Ionic polymerizations rates

The initiators which are used in addition polymerizations are sometimes called catalysts, although strictly speaking this is a misnomer. A true catalyst is recoverable at the end of the reaction, chemically unchanged. Tliis is not true of the initiator molecules in addition polymerizations. Monomer and polymer are the initial and final states of the polymerization process, and these govern the thermodynamics of the reaction the nature and concentration of the intermediates in the process, on the other hand, determine the rate. This makes initiator and catalyst synonyms for the same material The former term stresses the effect of the reagent on the intermediate, and the latter its effect on the rate. The term catalyst is particularly common in the language of ionic polymerizations, but this terminology should not obscure the importance of the initiation step in the overall polymerization mechanism. 

In ionic polymerizations, reaction rates are faster in solvents with high dielectric constants, which promote the separation of the ion pair. 

The nature of the gegen ion is probably of the greatest importance in determining the rate of propagation in ionic polymerization. However, it is not clear whether the presence of the gegen ion enhances or inhibits the propagation. One may argue that the... 

Ethylene in Xenon Rate Constants for Ionic Polymerization. 

Phenomenological evidence for the participation of ionic precursors in radiolytic product formation and the applicability of mass spectral information on fragmentation patterns and ion-molecule reactions to radiolysis conditions are reviewed. Specific application of the methods in the ethylene system indicates the formation of the primary ions, C2H4+, C2i/3+, and C2H2+, with yields of ca. 1.5, 1.0, and 0.8 ions/100 e.v., respectively. The primary ions form intermediate collision complexes with ethylene. Intermediates [C4iZ8 + ] and [CJH7 + ] are stable (<dissociation rate constants <107 sec.-1) and form C6 intermediates which dissociate rate constants <109 sec. l). The transmission coefficient for the third-order ion-molecule reactions appears to be less than 0.02, and such inefficient steps are held responsible for the absence of ionic polymerization. 

Radiolytic ethylene destruction occurs with a yield of ca. 20 molecules consumed/100 e.v. (36, 48). Products containing up to six carbons account for ca. 60% of that amount, and can be ascribed to free radical reactions, molecular detachments, and low order ion-molecule reactions (32). This leaves only eight molecules/100 e.v. which may have formed ethylene polymer, corresponding to a chain length of only 2.1 molecules/ ion. Even if we assumed that ethylene destruction were entirely the result of ionic polymerization, only about five ethylene molecules would be involved per ion pair. The absence of ionic polymerization can also be demonstrated by the results of the gamma ray initiated polymerization of ethylene, whose kinetics can be completely explained on the basis of conventional free radical reactions and known rate constants for these processes (32). An increase above the expected rates occurs only at pressures in excess of ca. 20 atmospheres (10). The virtual absence of ionic polymerization can be regarded as one of the most surprising aspects of the radiation chemistry of ethylene. 

Table 2. Rate constants of propagation for ionic polymerization...

Ionic Polymerization. Ionic polymerizations, especially cationic polymerizations, are not as well understood as radical polymerizations because of experimental difficulties involved in their study. The nature of the reaction media is not always clear since heterogeneous initiators are often involved. Further, it is much more difficult to obtain reproducible data because ionic polymerizations proceed at very fast rates and are highly sensitive to small concentrations of impurities and adventitious materials. Butyl rubber, a polymer of isobutene and isoprene, is produced commercially by cationic polymerization. Anionic polymerization is used for various polymerizations of 1,3-butadiene and isoprene. 

Compared with free radical polymerizations, the kinetics of ionic polymerizations are not well defined. Reactions can use heterogeneous initiators and they are usually quite sensitive to the presence of impurities. Thus, kinetic studies are difficult and the results sensitive to the particular reaction conditions. Further, the rates of polymer formation are more rapid. 

It is appropriate at this point to briefly discuss the experimental procedures used to determine polymerization rates for both step and radical chain polymerizations. Rp can be experimentally followed by measuring the change in any property that differs for the monomer(s) and polymer, for example, solubility, density, refractive index, and spectral absorption [Collins et al., 1973 Giz et al., 2001 McCaffery, 1970 Stickler, 1987 Yamazoe et al., 2001]. Some techniques are equally useful for step and chain polymerizations, while others are more appropriate for only one or the other. Techniques useful for radical chain polymerizations are generally applicable to ionic chain polymerizations. The utility of any particular technique also depends on its precision and accuracy at low, medium, and high percentages of conversion. Some of the techniques have the inherent advantage of not needing to stop the polymerization to determine the percent conversion, that is, conversion can be followed versus time on the same reaction sample. 

The method used in drawing the ionic species in these two equations and throughout this chapter is meant to show that the ionic species usually do not exist as free ions but as ion pairs. The parentheses around the anionic fragment is used to indicate that the negative counterion remains close to the positive fragment. (Even when the counterion is not shown, one should understand it is present.) However, keep in mind that free ions coexist with the ion pairs, and it is the relative concentrations that determine the overall polymerization rate. 

In contrast to radical polymerizations, ionic polymerizations proceed at high rates even at low temperatures, since the initiation and propagation reactions have only small activation energies. For example, isobutylene is polymerized commercially with boron trifluoride in liquid propane at -100 °C (see Example 3-16). The polymerization temperature often has a considerable influence on the structure of the resulting polymer. 

P n is a reactive molecule of the polymer with n monomer units in the chain, and it is unimportant whether the polymerization mechanism is radical or ionic. The rate constant of the propagation step is kp. Under certain conditions, monomer units can be split off the reactive polymer molecule. Then it is necessary to consider also the depolymerization reaction (with the rate constant kd). 

---