Flash points chemicals

Low toxicity solvents, heat transfer through water rather than oil, high flash point chemicals... 

Replacing the dangerous by the non-dangerous or less dangerous - for instance, replacing a low flash point chemical with either a non-flammable chemical or a chemical with a higher flash point (Chapter 7). 

The flash point of furfural is 143°F by Tag Closed Cup. Because of its chemical reactivity, furfural should be kept away from strong acids, alkaHes or strong oxidi2ing chemicals. When furfural is stored for long periods in contact with air, there is a gradual darkening of color, increase in acidity, and formation of a soluble polymer. 

Furan should be kept from heat and flame because of its low boiling point, low flash point, and high flammabiHty. Unstabilized furan slowly forms an unstable peroxide on exposure to air and, therefore, care should be taken when using furan. When distilling furan, remove peroxides first by chemical... 

Flash points and autoignition temperatures are given in Table 11. The vapor can travel along the ground to an ignition source. In the event of fire, foam, carbon dioxide, and dry chemical are preferred extinguishers. The lower and upper explosion limits are 1% and 7%. 

Fluid Chemical composition Temperature range, °C Min Max Viscosity, mPa-s(= cP) Vapor pressure, kPA Pour point, °C Flash point, °C Fire point, °C ait/ °C... 

Methyl-1-pentene [691-37-2] is alight, colorless, flammable fiquid its physical constants are also given in Table 1. It is an irritant and, in high concentrations, a narcotic. Like 1-butene, this chemical compound has a low flash point and represents a significant fire hazard when exposed to heat, flame, or oxidizing agents. 

Tables 16 and 17 Hst tke analytical test methods for different properties of interest. The Manufacturing Chemists Association, Inc. (MCA) has pubUshed the Chemical Safety Data Sheet SD 63, which describes in detail procedures for safe handling of use of toluene (46). The Interstate Commerce Commission classifies toluene as a flammable Hquid. Accordingly, it must be packaged in authorized containers, and shipping must comply with ICC regulations. Properties related to safe handling are autoignition temperature, 536°C explosive limits, 1.27—7.0 vol % in air and flash point 4.4°C, closed cup.

With minor exceptions the requirements for the physical and chemical properties of asphalt were essentially the same for the three national specifications and included penetration and ductiUty at 25 °C flash point % loss at 163 °C penetration of residue as a % of original solubiUty in carbon disulfide solubiUty in carbon tetrachloride specific gravity at 25°C and softening point. 

Procedures for shipping boric acid esters depend on the particular compound. Aryl borates produce phenols when in contact with water and are therefore subject to shipping regulations governing such materials and must carry a Corrosive Chemical label. Lower alkyl borates are flammable, flash points of methyl, ethyl, and butyl borates are 0, 32, and 94°C, respectively, and must be stored in approved areas. Other compounds are not hazardous, and may be shipped or stored in any convenient manner. Because borate esters are susceptible to hydrolysis, the more sensitive compounds should be stored and transferred in an inert atmosphere, such as nitrogen. 

Special additives are often included in a carrier formulation to provide specific properties such as foam control, stabiUty, and fiber lubrication during dyeing. Most important are the solvents used to solubilize the soHd carrier-active chemicals. These often contribute to the general carrier activity of the finished product. For example, chlorinated benzenes and aromatic esters are good solvents for biphenyls and phenylphenols. Flammable compounds (flash point below 60°C) should be avoided. 

Physical and chemical properties of the chemical, including boiling point, molecular weight, and flash point... 

Chemical compound Flam, limits, lower, % v/v Flam, hmits, upper, % v/v Autoignition temperature. Flash point, closed cup. Flash point, open cup. 

Small concentrations of volatile components in a liquid mixture may accumulate in the vapor space of a container over time and appreciably reduce the flash point relative to the reported closed-cup value. This may be the result of degassing, chemical reaction or other mechanism. An example is bitumen [162]. Similarly, if a tank truck is not cleaned between deliveries of gasoline and a high flash point liquid such as kerosene or diesel oil, the mixture might generate a flammable atmosphere both in the tmck tank and the receiving tank. Contamination at the thousand ppm level may create hazards (5-1.4.3 and 5-2.5.4). Solids containing upward of about 0.2 wt% flammable solvent need to be evaluated for flammable vapor formation in containers (6-1.3.2). 

The fuels consumed in the fire were treated wood, penta, and creosote (coal tars). Both are considered combustible liquids, with flash points above 160° F (CC). Vapor conditions within the headspaces of tanks can, however, reach explosive conditions, and the introduction of an ignition source resulted in spontaneous combustion. Under ideal conditions, creosote burns similar to crude oil, and in standard lab burn tests, has an average burn rate of 4 mm/min. There is no data on the burn rate of penta however, its vapors would have likely burned at much slower rates and a series of complex chemical transformations would have occurred. 

The substitution of one hydroxyl radical for a hydrogen atom in propane produces propyl alcohol, or propanol, which has several uses. Its molecular formula is C3H7OH. Propyl alcohol has a flash point of 77°F and, like all the alcohols, bums with a pale blue flame. More commonly known is the isomer of propyl alcohol, isopropyl alcohol. Since it is an isomer, it has the same molecular formula as propyl alcohol but a different structural formula. Isopropyl alcohol has a flash point of 53 F. Its ignition temperamre is 850°F, while propyl alcohol s ignition temperature is 700 F, another effect of the different stmcture. Isopropyl alcohol, or 2-propanol (its proper name) is used in the manufacture of many different chemicals, but is best known as rubbing alcohol. 

Fire Hazards - Flash Point (deg. F) 113 OC Flammable Limits in Air (%) Not pertinent Fire Extinguishing Agents Water, dry chemical, carbon dioxide Fire Extinguishing Agents Not To Be Used Not pertinent Special Hazards of Combustion Products Not pertinent Behavior in Fire May explode. Bums with accelerating intensity Ignition Temperature (deg. F) Explodes Electrical Hazard Data... 

---