Dielectric constant properties

Liquid solubilizers act by reducing the dielectric constant properties of the solvent system, thereby reducing the electrical conductance capabilities of the solvent and increasing the solubility of hydrophobic or non-polar drugs. Lanoxin, Valium, and Nembutal are examples of commercially available sterile solutions containing cosolvent solubilizers. A popular combination consists of 40% propylene glycol and 10 /o ethanol in water. 

Similar results have been observed for polyester composites reinforced with different raw banana fibers [11]. Figure 15.12 shows the dielectric constant properties... 

Strong electrolytes are dissociated into ions that are also paired to some extent when tlie charges are high or the dielectric constant of the medium is low. We discuss their properties assuming that the ionized gas or solution is electrically neutral, i.e. 

Colloidal particles can be seen as large, model atoms . In what follows we assume that particles with a typical radius <3 = lOO nm are studied, about lO times as large as atoms. Usually, the solvent is considered to be a homogeneous medium, characterized by bulk properties such as the density p and dielectric constant t. A full statistical mechanical description of the system would involve all colloid and solvent degrees of freedom, which tend to be intractable. Instead, the potential of mean force, V, is used, in which the interactions between colloidal particles are averaged over... 

The dipole moments of the hydrogen halides decrease with increasing atomic number of the hydrogen, the largest difference occurring between HF and HCl, and association of molecules is not an important factor in the properties of FICl, HBr and HI. This change in dipole moment is reflected in the diminishing permittivity (dielectric constant) values from HF to HI. 

The same idea was actually exploited by Neumann in several papers on dielectric properties [52, 69, 70]. Using a tin-foil reaction field the relation between the (frequency-dependent) relative dielectric constant e(tj) and the autocorrelation function of the total dipole moment M t] becomes particularly simple ... 

The dielectric constant is concerned with the electrical properties of a material. The dielectric constant for a solid is a 3 x 3 matrix with different components according to the Cartesian axes. These elements are given by ... 

The final class of methods that we shall consider for calculating the electrostatic compone of the solvation free energy are based upon the Poisson or the Poisson-Boltzmann equatior Ihese methods have been particularly useful for investigating the electrostatic properties biological macromolecules such as proteins and DNA. The solute is treated as a body of co stant low dielectric (usually between 2 and 4), and the solvent is modelled as a continuum high dielectric. The Poisson equation relates the variation in the potential (f> within a mediu of uniform dielectric constant e to the charge density p ... 

Solvents exert their influence on organic reactions through a complicated mixture of all possible types of noncovalent interactions. Chemists have tried to unravel this entanglement and, ideally, want to assess the relative importance of all interactions separately. In a typical approach, a property of a reaction (e.g. its rate or selectivity) is measured in a laige number of different solvents. All these solvents have unique characteristics, quantified by their physical properties (i.e. refractive index, dielectric constant) or empirical parameters (e.g. ET(30)-value, AN). Linear correlations between a reaction property and one or more of these solvent properties (Linear Free Energy Relationships - LFER) reveal which noncovalent interactions are of major importance. The major drawback of this approach lies in the fact that the solvent parameters are often not independent. Alternatively, theoretical models and computer simulations can provide valuable information. Both methods have been applied successfully in studies of the solvent effects on Diels-Alder reactions. 

The dielectric constant is a property of a bulk material, not an individual molecule. It arises from the polarity of molecules (static dipole moment), and the polarizability and orientation of molecules in the bulk medium. Often, it is the relative permitivity 8, that is computed rather than the dielectric constant k, which is the constant of proportionality between the vacuum permitivity so and the relative permitivity. 

This copolymer has useful properties from cryogenic temperatures to 180°C. Its dielectric constant is low and stable over a broad temperature and frequency range. 

Revised material in Section 5 includes an extensive tabulation of binary and ternary azeotropes comprising approximately 850 entries. Over 975 compounds have values listed for viscosity, dielectric constant, dipole moment, and surface tension. Whenever possible, data for viscosity and dielectric constant are provided at two temperatures to permit interpolation for intermediate temperatures and also to permit limited extrapolation of the data. The dipole moments are often listed for different physical states. Values for surface tension can be calculated over a range of temperatures from two constants that can be fitted into a linear equation. Also extensively revised and expanded are the properties of combustible mixtures in air. A table of triple points has been added. 

Equations (10.17) and (10.18) show that both the relative dielectric constant and the refractive index of a substance are measurable properties of matter that quantify the interaction between matter and electric fields of whatever origin. The polarizability is the molecular parameter which is pertinent to this interaction. We shall see in the next section that a also plays an important role in the theory of light scattering. The following example illustrates the use of Eq. (10.17) to evaluate a and considers one aspect of the applicability of this quantity to light scattering. 

Electrica.1 Properties. The bulk electrical properties of the parylenes make them excellent candidates for use in electronic constmction. The dielectric constants and dielectric losses are low and unaffected by absorption of atmospheric water. The dielectric strength is quoted for specimens of 25 p.m thickness because substantially thicker specimens cannot be prepared by VDP. If the value appears to be high in comparison with other materials, however, it should be noted that the usual thickness for such a measurement is 3.18 mm. Dielectric strength declines with the square root of increasing... 

Electrical properties of acetal resin are collected in Table 3. The dielectric constant is constant over the temperature range of most interest (—40 to 50°C). Table 3. Electrical Properties of Acetal Resins... 

Electrical Resistance—Conductivity. Most fillers are composed of nonconducting substances that should, therefore, provide electrical resistance properties comparable to the plastics in which they are used. However, some fillers contain adsorbed water or other conductive species that can gready reduce their electrical resistance. Standard tests for electrical resistance of filled plastics include dielectric strength, dielectric constant, arc resistance, and d-c resistance. 

Electrical Properties. The low polarizabiHty of perfluorinated Hquids makes them exceUent insulators. Theh dielectric strengths are about 40 kV (ASTM D877) dissipation factors are about 0.0001 at 1 MH2 dielectric constants are about 1.8 volume resistivities are about 1 x 10 ohm-cm (ASTM D257) (17). 

In air, PTFE has a damage threshold of 200—700 Gy (2 x 10 — 7 x 10 rad) and retains 50% of initial tensile strength after a dose of 10" Gy (1 Mrad), 40% of initial tensile strength after a dose of 10 Gy (10 lad), and ultimate elongation of 100% or more for doses up to 2—5 kGy (2 X 10 — 5 X 10 rad). During irradiation, resistivity decreases, whereas the dielectric constant and the dissipation factor increase. After irradiation, these properties tend to return to their preexposure values. Dielectric properties at high frequency are less sensitive to radiation than are properties at low frequency. Radiation has veryHtde effect on dielectric strength (86). 

Electrical Properties. Polytetrafluoroethylene is an excellent electrical insulator because of its mechanical strength and chemical and thermal stabihty as well as excellent electrical properties (Table 6). It does not absorb water and volume resistivity remains unchanged even after prolonged soaking. The dielectric constant remains constant at 2.1 for a temperature range of —40 to 250°C and a frequency range of 5 Hz to 10 GHz. 

---