Gloves removing

Skin MAY BE ABSORBED Skin burns. Pain. (Further see Inhalation). Protective gloves. Remove contaminated clothes. Rinse and then wash skin with water and soap. Refer for medical attention. 

Skin Protective gloves. Remove contaminated clothes. Rinse and then wash skin with water and soap. 

Skin Contact Don respiratory protective masks and gloves remove victim from agent source immediately flush skin and... 

Skin Contact Don respiratory protective masks and gloves remove victim from agent source immediately flush skin and clothes with 5% solution of sodium hypochlorite or liquid household bleach within 1 min cut and remove contaminated clothing flush contaminated skin area again with 5% sodium hypochlorite solution then wash contaminated skin area with soap and water seek medical attention immediately. Ingestion Do not induce vomiting give victim milk to drink seek medical attention immediately. 

Skin Contact Don respiratory mask and gloves remove victim from source immediately and remove contaminated clothing decontaminate the skin immediately by flushing with a 5% solution of liquid household bleach wash off with soap and water after 3-4 min to remove decon agent and protect against erythema seek medical attention immediately to prevent systemic toxicity, decontamination should be done as late as 2 or 3 h after exposure even if it increases the severity of the local reaction further cleans with soap and water. 

All PPE should be removed and disposed of in the hazardous waste chute or disposal bag when removing hands from the enclosure to prevent dragging powders out of the unit. Users should be trained in aseptic glove removal technique to minimize aerosolization of material during a process where skin could become exposed. 

Dermal Protective clothing, gloves Remove contaminated clothes and shoes immediately wash the area with soap or mild detergent and rinse thoroughly until no evidence of substance remains (15-20 min)... 

While wearing gloves, remove the polymer that forms and place it in the palm of one hand, as shown in Figure C. Gently press it with the... 

Station 4 Overboot and Glove Removal 1 attendant 2 30-gallon containers 100 trash bags Engineer tape Cutting tool... 

Ammonium Dichromate Ehist respirator, protective goggles, gloves. Remove to clean air and summon medical attention. Immediately flush with water for at least 15 minutes. If skin irritation develops, get medical attention. Immediately flush out with water and consult a physician. 

Ammonium Fluoride Dust mask, goggles or face shield, rubber gloves. Remove to fresh air. Shower immediately with large quantities of water. Remove all contaminated clothing. Consult a physician. Rush with water for at least 15 minutes. Consult a physician. 

Ammonium Lactate Dust mask, goggles or face shield, rubber gloves. Remove to fresh air. Flush with water. 

N-Butyl Acetate All-purpose canister mask, chemical safety goggles, rubber gloves. Remove from exposure immediately. Call a physician. If breathing is irregular or stopped, start resuscitation, administer oxygen. In case of contact, flush with water for at least 15 minutes. 

Cadmium Sulfate Respirator, goggles, rubber gloves. Remove victim from exposure and call physician. Wash with soap and water. Rush with water for at least 10 minutes consult physician. 

Ethyl Lactate Goggles or face shield rubber gloves. Remove victim to fresh air. Flush well with water. Rush well with water. 

Methyl Alcohol Approved canister mask for high vapor concentrations safety goggles rubber gloves. Remove victim from exposure and apply artificial respiration is breathing has ceased. Flush with water for 15 minutes. Flush with water for 15 minutes. 

Toluene Air-supplied mask, goggles and face shield, plastic gloves. Remove victim to fresh air and give artificial respiration and oxygen if needed. Call a doctor. Wipe off and wash with soap and water. Flush with water for at least 15 minutes. 

Zinc Ammonium Chloride Dust mask, goggles and face shield, protective gloves. Remove dust. ... 

Working at the hood and wearing rubber gloves, remove the rubber stopper from your 50-mL filter flask containing Br2, and pour some of the Br2 vapor into a dry 16 x 150-mm test tube just as you would pour water, being careful to avoid transfer of anv Br2 liguid. Replace the rubber stopper. 

---