Glass transition temperature thermal analysis

Thermal Properties. Spider dragline silk was thermally stable to about 230°C based on thermal gravimetric analysis (tga) (33). Two thermal transitions were observed by dynamic mechanical analysis (dma), one at —75° C, presumed to represent localized mobiUty in the noncrystalline regions of the silk fiber, and the other at 210°C, indicative of a partial melt or a glass transition. Data from thermal studies on B. mori silkworm cocoon silk indicate a glass-transition temperature, T, of 175°C and stability to around 250°C (37). The T for wild silkworm cocoon silks were slightly higher, from 160 to 210°C. 

The thermal glass-transition temperatures of poly(vinyl acetal)s can be determined by dynamic mechanical analysis, differential scanning calorimetry, and nmr techniques (31). The thermal glass-transition temperature of poly(vinyl acetal) resins prepared from aliphatic aldehydes can be estimated from empirical relationships such as equation 1 where OH and OAc are the weight percent of vinyl alcohol and vinyl acetate units and C is the number of carbons in the chain derived from the aldehyde. The symbols with subscripts are the corresponding values for a standard (s) resin with known parameters (32). The formula accurately predicts that resin T increases as vinyl alcohol content increases, and decreases as vinyl acetate content and aldehyde carbon chain length increases. 

Network properties and microscopic structures of various epoxy resins cross-linked by phenolic novolacs were investigated by Suzuki et al.97 Positron annihilation spectroscopy (PAS) was utilized to characterize intermolecular spacing of networks and the results were compared to bulk polymer properties. The lifetimes (t3) and intensities (/3) of the active species (positronium ions) correspond to volume and number of holes which constitute the free volume in the network. Networks cured with flexible epoxies had more holes throughout the temperature range, and the space increased with temperature increases. Glass transition temperatures and thermal expansion coefficients (a) were calculated from plots of t3 versus temperature. The Tgs and thermal expansion coefficients obtained from PAS were lower titan those obtained from thermomechanical analysis. These differences were attributed to micro-Brownian motions determined by PAS versus macroscopic polymer properties determined by thermomechanical analysis. 

Glass transition temperature (Tg), measured by means of dynamic mechanical analysis (DMA) of E-plastomers has been measured in binary blends of iPP and E-plastomer. These studies indicate some depression in the Tg in the binary, but incompatible, blends compared to the Tg of the corresponding neat E-plastomer. This is attributed to thermally induced internal stress resulting from differential volume contraction of the two phases during cooling from the melt. The temperature dependence of the specific volume of the blend components was determined by PVT measurement of temperatures between 30°C and 270°C and extrapolated to the elastomer Tg at —50°C. 

Thermal Properties. The glass transition temperature (Tg) and the decomposition temperature (Td) were measured with a DuPont 910 Differential Scanning Calorimeter (DSC) calibrated with indium. The standard heating rate for all polymers was 10 °C/min. Thermogravimetric analysis (TGA) was performed on a DuPont 951 Thermogravimetric Analyzer at a heating rate of 20 °C/min. 

ASTM E 1356-98, ASTM Book of Standards 2002. Standard Test Method for Assignment of the Glass Transition Temperature by Differential Scanning Calorimetry or Differential Thermal Analysis . ASTM International, Conshohocken, PA. 

Temperature(s). See also Blackbody temperature sensor Cure temperature Curie temperature Eutectic temperature Fictive temperature Furnace temperature Glass- transition temperatures Heat entries Heating Hot entries Refrigeration Target temperature emperature measurement Thermal entries Thermo-entries Transition temperatures in analysis of water, 26 35 biofiltration system, 10 76 in biological wastewater treatment,... 

Thermal Analysis. The glass transition temperature, Tg, of each of the samples was determined by the use of an Omnitherm Q.C.25 Thermal Analyzer at a heating rate of 20°C/min. The midpoint of the inflection in the DSC output was taken as the Tg. 

The dynamic mechanical thermal analysis also indicated molecular mixing of the two components. The Tg of the thermoplastic was lower than the composite, as determined from the inflection point of the E curve seen in Figures 13 1. The PEOX glass transition temperature appeared at 62°C, while that for PVP showed up at ll5°C. The discrepancy in the Tg of PVP had already been addressed. The Tg extrapolated from the DMTA thermogram was reported since no artifacts were to be introduced. The samples exemplified for all DMTA thermograms were processed in a normalized fashion. Any thermal or hygroscopic Influences were eliminated. Some water may be trapped in the neat thermoplastics but this was minimized since they are hot pressed at 150°C and stored under calcium... 

The data indicate that the properties of the lower glass transition temperature metal ion modified polyimides are altered more than the properties of the higher glass transition temperature metal ion modified polyimides. Extraction removes both cobalt and chlorine from the films and slightly increases bulk thermal stability and both surface resistivity and bulk electrical resistivity. Details pertaining to the structure, analysis and properties of these novel gradient composites are discussed. 

The measurements of Young s modulus in dependence of the temperature (dynamic-mechanical measurements, see Sect. 2.3.5.2) and the differential thermal analysis (DTA or DSC) are the most frequently used methods for determination of the glass transition temperature. In Table 2.10 are listed and values for several amorphous and crystalline polymers. 

The glass transition temperature of sorbitol has also been studied using thermal analysis, and temperatures ranging from 0 to -55°C have been reported [8,20-24]. The temperature values were dependent on heating rate, history of the sample, and pressure. The extensive variation in conditions explains the wide range of temperatures reported for this parameter. 

The glass transition temperature can be measured in a variety of ways (DSC, dynamic mechanical analysis, thermal mechanical analysis), not all of which yield the same value [3,8,9,24,29], This results from the kinetic, rather than thermodynamic, nature of the transition [40,41], Tg depends on the heating rate of the experiment and the thermal history of the specimen [3,8,9], Also, any molecular parameter affecting chain mobility effects the T% [3,8], Table 16.2 provides a summary of molecular parameters that influence the T. From the point of view of DSC measurements, an increase in heat capacity occurs at Tg due to the onset of these additional molecular motions, which shows up as an endothermic response with a shift in the baseline [9,24]. 

Mijovic et al. analyzed the annealed blends from melts using dynamic mechanical thermal analysis and achieved similar results after an adjustment for shifting factors, AT s, as shown in Figure 7.3. The results were extended to include blends having a PVDF concentration greater than 80 wt %. It can be observed that the glass transition temperatures of the annealed blends reduce rapidly when the PVDF concentrations are above 80 wt %. 

The thermal analysis results (Figure 9.4) indicate that most of the materials show a clear phase segregation with two, distinct glass transition temperatures, indicated in Table 9.3 as and respectively. The Tg, value is around -80/ - 90°C close to, although somewhat higher than, that of the polyhydroxy... 

The glass transition temperatures ofthe polyimides are 195-250 °C their 10% weight loss temperamres (dynamic thermogravimetric analysis, air, AT = 4.5 °C/min) are 390-422 °C. Of particular interest are the dielectric constants of these polyimides. At a relative humidity of 50% these constants are 2.70-2.90 and are comparable with constants of the best fluorinated polyimides [21, 50-55]. The lowest dielectric constant (2.70) was observed for polyimide based on 6F dianhydride, containing the highest amount of fluorine. Thermal treatment of this polymer film at 280-290 °C for 1 hour led to a decrease (2.45) of dielectric constant due to the possible formation of nanofoams [56]. 

ISO 11359-2, 1999. Plastics - Thermomechanical analysis - Determination of coefficient of linear thermal expansion and glass transition temperature. 

---