Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Glass, organic hard glasses

The sodium fusion and extraction, if performed strictly in accordance with the above directions, should be safe operations. In crowded laboratories, however, additional safety may be obtained by employing the follow ing modification. Suspend the hard-glass test-tube by the rim through a hole in a piece of stout copper sheet (Fig. 69). Place 1 -2 pellets of sodium in the tube, and heat gently until the sodium melts. Then drop the organic compound, in small quantities at a time, down — =. the tube, allowing the reaction to subside after each addition before the next is made. (If the compound is liquid, allow two or three small drops to fall at intervals from a fine dropping-tube directly on to the molten sodium.) Then heat the complete mixture as before until no further reaction occurs. [Pg.322]

Transmission electron microscopy (TEM) is a powerful and mature microstructural characterization technique. The principles and applications of TEM have been described in many books [16 20]. The image formation in TEM is similar to that in optical microscopy, but the resolution of TEM is far superior to that of an optical microscope due to the enormous differences in the wavelengths of the sources used in these two microscopes. Today, most TEMs can be routinely operated at a resolution better than 0.2 nm, which provides the desired microstructural information about ultrathin layers and their interfaces in OLEDs. Electron beams can be focused to nanometer size, so nanochemical analysis of materials can be performed [21]. These unique abilities to provide structural and chemical information down to atomic-nanometer dimensions make it an indispensable technique in OLED development. However, TEM specimens need to be very thin to make them transparent to electrons. This is one of the most formidable obstacles in using TEM in this field. Current versions of OLEDs are composed of hard glass substrates, soft organic materials, and metal layers. Conventional TEM sample preparation techniques are no longer suitable for these samples [22-24], Recently, these difficulties have been overcome by using the advanced dual beam (DB) microscopy technique, which will be discussed later. [Pg.618]

Carbon and Hydrogen by Combustion.—When an organic compound is heated in the presence of copper oxide or in a stream of pure oxygen gas, it is oxidized or burned. If the oxidation is complete, all of the carbon of the compound is converted into carbon dioxide and all of the hydrogen into water. The combustion is carried out in a long tube of hard glass, or of fused quartz, known as a combustion tube. [Pg.918]

If there is doubt as to whether the compound is organic, a sample of it can be heated in a hard glass tube with powdered copper oxide, and the evolved gas tested for carbon dioxide. If the substance is volatile it is necessary to place a mixture of it and copper oxide in the bottom of the tube and then add enough of the oxide to make a layer at least 5 cm. thick. The tube is carefully heated, beginning at the point farthest from the bottom of the tube. [Pg.39]

Glycol ethers and surfactants couple organic soils into the water phase and keep the soil suspended in the cleaner. Cleaner formulations can be classified as glass cleaners, hard surface cleaners, and industrial or heavy duty cleaners. Water is the... [Pg.78]

Recent applications of e-beam and HF-plasma SNMS have been published in the following areas aerosol particles [3.77], X-ray mirrors [3.78, 3.79], ceramics and hard coatings [3.80-3.84], glasses [3.85], interface reactions [3.86], ion implantations [3.87], molecular beam epitaxy (MBE) layers [3.88], multilayer systems [3.89], ohmic contacts [3.90], organic additives [3.91], perovskite-type and superconducting layers [3.92], steel [3.93, 3.94], surface deposition [3.95], sub-surface diffusion [3.96], sensors [3.97-3.99], soil [3.100], and thermal barrier coatings [3.101]. [Pg.131]

The OLED is composed of hard and soft layers so that the conventional cross-sectional TEM sample preparation techniques cannot be applied. Figure 10.3 is a first DB microscopy-prepared TEM image of an OLED in cross-sectional view [37], The glass substrate, ITO, organic layers, and A1 cathode are indicated in the image. The microstructure and interfaces of all these layers can be well studied now. The nanometer-sized spots in organic layers are indium-rich particles. We believe the combination of DB microscopy and TEM will greatly advance the OLED research and development in the near future. [Pg.621]


See other pages where Glass, organic hard glasses is mentioned: [Pg.235]    [Pg.321]    [Pg.2]    [Pg.173]    [Pg.96]    [Pg.470]    [Pg.920]    [Pg.151]    [Pg.11]    [Pg.373]    [Pg.671]    [Pg.278]    [Pg.209]    [Pg.368]    [Pg.395]    [Pg.226]    [Pg.108]    [Pg.189]    [Pg.178]    [Pg.259]    [Pg.146]    [Pg.470]    [Pg.526]    [Pg.527]    [Pg.139]    [Pg.18]    [Pg.14]    [Pg.424]    [Pg.154]    [Pg.169]    [Pg.126]    [Pg.554]    [Pg.6]    [Pg.139]    [Pg.46]    [Pg.50]    [Pg.97]    [Pg.102]    [Pg.436]    [Pg.189]    [Pg.128]    [Pg.301]    [Pg.238]    [Pg.311]   
See also in sourсe #XX -- [ Pg.6 , Pg.29 ]




SEARCH



Glasses hardnesses

Hard glass

Organic glasses

© 2024 chempedia.info