Glass transition temperature butadienes

This type of adhesive is generally useful in the temperature range where the material is either leathery or mbbery, ie, between the glass-transition temperature and the melt temperature. Hot-melt adhesives are based on thermoplastic polymers that may be compounded or uncompounded ethylene—vinyl acetate copolymers, paraffin waxes, polypropylene, phenoxy resins, styrene—butadiene copolymers, ethylene—ethyl acrylate copolymers, and low, and low density polypropylene are used in the compounded state polyesters, polyamides, and polyurethanes are used in the mosdy uncompounded state. 

The glass-transition temperature in amorphous polymers is also sensitive to copolymerization. Generally, T of a random copolymer falls between the glass-transition temperatures of the respective homopolymers. For example, T for solution-polymerized polybutadiene is —that for solution-polymerized polystyrene is -HlOO°C. A commercial solution random copolymer of butadiene and styrene (Firestone s Stereon) shows an intermediate T of —(48). The glass-transition temperature of the random copolymer can sometimes be related simply as follows ... 

This combination of monomers is unique in that the two are very different chemically, and in thek character in a polymer. Polybutadiene homopolymer has a low glass-transition temperature, remaining mbbery as low as —85° C, and is a very nonpolar substance with Htde resistance to hydrocarbon fluids such as oil or gasoline. Polyacrylonitrile, on the other hand, has a glass temperature of about 110°C, and is very polar and resistant to hydrocarbon fluids (see Acrylonitrile polymers). As a result, copolymerization of the two monomers at different ratios provides a wide choice of combinations of properties. In addition to providing the mbbery nature to the copolymer, butadiene also provides residual unsaturation, both in the main chain in the case of 1,4, or in a side chain in the case of 1,2 polymerization. This residual unsaturation is useful as a cure site for vulcanization by sulfur or by peroxides, but is also a weak point for chemical attack, such as oxidation, especially at elevated temperatures. As a result, all commercial NBR products contain small amounts ( 0.5-2.5%) of antioxidant to protect the polymer during its manufacture, storage, and use. 

SBR is produced by addition copolymerization of styrene and butadiene monomers in either emulsion or solution process. The styrene/butadiene ratio controls the glass transition temperature (To) of the copolymer and thus its stiffness. T ... 

FIGURE 13.2 Calculated relation between the solubility parameter and glass transition temperature (Jg) for a variety of ethylene-propylene copolymers (EPMs) grafted with polar monomers the window for rubbers with an oil resistance similar to or better than hydrogenated acrylonitrile-butadiene copolymer (NBR) (20 wt% acrylonitrile) is also shown. 

Styrene co-butadiene is a rubbery amorphous polymer with a glass transition temperature well below room temperature. Polystyrene co-butadiene is an important component of several commercial families of plastic that contain polystyrene blocks. 

The polybutadienes prepared with these barium t-butoxide-hydroxide/BuLi catalysts are sufficiently stereoregular to undergo crystallization, as measured by DTA ( 8). Since these polymers have a low vinyl content (7%), they also have a low gl ass transition temperature. At a trans-1,4 content of 79%, the Tg is -91°C and multiple endothermic transitions occur at 4°, 20°, and 35°C. However, in copolymers of butadiene (equivalent trans content) and styrene (9 wt.7. styrene), the endothermic transitions are decreased to -4° and 25°C. Relative to the polybutadiene, the glass transition temperature for the copolymer is increased to -82°C. The strain induced crystallization behavior for a SBR of similar structure will be discussed after the introduction of the following new and advanced synthetic rubber. 

Several attempts have been made to superimpose creep and stress-relaxation data obtained at different temperatures on styrcne-butadiene-styrene block polymers. Shen and Kaelble (258) found that Williams-Landel-Ferry (WLF) (27) shift factors held around each of the glass transition temperatures of the polystyrene and the poly butadiene, but at intermediate temperatures a different type of shift factor had to be used to make a master curve. However, on very similar block polymers, Lim et ai. (25 )) found that a WLF shift factor held only below 15°C in the region between the glass transitions, and at higher temperatures an Arrhenius type of shift factor held. The reason for this difference in the shift factors is not known. Master curves have been made from creep and stress-relaxation data on partially miscible graft polymers of poly(ethyl acrylate) and poly(mcthyl methacrylate) (260). WLF shift factors held approximately, but the master curves covered 20 to 25 decades of time rather than the 10 to 15 decades for normal one-phase polymers. 

In blends of PTT and ABS, two separate glass transition temperatures are observed, which indicates that the blends are phase separated in the amorphous phase. A styrene/butadiene/maleic anhydride copolymer or glycidyl endcapped epoxy resin may act as a compatibilizer. Compatibilized PTT/ABS blends show a finer morphology and better adhesion between the phases. 

Siloxane elastomers present an attractive alternative to the butadiene acrylonitrile elastomers most often used for epoxy modification. Poly(dimethyl siloxanes) exhibit glass transition temperatures well below those of butadiene acrylonitrile modifiers (minimum —123 °C vs. about —40 °C) and also display very good thermal stability13, 14). Other favorable and potentially useful attributes include good weatherability, oxidative stability, and moisture resistance. Finally, the non-polar nature and low surface energy of poly(dimethyl siloxanes) constitute a thermodynamic driving force... 

RESINS (Acrylonitrile-Butadiene-Styrene). Commonly referred to as ABS resins, these materials are thermoplastic resins which are produced by grafting styrene and acrylonitrile onto a diene-rubber backbone. The usually preferred substrate is polybutadiene because of its low glass-transition temperature (approximately —80°C). Where ABS resin is prepared by suspension or mass polymerization methods, stereospedfic diene rubber made by solution polymerization is the preferred diene. Otherwise, the diene used is a high-gel or cross-linked latex made by a hot emulsion process. 

The thermal stability of poly(vinyl chloride) is improved greatly by the in situ polymerization of butadiene or by reaction with preformed cis-1,4-polybutadiene using a diethyl-aluminum chloride-cobalt compound catalyst system. The improved thermal stability at 3-10% add-on is manifested by greatly reduced discoloration when the modified poly-(vinyl chloride) is compression molded at 200°C in air in the absence of a stabilizer, hydrogen chloride evolution at 180°C is retarded, and the temperature for the onset of HCl evolution and the peak decomposition temperature (DTA) increase, i.e. 260°-280°C and 290°-325° C, respectively, compared with 240°-260°C and 260°-280°C for the unmodified homopolymer, in the absence of stabilizer. The grafting reaction may be carried out on suspension, emulsion, or bulk polymerized poly(vinyl chloride) with little or no change in the glass transition temperature. 

The relative initial ratio of acrylonitrile to butadiene and degree of conversion of nitrile to amidoxime are directly related to the resultant film s solubility parameter and glass transition temperature. Ideally, the concentration of amidoxime functional groups would be maximized while the coating s solubility parameter is matched to the vapor to be detected and the glass transition temperature is kept below room temperature. In practice, the conversion limitations are set by the reaction conditions of limited polymer solubility, reaction temperature and time. Three terpolymers of varying butadiene, acrylonitrile and amidoxime compositions were prepared as indicated in Table 1. 

The infrared spectra of the butadiene-acrylonitrile copolymer and butadiene-acrylonitrile-acrylamidoxime terpolymers are presented in Figure 2. The amidoxime specific bands appear at 3480 and 3380 cm-l (NH2 stretching) and at 1660 cm"l (C =N stretching) (1 2 ). The glass transition temperatures and solubility parameters of the corresponding polymers are also presented in Table 1. As the aerylamidoxime content increases from 3 to 7 to 45 mole percent, the... 

Composition, Solubility Parameter and Glass Transition Temperature of (Butadiene)x-(Acrylonitrile)y-(Acrylamidoxime)z... 

---