IP2 = Z /2 = 2.00, which is an exact result because the second ionization is a one-election problem. For the first step in reaction (8-21), IPi (calculated) = 2.00 and IPi(experimental) = 2.904 — 2.000 =. 904 hartiees, so the calculation is more than 100% in error. Clearly, we cannot ignore interelectronic repulsion. 

Ultraviolet photoelectron spectroscopy allows the determination of ionization potentials. For thiazole the first experimental measurement using this technique was preformed by Salmona et al. (189) who later studied various alkyl and functional derivatives in the 2-position (190,191). Substitution of an hydrogen atom by an alkyl group destabilizes the first ionization potential, the perturbation being constant for tso-propyl and heavier substituents. Introduction in the 2-position of an amino group strongly destabilizes the first band and only slightly the second. 

Mass spectrometry can be used to determine ionization potentials by the method of Lossing (283). The values obtained can be compared with those found by photoelectron spectroscopy and those calculated by CNDO/S (134) or ab initio (131) methods using the Koopman theorem approximation. The first and second, ionization potentials concern a ir... 

Example The pK s for the first and second ionizations of sulfuric acid are —48 and 2 0 respectively Sulfuric acid (HOSO2OH) is a strong acid hydrogen sulfate ion (H0S020 ) is a weak acid... 

As with other dicarboxyhc acids the second ionization constant of carbonic acid IS far smaller than the first... 

II, second spectra from singly ionized atoms, and so on for successive stages of ionization. 

Much of the energy deposited in a sample by a laser pulse or beam ablates as neutral material and not ions. Ordinarily, the neutral substances are simply pumped away, and the ions are analyzed by the mass spectrometer. To increase the number of ions formed, there is often a second ion source to produce ions from the neutral materials, thereby enhancing the total ion yield. This secondary or additional mode of ionization can be effected by electrons (electron ionization, El), reagent gases (chemical ionization. Cl), a plasma torch, or even a second laser pulse. The additional ionization is often organized as a pulse (electrons, reagent gas, or laser) that follows very shortly after the... 

Lasers can be used in either pulsed or continuous mode to desorb material from a sample, which can then be examined as such or mixed or dissolved in a matrix. The desorbed (ablated) material contains few or sometimes even no ions, and a second ionization step is frequently needed to improve the yield of ions. The most common methods of providing the second ionization use MALDI to give protonated molecular ions or a plasma torch to give atomic ions for isotope ratio measurement. By adjusting the laser s focus and power, laser desorption can be used for either depth or surface profiling. 

The particle beam — after linear passage from the evacuation chamber nozzle, through the first and second skimmers, and into the end of the ion source — finally passes through a heated grid immediately before ionization. The heated grid has the effect of breaking up most of the residual small clusters, so residual solvent evaporates and a beam of solute molecules enters the ionization chamber. 

There are methods for vaporizing solids of low volatility by placing them on a thin wire, which is then raised to a high temperature within a fraction of a second (direct chemical ionization, DCI). This rapid heating allows some vaporization without decomposition, but with the development of later ionization methods, it is now rarely used. 

The above direct process does not produce a high yield of ions, but it does form many molecules in the vapor phase. The yield of ions can be greatly increased by applying a second ionization method (e.g., electarn ionization) to the vaporized molecules. Therefore, laser desorption is often used in conjunction with a second ionization step, such as electron ionization, chemical ionization, or even a second laser ionization pulse. 

When ionization occurs, an incident electron collides with an atom, producing a positive ion and second electron. Thus two electrons appear after collision where there was only one initially. 

---