Electromagnet visible

There are more issues and complexity to be considered if various micro-electromechanical (MEMS)-type devices are included in the macroelectronics tool kit. As described previously, the materials and devices required for TFTs and circuits can provide adequate electromagnetic (visible and RF) sensitivity for many image-type applications. These materials may also provide satisfactory performance in pressure and strain sensors. Nanotube/nanowire-based devices look promising for various chem-bio sensors.85 However, there is little that is known about the ability to integrate printed microfluidic devices (and other such devices with moving parts) into a roll-to-roll-type process. 

In the electromagnetic spectrum, the ultra violet region is between that of X-rays and visible light. This corresponds to the energies hv ot one hundred to a few tens of electron-volts (wavelengths from 180 to 400 nm). 

Electromagnetic radiation of which visible light is but one example has the properties of both particles and waves The particles are called photons, and each possesses an amount of energy referred to as a quantum In 1900 the German physicist Max Planck proposed that the energy of a photon (E) is directly proportional to its frequency (v)... 

Electromagnetic radiation (Section 13 1) Vanous forms of ra diation propagated at the speed of light Electromagnetic radiation includes (among others) visible light infrared ul traviolet and microwave radiation and radio waves cos mic rays and X rays... 

Colorimetry, in which a sample absorbs visible light, is one example of a spectroscopic method of analysis. At the end of the nineteenth century, spectroscopy was limited to the absorption, emission, and scattering of visible, ultraviolet, and infrared electromagnetic radiation. During the twentieth century, spectroscopy has been extended to include other forms of electromagnetic radiation (photon spectroscopy), such as X-rays, microwaves, and radio waves, as well as energetic particles (particle spectroscopy), such as electrons and ions. ... 

The focus of this chapter is photon spectroscopy, using ultraviolet, visible, and infrared radiation. Because these techniques use a common set of optical devices for dispersing and focusing the radiation, they often are identified as optical spectroscopies. For convenience we will usually use the simpler term spectroscopy in place of photon spectroscopy or optical spectroscopy however, it should be understood that we are considering only a limited part of a much broader area of analytical methods. Before we examine specific spectroscopic methods, however, we first review the properties of electromagnetic radiation. 

The electromagnetic spectrum showing the colors of the visible spectrum. 

In absorption spectroscopy a beam of electromagnetic radiation passes through a sample. Much of the radiation is transmitted without a loss in intensity. At selected frequencies, however, the radiation s intensity is attenuated. This process of attenuation is called absorption. Two general requirements must be met if an analyte is to absorb electromagnetic radiation. The first requirement is that there must be a mechanism by which the radiation s electric field or magnetic field interacts with the analyte. For ultraviolet and visible radiation, this interaction involves the electronic energy of valence electrons. A chemical bond s vibrational energy is altered by the absorbance of infrared radiation. A more detailed treatment of this interaction, and its importance in deter-... 

The determination of an analyte s concentration based on its absorption of ultraviolet or visible radiation is one of the most frequently encountered quantitative analytical methods. One reason for its popularity is that many organic and inorganic compounds have strong absorption bands in the UV/Vis region of the electromagnetic spectrum. In addition, analytes that do not absorb UV/Vis radiation, or that absorb such radiation only weakly, frequently can be chemically coupled to a species that does. For example, nonabsorbing solutions of Pb + can be reacted with dithizone to form the red Pb-dithizonate complex. An additional advantage to UV/Vis absorption is that in most cases it is relatively easy to adjust experimental and instrumental conditions so that Beer s law is obeyed. 

As discussed earlier in Section lOC.l, ultraviolet, visible and infrared absorption bands result from the absorption of electromagnetic radiation by specific valence electrons or bonds. The energy at which the absorption occurs, as well as the intensity of the absorption, is determined by the chemical environment of the absorbing moiety. Eor example, benzene has several ultraviolet absorption bands due to 7t —> 71 transitions. The position and intensity of two of these bands, 203.5 nm (8 = 7400) and 254 nm (8 = 204), are very sensitive to substitution. Eor benzoic acid, in which a carboxylic acid group replaces one of the aromatic hydrogens, the... 

The so-called peak power delivered by a pulsed laser is often far greater than that for a continuous one. Whereas many substances absorb radiation in the ultraviolet and infrared regions of the electromagnetic spectrum, relatively few substances are colored. Therefore, a laser that emits only visible light will not be as generally useful as one that emits in the ultraviolet or infrared ends of the spectrum. Further, witli a visible-band laser, colored substances absorb more or less energy depending on the color. Thus two identical polymer samples, one dyed red and one blue, would desorb and ionize with very different efficiencies. 

A dye molecule has one or more absorption bands in the visible region of the electromagnetic spectrum (approximately 350-700 nm). After absorbing photons, the electronically excited molecules transfer to a more stable (triplet) state, which eventually emits photons (fluoresces) at a longer wavelength (composing three-level system.) The delay allows an inverted population to build up. Sometimes there are more than three levels. For example, the europium complex (Figure 18.15) has a four-level system. 

The scattering of visible light by polymer solutions is our primary interest in this chapter. However, since is a function of the ratio R/X, as we saw in the last section, the phenomena we discuss are applicable to the entire range of the electromagnetic spectrum. Accordingly, a general review of the properties of this radiation and its interactions with matter is worthwhile before a specific consideration of scattering. 

A modem use of uranine is in the manufacture of fluorescent laminates, eg, sheets, glass, and plastic films, that are transparent to electromagnetic waves and visible light rays (45). Such material might be used in windows, viewing partitions, and optical lenses. 

Most CCDs are specifically designed for video camera apphcations, which detect photons in the visible portion of the electromagnetic spectra. 

Radiation Resistance. Polysulfones exhibit resistance to many electromagnetic frequencies of practical significance, including microwave, visible, and infrared. Especially notable is the excellent resistance to microwave radiation, which has contributed to the excellent fit of polysulfones in cookware appHcations. Polysulfone also shows good resistance to x-rays, electron beam (24), and gamma (25,26) radiation under many practical appHcation conditions. 

---