Heat treating oil

Lubricant fraction C26-C38 Gear and machinery lubricating oils, cutting and heat-treating oils, lubricating greases, medicinal jelly, paraffin waxes 2-3 1-2 1-2... 

To provide raw material for this comparative study of untreated and heat-treated oils, asphaltenes from Cold Lake crude (crude asphaltenes) and from Cold Lake vacuum residuum (residuum asphaltenes) were prepared by n-heptane precipitation as described in the Experimental section. The Cold Lake residuum fraction was prepared by Imperial Oil Enterprises, Ltd. at Sarnia, Ontario, Canada. The distillation history of this bottoms fraction indicates that the pot material was subjected to temperatures as high as 314-318°C during atmospheric and vacuum distillation. The length of time at 300°C or higher was about two hours. This is well in excess of what would be experienced in a pipestill and should have provided ample time for any decomposition. It should be noted, however, that since it was possible to maintain the system vacuum at 0.35 mm, the maximum temperature experienced by the residuum was not quite as high as it might be during refinery distillation (e.g. ca 350°C). 

Large differences in permeability, absorption and solubility were reported for the films of untreated alkaU-refined oil and heat-treated oils. However, it is not possible to make a direct comparison between the physical and chemical characteristics of a series of oils and the physical properties of films made from these oils, as there are a large number of variables involved. 

It was the general need to clean carbonaceous residues from heat treated metals by spraying/soaking them in hot oil which led to cleaning machines in which the pressure was elevated above ambient. Other soil materials about which there was the same need were asphaltine tars, coke residue, aged grease, oxidized heat treat oils, waxy carriers, etc. 

OIL MIST (MINERAL) Mist of white mineral oiL cutting oil, heat-treating oil, hydraulic oil, cable oil, lubricating oil None hazardous 275 NA NA... 

Cacahuananche Oil n This oil is obtained from the nuts of the tree, Licania arhorea. So far as the usual laboratory tests are concerned, this oil and Brazilian oiticica oil are much alike. The raw oil becomes lard-like on aging but may be permanently liquefied by heat. The raw and lightly heat-treated oil wrinkles as it dries, similarly to oiticica and tung oils. 

TI-6AI-4V ELI beta annealed Ti-6-22-22 beta forged Ti-6-22-22 beta heat treated (fan cool) Ti-6-22-22 beta heat treated(oil quench)... 

Steam is injected into a reservoir to reduce oil viscosity and make it flow more easily. This technique is used in reservoirs containing high viscosity crudes where conventional methods only yield very low recoveries. Steam can be injected in a cyclic process in which the same well is used for injection and production, and the steam is allowed to soak prior to back production (sometimes known as Huff and Puff). Alternatively steam is injected to create a steam flood, sweeping oil from injectors to producers much as in a conventional waterflood. In such cases it is still found beneficial to increase the residence (or relaxation) time of the steam to heat treat a greater volume of reservoir. 

Heat-transfer media Heat-transfer medium Heat-transfer oils Heat-transfer view Heat treating polyester Heat treatment Heavy crude oil Heavy-duty engines Heavy fuel oil Heavy gas oil Heavy metal Heavy metals... 

Steam treatment imparts increased corrosion resistance for ferrous P/M parts. The parts are heated to 400—600°C and then exposed to superheated steam. After cooling, the parts are usually oil dipped to further increase corrosion and wear resistance, and to enhance appearance (see Corrosion and CORROSION control). Heat treated parts are seldom steam treated because annealing reduces hardness and tensile strength. 

Mixtures containing various concentrations of mono-, di-, and polyisopropylnaphthalenes have been prepared by treating molten naphthalene with concentrated sulfuric acid and propjiene at 150—200°C followed by distillation (39). Products comprised of such isomeric mixtures have extremely low pour points, ie, ca —50° C, are excellent multipurpose solvents, and have been evaluated as possible Hquid-phase heat-transfer oils. 

Heavy fuel oil usually contains residuum that is mixed (cut back) to a specified viscosity with gas oils and fractionator bottoms. For some industrial purposes in which flames or flue gases contact the product (eg, ceramics, glass, heat treating, and open hearth furnaces), fuel oils must be blended to low sulfur specifications low sulfur residues are preferable for these fuels. 

Insiilating refractories are used mainly in the heat-treating industiy for furnaces of the periodic type. They are also used extensively in stress-relieving furnaces, chemical-process furnaces, oil stills or heaters, and the combustion chambers of domestic-oil-burner furnaces. They usually have a hfe equal to that of the heavy brick that they replace. They are particularly smtable for constructing experi-... 

The optimum precipitate is obtained by a more elaborate heal treatment the alloy is solution heat-treated (heated to dissolve the impurity), quenched (cooled fast to room temperature, usually by dropping it into oil or water) and finally tempered or aged for a controlled time and at a controlled temperature (to cause the precipitate to form). 

Indirect fired heaters (sometimes called line heaters) heat the gas stream before and/or after the choke so that the gas is maintained above the hydrate temperature. Indirect fired heaters can also be used to heat crude oil for treating, heat a hot fluid circulating medium (heat medium) that is used to provide process heat, etc. 

This term is used to describe oils that have a flash point above ambient temperature. They will therefore not burn or explode at ambient temperature but will do so when hot. Unfortunately many people do not realize this and treat heavy oils with a disrespect that they would never apply to gasoline, as shown by the incidents described below. Another incident was described in Section 12.2 (c). Heavy oils are widely used as fuel oils, solvents, lubricants, and heat transfer oils, as well as process materials. 

The bulk flotation can be accomplished with the addition of small doses of oleic acid plus oxidized emulsion of fuel oil. The fuel oil is treated with 10% solution of NaOH at a temperature of 60-80°C for 1 h. The following method was used for rutile-zircon separation the concentrate was thickened, followed by heat conditioning to 60°C. After the heat treatment, the zircon was floated without the addition of collector. The zirconium tailing is the rutile concentrate. The zircon concentrate was thickened, followed by gravity cleaning. In some cases, the heat-treated pulp is washed before zircon flotation. The following metallurgical results were obtained ... 

In the atmospheric distillation process (Figure 2.1), heated crude oil is separated in a distillation column (distillation tower, fractionating tower, atmospheric pipe still) into streams which are then purified, transformed, adapted, and treated... 

In contrast, the facilities of the 2 other operators consisted of 89 conventional tank batteries. Production from approximately 270 wells produced into conventional separation and heat treating equipment and then to gunbarrels and settling tanks for clean oil processing. Clean oil was transferred... 

---