Diisocyanate matrix

Maleamic acid, cyclization of, 293 Maleic anhydride, 59 Maleimido azine, 307 Manganese diacetate catalysts, 71 Mark-Houwink-Sakurada equation, 57 Material safety data sheets (MSDSs), 246 Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOFMS), 385, 388 McGrath, J. E., 327 MDI isomers, 210 MDIs. See Methylene diphenyl diisocyanates (MDIs)... 

Polymer Matrix Effects. In order to approximate the environment experienced by the arylcarbamate moieties in coatings based on aromatic diisocyanates, we chose to study the photochemistry of alkyl N-arylcarbamates in polymethacrylate (PMMA) and polypropyl-methacrylate (PPMA) films. First, however, 2a and 3a were irradiated in ethyl propionate (a model solvent for PMMA and PPMA) to determine the effect of the solvent polarity (dielectric) on the photolysis of the carbamates. Upon excitation at 280 nm, where the solvent absorbance was negligible, is 0.006 for 2a and 0j) is 0.005 for 3a. These values are significantly smaller... 

Composite rocket propellants are two-phase mixtures comprising a crystalline oxidizer in a polymeric fuel/binder matrix. The oxidizer is a finely-dispersed powder of ammonium perchlorate which is suspended in a fuel. The fuel is a plasticized polymeric material which may have rubbery properties (i.e. hydroxy-terminated polybutadiene crosslinked with a diisocyanate) or plastic properties (i.e. polycaprolactone). Composite rocket propellants can be either extruded or cast depending on the type of fuel employed. For composite propellants which are plastic in nature, the technique of extrusion is employed, whereas for composite propellants which are rubbery, cast or extruded techniques are used. 

Reaction-induced phase separation is certainly also the reason for which an inhomogeneous structure is observed for photocured polyurethane acrylate networks based on polypropylene oxide (Barbeau et al., 1999). TEM analysis demonstrates the presence of inhomogeneities on the length scale of 10-200 nm, mostly constituted by clusters of small hard units (the diacrylated diisocyanate) connected by polyacrylate chains. In addition, a suborganization of the reacted diisocyanate hard segments inside the polyurethane acrylate matrix is revealed by SAXS measurements. Post-reaction increases the crosslink density inside the hard domains. The bimodal shape of the dynamic mechanical relaxation spectra corroborates the presence of a two-phase structure. 

The design of the anchors totally depends on the proposed mechanism of SMA-matrix material incorporation. In this study, 4,4 -methylene diphenyl diisocyanate (MDI) is applied as the localizing anchor that physically bonds to the PEU matrix material by mimicking the physical crosslink between PEU hard blocks. Finally, the ABCBA -type SMA, named MPEO , is constructed as shown in Fig. 1, in which A represents bio-functional endgroups, B represents the PEG spacer, and C represents the MDI anchor that also plays the role of coupling groups for A-B moieties on both sides [76,77]. 

Composite rocket propeiiants. This type of propellant contains two-phase mixtures with a aystalhne oxidizer in a polymeric fuel or binder matrix. The finely dispersed powder of ammonium perchlorate suspended in a fuel is the oxidizer. The fuel is a plasticized polymeric material such as hydroxy-terminated polybutadiene cross-linked with a diisocyanate (rubber ts e) or carboxy-terminated polybutadiene (plastic type) [4]. 

In hard tissue replacement, polyurethane filled with hydroxyapatite is used. The composite must have high strength and stiffness and excellent creep and fatigue resistance. The material in the study met these requirements when hydroxyapatite was pretreated with hexamethylene diisocyanate. The treatment improved the adhesion between the matrix and the filler. ... 

Lee and Wang [80] investigated the effects of lysine-based diisocyanate (LDI) as a coupling agent on the properties of biocomposites from PLA, poly (butylene succinate) (PBS) and bamboo fiber (BF). They observed that the tensile properties, water resistance, and interfacial adhesion of both PLA/BF and PBS/BF composites were improved by the addition of LDI, but thermal flow [81] was hindered due to cross-linking between polymer matrix and BF. Enzymatic biodegradability of... 

U.S. Pat. No. 4,376,144 [60] discloses a thermoplastic composite in which cellulose hber (hardwood pulp, from 1 to 40% by weight) is attached to the PVC matrix with an isocyanate bonding agent (a cyclic trimer of toluene diisocyanate). 

---