Detector, atomic spectrometer sensitivity

As noted earlier, USNs have been employed for sample insertion into atomic spectrometers suoh as flame atomio absorption spectrometry (FAAS) [9,10], electrothermal atomic absorption speotrometry (ETAAS) [11], atomic fluorescence spectrometry (AFS) [12,13], induotively ooupled plasma-atomic emission spectrometry (ICP-AES) [14,15], inductively coupled plasma-mass spectrometry (ICP-MS) [16,17] and microwave induced plasma-atomic emission spectrometry (MIP-AES) [18,19]. Most of the applications of ultrasonic nebulization (USNn) involve plasma-based detectors, the high sensitivity, selectivity, precision, resolution and throughput have fostered their implementation in routine laboratories despite their high cost [4]. 

The association of a spectrometer with a liquid chromatograph is usually to aid in structure elucidation or the confirmation of substance identity. The association of an atomic absorption spectrometer with the liquid chromatograph, however, is usually to detect specific metal and semi-metallic compounds at high sensitivity. The AAS is highly element-specific, more so than the electrochemical detector however, a flame atomic absorption spectrometer is not as sensitive. If an atomic emission spectrometer or an atomic fluorescence spectrometer is employed, then multi-element detection is possible as already discussed. Such devices, used as a LC detector, are normally very expensive. It follows that most LC/AAS combinations involve the use of a flame atomic absorption spectrometer or an atomic spectrometer fitted with a graphite furnace. In addition in most applications, the spectrometer is set to monitor one element only, throughout the total chromatographic separation. 

There have been a number of reviews in the literature on the identification of metal species by LC/AAS (40-42) but to successfully utilize the combination, both the LC and the spectrometer system have to be optimized and this has also been the subject of a number of publications (43-45). It has been claimed (44) that the poor sensitivity obtained from the LC/AAS system relative, to that obtained from the atomic spectrometer alone, was due to the dispersion that takes place in the column. Although substantially true, this misunderstanding arises from the fact that the spectroseopist views the chromatograph as just another sampling device and not as a separation system. The point of interfacing a liquid chromatograph with an atomic spectrometer is to achieve a separation before detection and consequently, the important dispersion characteristics are not those that occur in the column but those that occur in the interfaces between the detector and the spectrometer and in the spectrometer itself. 

The simplest analytical method is direct measurement of arsenic in volatile methylated arsenicals by atomic absorption [ 11 ]. A slightly more complicated system, but one that permits differentiation of the various forms of arsenic, uses reduction of the arsenic compounds to their respective arsines by treatment with sodium borohydride. The arsines are collected in a cold trap (liquid nitrogen), then vaporised separately by slow warming, and the arsenic is measured by monitoring the intensity of an arsenic spectral line, as produced by a direct current electrical discharge [1,12,13]. Essentially the same method was proposed by Talmi and Bostick [10] except that they collected the arsines in cold toluene (-5 °C), separated them on a gas chromatography column, and used a mass spectrometer as the detector. Their method had a sensitivity of 0.25 xg/l for water samples. 

Mass spectrometry is a sensitive analytical technique which is able to quantify known analytes and to identify unknown molecules at the picomoles or femto-moles level. A fundamental requirement is that atoms or molecules are ionized and analyzed as gas phase ions which are characterized by their mass (m) and charge (z). A mass spectrometer is an instrument which measures precisely the abundance of molecules which have been converted to ions. In a mass spectrum m/z is used as the dimensionless quantity that is an independent variable. There is still some ambiguity how the x-axis of the mass spectrum should be defined. Mass to charge ratio should not lo longer be used because the quantity measured is not the quotient of the ion s mass to its electric charge. Also, the use of the Thomson unit (Th) is considered obsolete [15, 16]. Typically, a mass spectrometer is formed by the following components (i) a sample introduction device (direct probe inlet, liquid interface), (ii) a source to produce ions, (iii) one or several mass analyzers, (iv) a detector to measure the abundance of ions, (v) a computerized system for data treatment (Fig. 1.1). 

The atom-probe field ion microscope is a device which combines an FIM, a probe-hole, and a mass spectrometer of single ion detection sensitivity. With this device, not only can the atomic structure of a surface be imaged with the same atomic resolution as with an FIM, but the chemical species of surface atoms of one s choice, chosen from the field ion image and the probe-hole, can also be identified one by one by mass spectrometry. In principle, any type of mass analyzer can be used as long as the overall detection efficiency of the mass analyzer, which includes the detection efficiency of the ion detector used and the transmission coefficient of the system, has to be close to unity. 

---