Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Suspensions heat transfer

Fluidized-bed catalytic reactors. In fluidized-bed reactors, solid material in the form of fine particles is held in suspension by the upward flow of the reacting fluid. The effect of the rapid motion of the particles is good heat transfer and temperature uniformity. This prevents the formation of the hot spots that can occur with fixed-bed reactors. [Pg.58]

In a suspension polymerisation monomer is suspended in water as 0.1—5-mm droplets, stabilised by protective coUoids or suspending agents. Polymerisation is initiated by a monomer-soluble initiator and takes place within the monomer droplets. The water serves as both the dispersion medium and a heat-transfer agent. Particle sise is controlled primarily by the rate of agitation and the concentration and type of suspending aids. The polymer is obtained as small beads about 0.1—5 mm in diameter, which are isolated by filtration or centrifugation. [Pg.169]

Aqueous media, such as emulsion, suspension, and dispersion polymerization, are by far the most widely used in the acryUc fiber industry. Water acts as a convenient heat-transfer and cooling medium and the polymer is easily recovered by filtration or centrifugation. Fiber producers that use aqueous solutions of thiocyanate or zinc chloride as the solvent for the polymer have an additional benefit. In such cases the reaction medium can be converted directiy to dope to save the costs of polymer recovery. Aqueous emulsions are less common. This type of process is used primarily for modacryUc compositions, such as Dynel. Even in such processes the emulsifier is used at very low levels, giving a polymerization medium with characteristics of both a suspension and a tme emulsion. [Pg.279]

Copolymerization is effected by suspension or emulsion techniques under such conditions that tetrafluoroethylene, but not ethylene, may homopolymerize. Bulk polymerization is not commercially feasible, because of heat-transfer limitations and explosion hazard of the comonomer mixture. Polymerizations typically take place below 100°C and 5 MPa (50 atm). Initiators include peroxides, redox systems (10), free-radical sources (11), and ionizing radiation (12). [Pg.365]

The effective thermal conductivity of a Hquid—soHd suspension has been reported to be (46) larger than that of a pure Hquid. The phenomenon was attributed to the microconvection around soHd particles, resulting in an increased convective heat-transfer coefficient. For example, a 30-fold increase in the effective thermal conductivity and a 10-fold increase in the heat-transfer coefficient were predicted for a 30% suspension of 1-mm particles in a 10-mm diameter pipe at an average velocity of 10 m/s (45). [Pg.499]

Polymerization in Hquid monomer was pioneered by RexaH Dmg and Chemical and Phillips Petroleum (United States). In the RexaH process, Hquid propylene is polymerized in a stirred reactor to form a polymer slurry. This suspension is transferred to a cyclone to separate the polymer from gaseous monomer under atmospheric pressure. The gaseous monomer is then compressed, condensed, and recycled to the polymerizer (123). In the Phillips process, polymerization occurs in loop reactors, increasing the ratio of available heat-transfer surface to reactor volume (124). In both of these processes, high catalyst residues necessitate post-reactor treatment of the polymer. [Pg.414]

From the beer weU, the residue—alcohol suspension passes through a preheater where it is warmed by heat transfer from the vapors leaving the stiU. The preheated beer is then ready for distiUation. The condensate from the preheater is returned to the beer stiU. [Pg.84]

The chlorine and ethane are brought together in a fluid bed of finely divided, inert, solid heat-transfer medium, eg, sand, at 380—440°C the linear velocity of the gas is sufficient to maintain the finely divided solid in suspension within the reactor (26). [Pg.3]

Suspension Polymerization. This method (10) might be considered as a number of bulk polymerizations carried out simultaneously in the monomer droplets with water acting as a heat-transfer medium. A monomer-soluble initiator, eg, a peroxide or azo compound, and a protective coUoid like poly(vinyl alcohol) or bentonite, are requited. After completion of the polymerization, the excess of monomer(s) is steam stripped, and the beads of polymer are collected and washed on a centrifiige or filter and dried on a vibrating screen or by means of an expeUer—extmder. [Pg.474]

Pafticulate fouling. Particles held in suspension in the flow stream will deposit out on the heat-transfer surface in areas of sufficiently lower velocity. [Pg.1053]

Product Quality Considerations of product quahty may require low holdup time and low-temperature operation to avoid thermal degradation. The low holdup time eliminates some types of evaporators, and some types are also eliminated because of poor heat-transfer charac teristics at low temperature. Product quality may also dic tate special materials of construction to avoid met hc contamination or a catalytic effect on decomposition of the product. Corrosion may also influence evaporator selection, since the advantages of evaporators having high heat-transfer coefficients are more apparent when expensive materials of construction are indicated. Corrosion and erosion are frequently more severe in evaporators than in other types of equipment because of the high hquid and vapor velocities used, the frequent presence of sohds in suspension, and the necessary concentration differences. [Pg.1138]

For suspension of free-settling particles, circulation of pseudoplastic slurries, and heat transfer or mixing of miscible liqiiids to obtain uniformity, a speed of 3.50 or 420 r/min should be stipulated. For dispersion of dry particles in hquids or for rapid initial mixing of hquid reactants in a vessel, an 11.50- or 1750- r/min propeller should be used at a distance Df/4 above the vessel bottom. A second propeller can be added to the shaft at a depth below the hquid surface if the submergence of floating hquids or particiilate solids is other wise inadequate. Such propeller mixers are readily available up to 2.2 kW (3 hp) for off-center sloped-shaft mounting. [Pg.1631]

Stirred Vessels Gases may be dispersed in hquids by spargers or nozzles and redispersed by packing or trays. More intensive dispersion and redispersion is obtained by mechanical agitation. At the same time, the agitation will improve heat transfer and will keep catalyst particles in suspension if necessaiy. Power inputs of 0.6 to 2.0 kW/m (3.05 to 10.15 np/1,000 gal) are suitable. [Pg.2110]

Suspension polymerisation of styrene is widely practised commercially. In this process the monomer is suspended in droplets 5 -Min. in diameter in a fluid, usually water. The heat transfer distances for the dissipation of the exotherm are thus reduced to values in the range s-fisin. Removal of heat from the low-viscosity fluid medium presents little problem. The reaction is initiated by monomer-soluble initiators such as benzoyl peroxide. [Pg.431]

Table 7-4 shows flow patterns and applications of some commercially available impellers. Generally, the axial flow pattern is most suitable for flow sensitive operation such as blending, heat transfer, and solids suspension, while the radial flow pattern is ideal for dispersion operations that require higher shear levels than are provided by axial flow impellers. Myers et al. [5] have described a selection of impellers with applications. Further details on selection are provided by Uhl and Gray [6], Gates et al. [7], Hicks et al. [8] and Dickey [9]. [Pg.566]

The essential feature of a Jluidized-bed reactor is that the solids are held in suspension by the upward flow of the reacting fluid this promotes high mass and heat transfer rates and good mixing. Heat transfer coefficients in the order of 200 W/m-°C between jackets and internal coils are typically obtained. The solids may be a catalyst, a reactant (in some fluidized combustion processes), or an inert powder added to promote heat transfer. [Pg.136]

Primarily for flow controlled requirements, such as solids suspensions, heat transfer, and other high pumping efficiency applications. [Pg.291]

Scale-up techniques for using the results of pilot plant or bench scale test w ork to establish the equivalent process results for a commercial or large scale plant mixing system design require careful specialized considerations and usually are best handled by the mixer manufacturer s specialist. The methods to accomplish scale-up will vary considerably, depending on whether the actual operation is one of blending, chemical reaction tvith product concentrations, gas dispersions, heat transfer, solids suspensions, or others. [Pg.312]

Operations such as blending, solids-suspension, dissolving, heat transfer and liquid-liquid extraction are typical of systems requiring high flow relative to turbulence, while gas-liquid reactions and some liquid-liquid contacting require high turbulence relative to flow. The case of (1) 100% of suspension—requires head to keep particles suspended and (2) 100% uniformity of distribution of particles—requires head for suspension plus flow for dis-tiibution. [Pg.323]

In experiments with bubble-columns containing suspended sand particles with average diameter 0.12 mm, an increase in heat-transfer coefficient was observed with increasing sand concentration, maximum values of 6000 kcal/m2-hr-°C being measured for suspensions containing 50% sand (based on the liquid volume). [Pg.118]


See other pages where Suspensions heat transfer is mentioned: [Pg.17]    [Pg.17]    [Pg.196]    [Pg.499]    [Pg.207]    [Pg.109]    [Pg.118]    [Pg.262]    [Pg.428]    [Pg.462]    [Pg.472]    [Pg.474]    [Pg.1138]    [Pg.1205]    [Pg.1630]    [Pg.1668]    [Pg.2104]    [Pg.435]    [Pg.102]    [Pg.554]    [Pg.63]    [Pg.135]    [Pg.190]    [Pg.288]    [Pg.289]    [Pg.481]    [Pg.288]    [Pg.289]   
See also in sourсe #XX -- [ Pg.125 , Pg.126 , Pg.127 , Pg.128 ]




SEARCH



Agitation and Heat Transfer in Suspensions

Solid-liquid, suspension heat transfer

Suspension density, heat transfer

Suspension-surface heat transfer

Suspensions to surface heat transfer

Wall-to-suspension heat transfer

© 2024 chempedia.info