Cyclohexanone, acidity

Beckmann rearrangement of cvc7ohexanone oxime. M.p. 68-70 C, b.p. I39 C/12 mm. On healing it gives polyamides. Used in the manufacture of Nylon[6]. Cyclohexanone oxime is formed from cyclohexane and niirosyl chloride. U.S. production 1978 410 000 tonnes, capryl alcohol See 2-octanol. caiH Uc acid See oclanoic acid. 

C, b.p. 16UC. Manufactured by heating phenol with hydrogen under pressure in the presence of suitable catalysts. Oxidized to adipic acid (main use as intermediate for nylon production) dehydrogenated to cyclohexanone. 

H2N (CH2)a NH2- Colourless solid when pure m.p. 4LC, b.p. 204 C. Manufactured by the electrochemical combination of two molecules of acrylonitrile to adiponitrile followed by catalytic reduction, or by a series of steps from cyclohexanone via adipic acid. Used in the production of Nylon [6, 6]. 

Required Cyclohexanone, 20 g. hydroxylamine hydrochloride, 17 g. anhydrous sodium carbonate, 13 g. concentrated sulphuric acid, 50 ml. 25% aqueous potassium hydroxide solution, approx. 200 ml. chloroform, 120 ml. 

Dissolve 8 8 g. (9 0 ml.) of cyclohexanone in 50 ml. of glacial acetic acid, add 8 ml. of phenylhydrazine, and boil the solution under reflux for 5 minutes. Cool the solution, when the tetrahydrocarbazole will crystallise out. Filter at the pump, drain well, and recrystallise either from aqueous ethanol or (better) from aqueous acetic acid. The recrystallisation should be performed rapidly, for the tetrahydrocarbazole undergoes atmO" spheric oxidation in hot solutions after recrystallisation, the compound should be dried in a vacuum desiccator and not in an oven. Repeated recrystallisation should be avoided. The tetrahydrocarbazole, after thorough drying, is obtained as colourless crystals, m.p. 118° yield of recrystallised material, 11 g. 

Cyclohexanone, This is readily oxidised by a KjCr 07 - HjSO mixture to the crystalline adipic acid, m.p. 152 , precisely as for cyclohexanol (p. 335). 

Adipic acid is conveiiiently prepared by the oxidation of cyc/ohexanol (or cyclohexanone) with concentrated or with 50 per cent, nitric acid ... 

An interesting application is the preparation of 1 2 3 4-tetrahydrocarb azole (VI), which is formed when phenylhydrazine is added to a boiling aolutiai of cyclohexanone in acetic acid the plienylhydrazone (V) Intermediately produced undergoes ring closure directly ... 

The product (6 hexanohde) is a cyclic ester or lactone (Section 19 15) Like the Baeyer-Vilhger oxidation an oxygen atom is inserted between the carbonyl group and a carbon attached to it But peroxy acids are not involved m any way the oxidation of cyclohexanone is catalyzed by an enzyme called cyclohexanone monooxygenase with the aid of certain coenzymes... 

Furfuryl alcohol alone, or in combination with other cross-linkable binders such as phenoHc reins, chemical by-products and pitch, catalyzed with acid, gives carbon yields of 35—56%. Furfural together with cyclohexanone, pitch, or phenoHc resins gives, under acid catalysis, yields of 35—55% carbon under basic catalysis yields of 5—50% are achieved. FurfuryHdeneacetone resins (13 and 14), catalyzed by acid or base, give carbon yields of 48—56 and... 

Since adipic acid has been produced in commercial quantities for almost 50 years, it is not surprising that many variations and improvements have been made to the basic cyclohexane process. In general, however, the commercially important processes stiU employ two major reaction stages. The first reaction stage is the production of the intermediates cyclohexanone [108-94-1] and cyclohexanol [108-93-0], usuaHy abbreviated as KA, KA oil, ol-one, or anone-anol. The KA (ketone, alcohol), after separation from unreacted cyclohexane (which is recycled) and reaction by-products, is then converted to adipic acid by oxidation with nitric acid. An important alternative to this use of KA is its use as an intermediate in the manufacture of caprolactam, the monomer for production of nylon-6 [25038-54-4]. The latter use of KA predominates by a substantial margin on a worldwide basis, but not in the United States. 

Cyclohexane. The LPO of cyclohexane [110-82-7] suppUes much of the raw materials needed for nylon-6 and nylon-6,6 production. Cyclohexanol (A) and cyclohexanone (K) maybe produced selectively by using alow conversion process with multiple stages (228—232). The reasons for low conversion and multiple stages (an approach to plug-flow operation) are apparent from Eigure 2. Several catalysts have been reported. The selectivity to A as well as the overall process efficiency can be improved by using boric acid (2,232,233). K/A mixtures are usually oxidized by nitric acid in a second step to adipic acid (233) (see Cyclohexanol and cyclohexanone). 

Reactions. The most important commercial reaction of cyclohexane is its oxidation (ia Hquid phase) with air ia the presence of soluble cobalt catalyst or boric acid to produce cyclohexanol and cyclohexanone (see Hydrocarbon oxidation Cyclohexanoland cyclohexanone). Cyclohexanol is dehydrogenated with 2iac or copper catalysts to cyclohexanone which is used to manufacture caprolactam (qv). 

Reactions. The chemical properties of cyanoacetates ate quite similar to those of the malonates. The carbonyl activity of the ester function is increased by the cyano group s tendency to withdraw electrons. Therefore, amidation with ammonia [7664-41-7] to cyanoacetamide [107-91-5] (55) or with urea to cyanoacetylurea [448-98-2] (56) proceeds very easily. An interesting reaction of cyanoacetic acid is the Knoevenagel condensation with aldehydes followed by decarboxylation which leads to substituted acrylonitriles (57) such as (29), or with ketones followed by decarboxylation with a shift of the double bond to give P,y-unsaturated nitriles (58) such as (30) when cyclohexanone [108-94-1] is used. 

Dilute nitric acid can be used to oxidize an aliphatic hydrocarbon. For example, a significant use for nitric acid is the oxidation of cyclohexanol and cyclohexanone (qv) to produce adipic acid (qv). Most adipic acid is used for the production of nylon-6,6. 

Thermal decomposition of hydroxyalkyl hydroperoxyalkyl peroxides produces mixtures of starting carbonyl compounds, mono- and dicarboxyHc acids, cycHc diperoxides, carbon dioxide, and water. One specific hydroxyalkyl hydroperoxyalkyl peroxide from cyclohexanone (2, X = OH, Y = OOH) is a soHd that is produced commercially as a free-radical initiator and bleaching agent (see Table 5). On controlled decomposition, it forms 1,12-dodecanedioic acid (150). 

Adipic acid (qv) has a wide variety of commercial uses besides the manufacture of nylon-6,6, and thus is a common industrial chemical. Many routes to its manufacture have been developed over the years but most processes in commercial use proceed through a two-step oxidation of cyclohexane [110-83-8] or one of its derivatives. In the first step, cyclohexane is oxidized with air at elevated temperatures usually in the presence of a suitable catalyst to produce a mixture of cyclohexanone [108-94-1] and cyclohexanol [108-93-0] commonly abbreviated KA (ketone—alcohol) or KA oil ... 

PUtzing erReaction. Quinoline-4-carboxyhc acids are easily prepared by the condensation of isatin [91-56-5] (16) with carbonyl compounds (50). The products may be decarboxylated to the corresponding quinolines. The reaction of isatin with cycHc ketones has been reported, eg, the addition of cyclohexanone gives the tricycHc intermediate (17) [38186-54-8] which upon oxidation produces quinoline-2,3,4-tricarboxyhc acid [16880-83-4] (51). 

Sahcyhc acid, upon reaction with amyl alcohol and sodium, reduces to a ring-opened ahphatic dicarboxyhc acid, ie, pimelic acid (eq. 5). The reaction proceeds through the intermediate cyclohexanone-2-carboxyhc acid. This novel reaction involves the fission of the aromatic ring to i j -hexahydrosahcyhc acid when sahcyhc acid is heated to 310°C in an autoclave with strong alkah. Pimelic acid is formed in 35—38% yield and is isolated as the diethyl ester. 

---