Fires ignition sources

Fire ignition sources (e.g. electrical equipment special requirements) (Y/N) Fire spread (e.g. fire retardant cable coatings) (Y/N)... 

Fire can be represented by a simple equation Fire = Ignition Source -i- Fuel -i- Oxygen. Without any one of these three elements, a fire cannot start. Likewise, during a fire, if you take away any one of these three elements, you can successfully put out a fire. It is our company s intent to prevent these three elements from reacting to produce a fire. Here are the major, potential fire hazards specific to our workplace ... 

The autoignition temperature is the minimum temperature required for self-sustained combustion in the absence of an external ignition source. The value depends on specified test conditions. Tht flammable (explosive) limits specify the range of concentration of the vapor in air (in percent by volume) for which a flame can propagate. Below the lower flammable limit, the gas mixture is too lean to burn above the flammable limit, the mixture is too rich. Additional compounds can be found in National Fire Protection Association, National Fire Protection Handbook, 14th ed., 1991. 

Flash points and autoignition temperatures are given in Table 11. The vapor can travel along the ground to an ignition source. In the event of fire, foam, carbon dioxide, and dry chemical are preferred extinguishers. The lower and upper explosion limits are 1% and 7%. 

Flammability Acrolein is very flammable its flash point is <0° C, but a toxic vapor cloud will develop before a flammable one. The flammable limits in air are 2.8% and 31.0% lower and upper explosive limits, respectively by volume. Acrolein is only partly soluble in water and will cause a floating fire, so alcohol type foam should be used in firefighting. The vapors are heavier than air and can travel along the ground and flash back from an ignition source. 

Extreme caution must be taken to prevent the possibility of fire when using flammable removers. Extra care must be taken when stripping on location to secure the area of ignition sources. When used on lacquer finishes, the dissolved finish and remover combined are extremely flammable. Natural mbber, neoprene, or other gloves suitable for use with the remover formula must be worn. The effect of skin contact with the remover is limited because there is immediate irritation and discomfort. Canister respirators are available for most petroleum and oxygenate remover solvents. Symptoms of long-term overexposure should be compared to symptoms of the major ingredients in the formula. 

Hot Work. The objective of a hot work standard is to prevent fires, explosions, and other causes of injury which might result from workplace ignition sources such as welding (qv), cutting, grinding, and use of electrically powered tools. The OSHA standards have specific requirements (36,94) for fire prevention and protection and a permit system. 

The spark must always be produced by a spontaneous breakdown of the gas because an electronic firing circuit or a trigger electrode would either obviate the measurement of spark energy or grossly change the geometry of the ignition source (1,2,9). 

Ignition of flammable Provide safe separation distances release resulting in fire. Develop appropriate area electrical or explosion. classification Provide ignition source control Place ignition sources in positive pressure enclosure and buildings Provide adequate ventilation API RP500 BS 5345 BS 5958 NFPA-70 NFPA-77... 

Design to contain overpressure where practical Maintain ignition source control Maintain use of inert atmosphere Provide automatic isolation via quick closing valves of manifold duct system on detection of fire/flammable atmosphere or overpressure in duct system... 

Ignition of flammable atmosphere for open filters or solvent may be above flash point with air present when cleaning or unplugging closed filters. This may necessitate tight control of ignition sources to prevent a fire/explosion. 

Upper Flammable Limit (UFL) The highest concentration of a vapor or gas (the highest percentage of the substance in air) that will produce a flash of fire when an ignition source (heat, arc, or flame) is present. See also Lower Flammable Limit. At concentrations higher then the UFL, the mixture is too rich to burn. 

A logic model that graphically portrays the range of outcomes from the combinations of events and circumstances in an accident sequence. For example, a flammable vapor release may result in a fire, an explosion, or in no consequence depending on meteorological conditions, the degree of confinement, the presence of ignition sources, etc. These trees are often shown with the probability of each outcome at each branch of the pathway... 

Ignition source No. of fires % of all fires Loss 000 % of total cost of all fires... 

Certain materials which are generally considered to be stable at ordinary temperatures can inflame even in tlie absence of normal ignition sources. Such spontaneous combustion results from exotliermic autoxidation when the heat liberated exceeds that dissipated by the system. Materials prone to self-heating are listed in Table 6.7. In most cases, such fires involve relatively large, enclosed or thermally-insulated masses, and spontaneous combustion usually occurs after prolonged storage. 

Clearly mark the area with notices indicating an LPG storage area, flammable contents, prohibition of ignition sources and procedures to follow in case of fire. 

Total quantity LPC store Size of largest stack Minimum separation distance to boundary, building or fixed ignition sources from tbe nearest cylinder (where no fire wall provided) Minimum separation distance to boundary, building or fixed ignition source from fire wall (where provided) ... 

---