File names

Real Time X-Ray images are stored on CD ROM/XA. Compared to film the volume for a storage is reduced by a factor 50. Retrieving is easy since information of the location is given in the directory of the diskette. Normally the directory name is the shop order and the file name is the serial number of the part. The directory and file names can be customised. 

FilcForrnat describes whether this file is in text or dH.ASK for-m at. Th is is, by con ven tion, available in the file nam cs,. txi or fdhf, blit the. Atom fypeMass file name is strictly arbitrary and th e file IS in terpreted on th e basis of th e FilcFormat settin g. 

Enter Cartesian Coordinate Eile Name cbu2.xyz Enter Potential Parameter File Name mm3... 

Alternatively, the SCREEN.DAT file may be edited as an ASCII file using a text or line editor, and selected input parameters changed before rerunning the model. Since the original SCREEN.DAT file will be overwritten each time the model is run, it is advisable to save the modified inputs under a different file name. 

Regardless of whether or not a hardcopy is printed, the results of the session, including all input data and concentration estimates, are stored in a file called SCREEN.OUT. This file is opened by the model each time it is run. If a file named SCREEN.OUT already exists, then its contents will be overwritten or lost. 

File I Save and File Save Ai save stream data to a file, with Save As prompting you for a file name. 

Select 4 from this menu and POST (postprocessor) begins by requesting the data input file name (e.g., dg.pi - prepared by FTAPlus), the punch file name (e.g., dg.pch), the block file name (e g. dg.blk) and the name to be assigned to the new punch file (e.g., dgn.pch). Two outputs are produced FN.BLK and FNN.PCH. 

To do this go to FTAPSUIT (refer to j Section 6.4.2. Go to the FTAPSUIT main 3 menu and select 1 to go to FTAPlus to input the data. The first selection is the title, the second is the file name (use "pv" for this... 

Since dependency analysis is not needed, we can go on to the BUILD program. Go to FTAPSUIT and select 5 "Run Build." It asks you for the input file name including extender. Type "pv.pch," It asks you for name and extender of the input file for IMPORTANCE. Type, for examle, "pv.ii . It next asks for the input option. Type "5" for ba.sic event failure probabilities. This means that any failure rates must be multiplied by their mission times as shown in Table 7.4-1. (FTAPlus was written only for option 5 which uses probabilities and error factors. Other options will require hand editing of the pvn.ii file. The switch 1 is for failure rate and repair time, switch 2 is failure rate, 0 repair time, switch 3 is proportional hazard rate and 0 repair time, and switch 4 is mean time to failure and repair time.)... 

THE IMPORTANCE COMPUTER CODE DEVELOPED BY FTA A.S.SOri A rES INPUT FILE NAME pvn.ii TIME AND DATE OF RUN-- 1(1 il APR ] 1 ) chemical proce s tank niplure... 

IMPORTANCE must be run to find the probability of the fault tree, even if the importances are not of interest. Go to FTAPSUIT and type 7. It asks for the input file name type "pvn.ii." The output is pvn.io which after editing (for format) is presented as Figure 7.4-5, It has calculated the Fussel-Vesely importances because of the "FV" in Figure 7.4-3. The probability of the top event is 4.5538E-3 whereas 4.56E-3 was calculated by the previous hand calculation. It says that the cutset con ting of the relief valve-switch-timer is the most important. 

A Monte Carlo calculation of the tree results from running MONTE by selecting "8" from the FTAPSUIT main menu. It asks for a file name (and extender) type "pvn.mi." It takes the most time to run of all of the programs its output is "pvn.mo" as shown in Figure 7.4-6. 

PROGRAM name (input file name(s), output file narne(s)) ... 

Figure 5.4. The presentation of the values contained in a data file. A program and file names B size of file C instructions on how to proceed D currently active rounding option E. abscissa vector F ordinate vector.

The supplimentary information comprises the file name and the vector number(s), and important results, but not the data table as such. 

The first step is to determine the level of the baseline before and after the part of the chromatogram which characterizes the specimen, apply a straight-line correction so that the overall baseline is effectively zero, and cut out from the entire chromatogram that part which pertains to the specimen. The "cut" chromatogram may be written to a file which is named automatically by using CUT as an extension of the file name. 

CALL Formula lookup (Formula file name. Density, Solids, Pigment solids. Cost,... 

CALL Formula file read (Formula file name. Code, Weight, N rows. Error code)... 

CALL Formula lookup (Pass formula file name,Row density(Row),... 

When a simulation is completed, the data gathered during the simulation are collected into a report. This report, as a text file, will be found in the CAOutput directory with a file name indicating the Example, the Setting file, and the time of the simulation. For instance, the file name for a report of a simulation which ranExample3-l with Setting file abc.set on May lOat 13 hour and 45 minutes would be... 

Demonstrate that the printed, hand-signed copy has sufficient information to link the report to a unique electronic record (date, time printed, name of person printing report, file name, date/... 

The foundation of any efficient computer-assisted data analysis system is the creation and use of data standards. Data standards consist of standard data file names for each predefined file, standard data elements in each data file, standardized names for each data element, and standard definitions for each data element. 

Each simulation example is identified by a file name and title, and each comprises the qualitative physical description with drawing, the model equation development, the nomenclature, the ISIM program, suggested exercises, sample graphical results and literature references. The diskette in the pocket at the back of the book contains the programs and the ISIM software. 

---