Degree vulcanization

There are many ways to measure these properties and some of them are proprietary. However, most laboratory tests are standardized by American Standard Testing Methods (ASTM). Many of them are interactive to various degrees. The rate and state of vulcanization is especially important to consider for components of heavier and thicker tines. The heat used to vulcanize the tine in a mold under pressure requites time to penetrate from both sides of the giant tine to the innermost portions. Securing a balanced state of cure, ie, the maximizing of physical properties in all the components, results in the innermost components having a faster rate of cure. The peripheral compounds should have a cure system which holds its physical properties well when overcured. 

When the temperamre is lowered, rubbers become stiff and brittle. All rubbers eventually stiffen to a rigid, amorphous glass at the glass transition temperature (Tg). This temperature also indicates the low-temperature service limit of the rubber. Tg values are dependent on the structure, degree of cross-linking (vulcanization) and isomeric composition of the rubber. 

Vulcanization changes the physical properties of rubbers. It increases viscosity, hardness, modulus, tensile strength, abrasion resistance, and decreases elongation at break, compression set and solubility in solvents. All those changes, except tensile strength, are proportional to the degree of cross-linking (number of crosslinks) in the rubber network. On the other hand, rubbers differ in their ease of vulcanization. Since cross-links form next to carbon-carbon double bonds. 

The oldest technology involved in the elastomer blending and vulcanization process is essentially a temperature controlled two roll mill as well as internal mixers followed by an optimum degree of crosslinking in autoclave molds (compression, injection, etc.) in a batch process or in a continuous process such as continuously heated tube or radiated tubes. A few examples of laboratory scale preparation of special purpose elastomeric blends is cited here. 

Improvement in the solvent and oil resistance of rubbers can be achieved via grafting of acrylonitrile onto rubber [140-142] and rubber blends [143]. The careful control of the degree of grafting allows vulcanized rubber with high-mechanical properties compared with ungrafted vulcanized rubber to be obtained. Also, acid resistance [144] and resistance to microbiological attack [145,146] was improved for cellulose grafted with acrylonitrile, and increases in base resistance were also noted for MMA and a mixture of MMA and ethyl acrylate [13],... 

For the support material of electro-catalysts in PEMFC, Vulcan XC72(Cabot) has been widely used. This carbon black has been successfully employed for the fuel cell applications for its good electric conductivity and high chemical/physical stability. But higher amount of active metals in the electro-catalysts, compared to the general purpose catalysts, make it difficult to control the metal size and the degree of distribution. This is mainly because of the restricted surface area of Vulcan XC72 carbon black. Thus complex and careM processes are necessary to get well dispersed fine active metal particles[4,5]. 

In addition to the two major processes, cross-linking and chain modification (or cyclization), chain scission doubtless occurs also to varying degrees during conventional vulcanizations. Processes of this nature are not difficult to envisage in the presence of free radicals. The radical intermediate (II) may, for example, undergo /3-fission as follows ... 

R. F. Blackwell, Trans. Inst. Rubber Ind., 28, 75 (1952), has shown that very good agreement with Eq. (50) is obtained for a wide range of vulcanized natural rubbers using the same value for Cz. The constant Ci varies, of course, with the degree of vulcanization. 

Fig. 107.—Tensile strengths of natural rubber plotted against the degree of cross-linking with bis-azo vulcanizing agent (O), expressed as equivalent percent (pXlOO). Upper curve ( ) sample prepared using one equivalent percent of bis-azo compound plus monoreactive ethyl azodi-carboxylate for the total degrees of modification of the units indicated on the ordinate scale. (Flory, Rabjohn, and Shaffer.

Influence of the ZnCFO contents (3,0 5,0 7,0 phr) on crosslink kinetics of the modelling unfilled rubber mixes from NBR-26 of sulfur, thiuram and peroxide vulcanization of recipe, phr NBR-26 - 100,0 sulfur - 1,5 2-mercaptobenzthiazole - 0,8 stearic acid - 1,5 tetramethylthiuramdisulfide - 3,0 peroximon F-40 - 3,0, is possible to estimate on the data of fig. 7. As it is shown, the increase of ZnCFO concentration results in increase of the maximum torque and, accordingly, crosslink degree of elastomeric compositions, decrease of optimum cure time, that, in turn, causes increase of cure rate, confirmed by counted constants of speed in the main period (k2). The analysis of vulcanizates physical-mechanical properties testifies, that with the increase of ZnCFO contents increase the tensile strength, hardness, resilience elongation at break and residual deformation at compression on 20 %. That is, ZnCFO is effective component of given vulcanization systems, as at equal-mass replacement of known zinc oxide (5,0 phr) the cure rate, the concentration of crosslink bonds are increased and general properties complex of rubber mixes and their vulcanizates is improved. 

ZnCFO is the effective vulcanization active component of the sulfur, thiuram, peroxide and metaloxide vulcanization systems for isoprene, nitrile-butadiene and chloroprene rubbers at the same time it is not effective in resin vulcanization system for butyl rubber. On a degree of positive influence on the properties of elastomeric compositions vulcanization systems with ZnCFO are arranged in a line ... 

---