Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Indicator product analysis method

The main idea of research is application of accessible, simple and express methods that don t need expensive reagent techniques for analysis of phanuaceutical products based on bischofite. The determination of metal ions such as Mg, Zn, Cu, Fe by complex-formation titrations using a widely applicable chelating agent, EDTA, have been studied as a function of pH, complexing agents and indicators. The analysis consists of four parts ... [Pg.396]

Laser desorption methods (such as LD-ITMS) are indicated as cost-saving real-time techniques for the near future. In a single laser shot, the LDI technique coupled with Fourier-transform mass spectrometry (FTMS) can provide detailed chemical information on the polymeric molecular structure, and is a tool for direct determination of additives and contaminants in polymers. This offers new analytical capabilities to solve problems in research, development, engineering, production, technical support, competitor product analysis, and defect analysis. Laser desorption techniques are limited to surface analysis and do not allow quantitation, but exhibit superior analyte selectivity. [Pg.737]

Many X-ray data are given for these bicyclic 5-6 systems, as a method for structure confirmation or elucidation of unexpected reaction products. Analysis of compound 25 (Scheme 5) revealed a planar molecule, in which the B-N distances (1.420 and 1.429 A) indicate a multiple bond character, since in diazaboroles they range from 1.395 to 1.450 A... [Pg.592]

Patil et al. [46] developed a simple, rapid, and precise stability-indicating liquid chromatographic method for analysis of lornoxicam in pharmaceutical dosage forms. Chromatographic separation of drug and its degradation products was achieved on a Cig analytical column with... [Pg.233]

The incidence of perceptible formaldehyde in homes, offices and schools has caused widespread uncertainty about the safety of living with formaldehyde. This uncertainty was enhanced by the large scale installation of urea formaldehyde foam insulation (UFFI) because a substantial part of this material was made from small scale resin batches prepared under questionable quality control conditions, and was installed by unskilled operators (10). The only reliable way to avoid such uncertainty is to know the emission rate of products and develop a design standard that allows prediction of indoor air levels. The first and most important step in this direction was achieved with the development and implementation of material emission standards. As indicated above, Japan led the field in 1974 with the introduction of the 24-hr desiccator test (6), FESYP followed with the formulation of the perforator test, the gas analysis method, and later with the introduction of air chambers (5). In the U.S. the FTM-1 (32) production test and the FTM-2 air chamber test (33) have made possible the implementation of a HUD standard for mobile homes (8) that is already implemented in some 90% of the UF wood production (35), regardless of product use. [Pg.224]

Sometimes a trend is detected between the vials a systematic increase or decrease in the content of an element or substance appears between vials. Two explanations are possible. Either the production of the material has suffered from a drift or the measurement method has itself drifted. To differentiate between both reasons, the analyst must perform the measurements between samples in a non chronological manner. As samples should be taken regularly during the packaging procedure and are labelled it is possible to arrange their analysis in a randomised way. If a random selection is performed for the between bottles test the drift in production may be overlooked. Figure 4.8 illustrates the differences in conclusion in case of production and method drift. It indicates that in addition to the dispersion of the results, the analyst must also identify the evolution of the results in terms of absolute quantity. [Pg.147]

Although the formidable difficulties associated with isotope separation schemes based on photochemical vibrational excitation plus chemical reaction continue to attract considerable attention, some earlier hopes appear to have been dashed. An experiment performed in 1970 by Mayer et al. has been much quoted. They reported irradiating mixtures of CHjOH and CD3OD in the presence of Bts with lines from an HF laser that are absorbed only by CH3OH. Product analysis indicated the selective depletion of the CH3OH. This observation was interpreted in terms of a selective reaction between vibrationally excited CH3OM and Bra, nnd it appeared to point the way to an economic method for the production of heavy water. However, the results of a careful re-examination of this system have just... [Pg.6]

A balanced chemical reaction indicates the quantitative relationships between the moles of reactants and products. These stoichiometric relationships provide the basis for many analytical calculations. Consider, for example, the problem of determining the amount of oxalic acid, H2C2O4, in rhubarb. One method for this analysis uses the following reaction in which we oxidize oxalic acid to CO2. [Pg.20]


See other pages where Indicator product analysis method is mentioned: [Pg.20]    [Pg.262]    [Pg.553]    [Pg.4]    [Pg.264]    [Pg.286]    [Pg.293]    [Pg.963]    [Pg.963]    [Pg.99]    [Pg.33]    [Pg.664]    [Pg.190]    [Pg.350]    [Pg.200]    [Pg.154]    [Pg.350]    [Pg.33]    [Pg.1113]    [Pg.8]    [Pg.91]    [Pg.27]    [Pg.158]    [Pg.1042]    [Pg.137]    [Pg.341]    [Pg.113]    [Pg.139]    [Pg.130]    [Pg.756]    [Pg.662]    [Pg.2113]    [Pg.384]    [Pg.437]    [Pg.126]    [Pg.317]    [Pg.43]    [Pg.30]    [Pg.186]    [Pg.579]    [Pg.338]    [Pg.1328]   
See also in sourсe #XX -- [ Pg.309 ]




SEARCH



Indicator methods

Indicator product analysis

Indicators analysis

Production method

Products, analysis

© 2024 chempedia.info