Polar glasses

R Kurokawa, M. Soderstrom, A. Horlein, S. Halachmi, M. Brown, M. G. Rosenfeld, and C. K. Glass. Polarity-specific activities of retinoic acid receptors determined by a co-repressor [see comments). Nature, 377 (6548), 451- 54, 1995. 

Disclinations in tire nematic phase produce tire characteristic Schlieren texture, observed under tire microscope using crossed polars for samples between glass plates when tire director takes nonunifonn orientations parallel to tire plates. In thicker films of nematics, textures of dark flexible filaments are observed, whetlier in polarized light or not. This texture, in fact, gave rise to tire tenn nematic (from tire Greek for tliread ) [40]. The director fields... 

Fig. 1. A "barred olivine" chondrule from the Allende-type CV chondrite that feU in Mexico in 1979. The transmitted polarized light image of the 0.5 mm-diameter chondrule was taken from a poHshed thin section. The bars are composed of oHvine, (Mg,Fe)2Si04. The interstitial material is glass quenched...

Lithium hydride reacts vigorously with siUcates above 180°C. Therefore, glass, quart2, and porcelain containers cannot be used in preparative processes. That only traces dissolve in polar solvents such as ether reflects its significant (60—75%) covalent bond character. It is completely soluble in, and forms eutectic melting compositions with, a number of fused salts. 

Polar groups, eg, carbonyl and sulfonyl, that are capable of conjugation with the aromatic ring increase the glass-transition temperature, eg, to 245°C for the sulfonyl group, as in (5). 

The dielectric constant is a measure of the ease with which charged species in a material can be displaced to form dipoles. There are four primary mechanisms of polarization in glasses (13) electronic, atomic, orientational, and interfacial polarization. Electronic polarization arises from the displacement of electron clouds and is important at optical (ultraviolet) frequencies. At optical frequencies, the dielectric constant of a glass is related to the refractive index k =. Atomic polarization occurs at infrared frequencies and involves the displacement of positive and negative ions. 

At lower frequencies, orientational polarization may occur if the glass contains permanent ionic or molecular dipoles, such as H2O or an Si—OH group, that can rotate or oscillate in the presence of an appHed electric field. Another source of orientational polarization at even lower frequencies is the oscillatory movement of mobile ions such as Na". The higher the amount of alkaH oxide in the glass, the higher the dielectric constant. When the movement of mobile charge carriers is obstmcted by a barrier, the accumulation of carriers at the interface leads to interfacial polarization. Interfacial polarization can occur in phase-separated glasses if the phases have different dielectric constants. 

Once separated, the supports are washed using acid (HCl) and sdanized, ie, treated with dimethyl dichi orosilane [75-78-5] (DMCS), to reduce the polarity. Sdanizing replaces adjacent SiOH groups with nonpolar CH caps. In addition to diatomaceous earths, supports of carbon (qv), halocarbons, eg. Teflon, and glass beads are in use by various chromatographers. 

The highly polar nature of the TGMDA—DDS system results in high moisture absorption. The plasticization of epoxy matrices by absorbed water and its effect on composite properties have been well documented. As can be seen from Table 4, the TGMDA system can absorb as much as 6.5% (by weight) water (4). This absorbed water results in a dramatic drop in both the glass transition temperature and hot—wet flexural modulus (4—6). 

Dyes for Color Filters. Colorhquid crystal display systems consist of LSI drivers, glass plates, polarizers, electrodes (indium—tin oxide), and microcolor filters. The iadependent microcolor filter containing dyes is placed on each Hquid crystal pixel addressed electrically and acts as an iadividual light switch. All colors can be expressed by the light transmitted through each filter layer of the three primary colors, ie, red, green, and blue (Fig. 12). 

Fig. 12. General stmcture of LCD. A, polarizer plate B, glass plate C, electrodes (indium—tin oxide) D, Hquid crystal E, common electrode (ITO) F, overcoated layer G, colored pixel H, back light. In an improved color LCD system today, retardation films are placed between A and B.

This combination of monomers is unique in that the two are very different chemically, and in thek character in a polymer. Polybutadiene homopolymer has a low glass-transition temperature, remaining mbbery as low as —85° C, and is a very nonpolar substance with Htde resistance to hydrocarbon fluids such as oil or gasoline. Polyacrylonitrile, on the other hand, has a glass temperature of about 110°C, and is very polar and resistant to hydrocarbon fluids (see Acrylonitrile polymers). As a result, copolymerization of the two monomers at different ratios provides a wide choice of combinations of properties. In addition to providing the mbbery nature to the copolymer, butadiene also provides residual unsaturation, both in the main chain in the case of 1,4, or in a side chain in the case of 1,2 polymerization. This residual unsaturation is useful as a cure site for vulcanization by sulfur or by peroxides, but is also a weak point for chemical attack, such as oxidation, especially at elevated temperatures. As a result, all commercial NBR products contain small amounts ( 0.5-2.5%) of antioxidant to protect the polymer during its manufacture, storage, and use. 

When dipoles are directly attached to the chain their movement will obviously depend on the ability of chain segments to move. Thus the dipole polarisation effect will be much less below the glass transition temperature, than above it Figure 6.4). For this reason unplasticised PVC, poly(ethylene terephthalate) and the bis-phenol A polycarbonates are better high-frequency insulators at room temperature, which is below the glass temperature of each of these polymers, than would be expected in polymers of similar polarity but with the polar groups in the side chains. 

Figure 6.4. Power factor-temperature curves for three polar polymers whose polar groups are integral with or directly attached to the main chain. The rise in power factor above the glass transition point is clearly seen in these three examples...

---