Exposure filter

Of all the design characteristics of cigarettes, filter ventilation may be the most important in determining machine-smoked yields (Djordjevic et al. 1995), as well as the most important determinant of the differences in machine-smoked yields and human smoking behavior and smoke exposure. Filter ventilation dilutes mainstream... 

Each element of the matrix established in Step 3 is multiplied with the appropriate exposure filter and one of the two effects filters in Step 4. 

To verify the modelling of the data eolleetion process, calculations of SAT 4, in the entrance window of the XRII was compared to measurements of RNR p oj in stored data as function of tube potential. The images object was a steel cylinder 5-mm) with a glass rod 1-mm) as defect. X-ray spectra were filtered with 0.6-mm copper. Tube current and exposure time were varied so that the signal beside the object. So, was kept constant for all tube potentials. Figure 8 shows measured and simulated SNR oproj, where both point out 100 kV as the tube potential that gives a maximum. Due to overestimation of the noise in calculations the maximum in the simulated values are normalised to the maximum in the measured values. Once the model was verified it was used to calculate optimal choice of filter materials and tube potentials, see figure 9. 

The IP s were used in combination with appropriate Pb-filters (see 121). For wall thickness inspection we used standard medical IP s (AGFA MDIO), which exhibited an inherent unsharpness of ca. 310 pm. This should be compared with the inherent unsharpness of the film for an Ir-192 exposure which amounts 230 pm 111. For corrosion assessment we used IP prototypes with an inherent unsharpness < 230 pm. 

In fig. 2 an ideal profile across a pipe is simulated. The unsharpness of the exposure rounds the edges. To detect these edges normally a differentiation is used. Edges are extrema in the second derivative. But a twofold numerical differentiation reduces the signal to noise ratio (SNR) of experimental data considerably. To avoid this a special filter procedure is used as known from Computerised Tomography (CT) /4/. This filter based on Fast Fourier transforms (1 dimensional FFT s) calculates a function like a second derivative based on the first derivative of the profile P (r) ... 

Anthracene and maleic anhydride. In a 50 ml. round-bottomed flask fitted with a reflux condenser, place 2 0 g. of pure anthracene, I 1 g. of maleic anhydride (Section 111,93) and 25 ml. of dry xylene. Boil the mixture under reflux for 20 minutes with frequent shaking during the first 10 minutes. Allow to cool somewhat, add 0 5 g. of decolourising carbon and boil for a further 5 minutes. Filter the hot solution through a small, preheated Buchner funnel. Collect the solid which separates upon coohng by suction filtration, and dry it in a vacuum desiccator containing paraffin wax shavings (to absorb traces of xylene). The yield of adduct (colourless crystals), m.p. 262-263° (decomp.), is 2-2 g. Place the product (9 10-dihydroanthracene-9 10-cndo-ap-succinic anhydride) in a weU-stoppered tube, since exposure to air tends to cause hydration of the anhydride portion of the molecule. 

Three approaches have been identified that reduce susceptibility of CA resists to airborne contamination. In the first, process engineering changes such as the addition of special activated carbon filters to the environmental chambers surrounding the exposure tools (76,79), overcoating the resist with a soluble protective film to isolate the resist from the environment (77,80,81), or modifications of the process flow to minimize the time interval between exposure and post-exposure bake have been shown to improve CA resist processibibty. 

A second degradation process is oxidation, often photo-induced especially by exposure to light not filtered for uv. The radicals resulting from this reaction promote depolymerization of the cellulose, as well as yellowing and fa ding of paper and media. Aging causes paper to become more crystalline and fragile, and this can be exacerbated particularly if the paper is subjected to poor conditions. 

Fig. 1. Southern blot analysis of DNA showing (a) step 1, an agarose gel containing separated restriction fragments of DNA, denoted by (—), which is immersed in NaOH to denature the double-stranded stmcture of DNA, and then transferred by capillary flow to a nitrocellulose filter. In step 2, the bound DNA is allowed to hybridize to a labeled nucleic acid probe, and the unbound probe is washed off In step 3, the filter is placed into contact with x-ray film resulting in (b) bands of exposure on the film which are detected after development and correspond to regions where the restriction fragment is...

Many filters in chemical process units are either changed very rarely or are back-flushed automatically so there is hardly any exposure. Some filters, however, require frequent manual changing or cleaning and significant exposure may occur unless operators foUow the proper procedure. The filter container should be drained of any toxic material and then flushed and purged as needed so that when it is opened there is only minimal exposure. Zero exposure is difficult to achieve in situations where a disposable paper filter cartridge may retain and slowly release a material that cannot be removed by multiple flushes and purges. 

Air cleaning systems are often used to remove dust or vapors from plant or process exhaust streams. Dust collecting systems such as filters or electrostatic precipitators that handle heavy loads of dust are usually designed to be self-cleaning, but it is stiU. necessary to enter the air cleaner periodically for inspection or repair. Dust deposits inside the equipment are likely to be stirred up and inhaled by unprotected workers. Baghouses are particularly likely to cause exposure because large amounts of dust may be retained in the cloth and released when the bags are handled. 

Techniques for handling sodium in commercial-scale appHcations have improved (5,23,98,101,102). Contamination by sodium oxide is kept at a minimum by completely welded constmction and inert gas-pressured transfers. Residual oxide is removed by cold traps or micrometallic filters. Special mechanical pumps or leak-free electromagnetic pumps and meters work well with clean Hquid sodium. Corrosion of stainless or carbon steel equipment is minimi2ed by keeping the oxide content low. The 8-h TWA PEL and ceiling TLV for sodium or sodium oxide or hydroxide smoke exposure is 2 mg/m. There is no defined AID for pure sodium, as even the smallest quantity ingested could potentially cause fatal injury. 

---