Embedding process

In order to test this, Kelly et al. (1997) point out that we need a set of biological markers thought to be sensitive to long-term systematic differences in socioeconomic status and living conditions, and these markers must be feasible to measure in large population surveys, so their role in the biological embedding process can be evaluated on a population-based, person-specific basis. 

Using the secret key, one reconstructs the binary string M, and the graph G with all the extra edges added as in the embedding process. 

Sectioning material for immunocytochemistry with glass and diamond knives is identical to the process used for conventional EM. One difficulty frequently encountered is that unosmicated tissue embedded in plastic is sufficiently cleared by the solvent and embedding process as to be almost invisible. This makes orientation of the tissue in the trimming of the blocks difficult and increases the chances of mistakes of cutting too much. A small amount of Sudan Black dye can be added to... 

The design, development, and system build phases need to deliver computer systems and services in a manner that facilitates effective and efficient system validation, operation, maintenance, modification, and upgrade. This applies to both stand-alone and embedded process control computer systems (see Sec. VI). 

Immunoreactivity diminished or destroyed during embedding process. Use a paraffin wax with a melting temperature - 55-58 °C. Wax used for embedding should not exceed 60 °C. 29-33... 

Tsujimura M. Embedded process monitor and control in CMP tool. SEMI Technology Symposium 2000. p 2-51-56. 

Bowden and Tabor ° have described two phenomena which may have important influences on this embedment process. They showed that when a copper slider passed over a harder steel surface, fragments of copper adhered to the steel. In addition the steel surface was ruptured and copper penetrated the fissures created, in view of the very high hardness of the crystal edges in molybdenum disulphide, such a rupturing and penetration process seems even more likely to take place than in the case of copper on steel. 

The embedding process is reinforced by appraisal and reward systems. Since 1997, contributing to sustainable development has counted in the remuneration of Shell s most senior executives and in the appraisal of Group Business. Similar reward schemes are adopted across Shell s operating companies, providing very powerful incentives to operate in a sustainable way. 

As a hypothetical case, consider the situation when all the watermarking information are known for the watermark embedding process. Then for each lc-region, some cut-off c is selected in step 2c of Algorithm 1. It is the best to take fc = c for that lc-region. In that case, the energy difference created in that lc-region will be vanished. 

Fig. 1 depicts a general blind symmetric watermarking scheme. The term blind indicates that the host signal x is not known at the watermark detector. The watermark information b is embedded into the host signal x dependent on a private key. All modifications introdnced by the embedding process are denoted by the watermark signal w, so that the public signal s can be expressed as s = x -I- w. The distortion introduced... 

Typical configuration for an ESD system is shown in Fig. VIII/4.6-1. All field inputs from process variables and outputs to various actuators MCC shall be connected to the ESD system with the help of an I/O bus. Depending on applicability there could be redundancies in various systems and the communication bus, as shown in Fig. VIII/ 4.6-1. Redundancies are shown with shadows. In the case of other systems where there are multiple systems, these are also shown with the help of shadows. Some systems (say an alarm system) may have an RS 485/422 link. In this configuration an attempt is made to highlight that the system is an independent system but can have an interface with other systems as well. At the top layer, Ethernet has been considered for HMIs, data server (if any), SOE, and other open systems on the same IEEE 802.3 Ethernet. There could be object linking and embedding process control (OPC) clients and these could be serviced by an ESD logic server, which will have dual or TMR redundancy built in. 

Typical emergency shutdown (ESD) configuration with interface. ESD, emergency shutdown FGS, fire and gas system HMIs, human-machine interfeces I/O, input/output MCC, motor control center OPC, object linking and embedding process control SOE, sequence of events. 

Key findings of success of the networked platforms are acquisition of key players of the sector, tailored and embedded processes and expansion of additional services like collaborative planning. 

---